BRILLIANT 20353 Velocity II 3In1 Bathroom Heater Instruction Manual

BRILLIANT 20353 Velocity II 3In1 Bathroom Heater

Product Information: VELOCITY II 3-in-1 BATHROOM HEATER

Please read all instructions before commencing installation even if you are familiar with this type of product.

THIS FITTING MUST BE INSTALLED BY A QUALIFIED ELECTRICAL CONTRACTOR in accordance with the latest edition of AS/NZS 3000

Parts List

The VELOCITY II 3-in-1 Bathroom Heater is a versatile product that provides instant heat and ventilation for your bathroom. It comes with various components to ensure efficient operation:

1. Bathroom Heater
2. 9W R63 LED Globe Cool White
3. 275W Heat Lamps
4. Ø125mm Duct 1.5m Length
5. Exterior Vent
6. Switch Plate (20353: 3 gang switch, 20254: 4 gang switch)

Product Usage Instructions:

For your Safety

• This fitting must be installed by a qualified electricalcontractor in accordance with the latest edition of AS/NZS3000.
• Do not attempt to install or modify the product yourself.
• Make sure to read all instructions before installation, even ifyou are familiar with this type of product.
• If you have any questions or concerns, contact the supplier orlocal agent for assistance.
• To prevent electrical shock, please ensure that power is DISCONNECTED before installing.
• Be aware of the height of your installation. Refer to ‘Working at Heights “ guide from your local or State Authorities.
• This product must be used only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. If you have questions, contact the supplier or local agent.
• All wiring must be carried out by a licensed electrician in accordance with all applicable national / local codes and standards. Also check with the local council regulations regarding installation of exhaust fans.
• When cutting into the ceiling material, care must be taken to ensure you do not damage the existing ceiling structure, existing electrical wiring and other hidden utilities.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the unit.
• The lamps are extremely hot when in use. Allow all lamps to cool sufficiently before touching or replacement.
• For the purpose of avoiding any fumes leaking into your bathroom, the duct for the heater must not be laid together with ducts for air-fuelled water heaters or other open-fire appliances.
• Any alterations or additions to building wiring must be completed by a licensed electrician or person authorised by legislation to work on the fixed wiring of any electrical installation

Introduction and Considerations

• Always operate the product from a power source that matches thevoltage, frequency, and rating indicated on the rating label.
• The Infra-Red lamps are designed to provide instant heat topersons standing directly underneath them. Install the unit abovean area where “drying off” usually occurs.
• This product is designed for installation in flat ceilingsonly. Do not mount it on a sloping ceiling or a vertical wall.
• The heater lamps are not designed for extended periods ofoperation.
• Locate and install the product in accordance with the requirements of AS/NZS 3000 and local building codes.
• Do not install in a location where there is a possibility of water splashing onto the lamps.

Ventilation Requirements

• For the exhaust fan to work efficiently, replacement air of avolume equivalent to what is being extracted must be able to enterthe room.
• Generally, air would be drawn under the door, or through a slightly open window. If the room is airtight, the fan will operate poorly. Air flow path should ideally pass over the steam source.
• It is also essential the there is adequate space within the roof cavity so the steam can dissipate.
• Air flow path should ideally pass over the steam source.
• If the roof cavity is restricted or not well ventilated, it isrecommended to use duct and vent to extract steam to an outside area.

Clearance Requirements:

• The unit must be mounted at least 250mm away from verticalwalls.
• A minimum clearance of 100mm is required above the top of theunit.
• A minimum of 50mm clearance is required between the sides ofthe unit and joists, walls, or insulation.

Installation

Note: Connect ducting (if required) after the unit is installed in the ceiling.

1. Gently insert the unit into the cut-out hole, ensuring to movethe side mounting clips inwards so that the body fitssecurely.

2. Refer to the electrical wiring diagram for proper connection.

3. If your model has two heat lamps, a second heat switch is notrequired.

4. This unit must be mounted at least 2 metres above the floor and at least 250mm away from vertical walls.

5. Remove heat globes and LED globe from the unit to prevent breakages.

6. Remove the grille by releasing 4 springs in each corner of the unit.

7. Ensure area behind the installation location is clear of all cables, pipes, joists or hidden utilities.

8. Use the template provided to mark and cut a hole in the ceiling (Refer specifications for hole size).

9. Remove rear terminal cover and connect wires as per wiring diagram below. Refit terminal cover.
   Note : Connect ducting (if required) after the unit is installed in the ceiling.

10. Gently insert the unit into the cut out hole ensuring to move the side mounting clips inwards so that the body can pass through the hole without damaging the plasterboard. Tighten the screws for the clips ensuring that the unit is held securely in place by 4 x clips. Additional screws can be applied around the metal flange plate to hold the unit to the ceiling.

11. Secure grille with springs (20353: use inner two holes on grille) and insert lamps/LED globe.

12. Attach ducting if required to extract the air to the outer wall using 1.5 long flexible ducting, cable ties and vent outlet grille provided. Fix and tighten cable ties firmly to hold the flexible duct to the unit and the outer wall vent.

13. Ensure that the flexible duct, when connected to the unit doesn’t obstruct or block the anti-draft stopper, as it would reduce the overall airflow.

Electrical wiring diagram

The unit requires ‘permanent active’. The fitting is fitted with a thermal cut-out which will turn the motor (FAN) ‘ON’ when them internal temperature exceeds 80˚C.

1. Double pole disconnecting device must be fitted in the circuit.
2. Ensure the power is switched “OFF” at the mains before commencing installation.
3. Remove the cover on the back of the enclosure to access the terminals.
4. Connect wires as per electrical wiring diagram and markings adjacent to terminal block.
5. Replace the cover removed earlier.

Operation

This unit uses Infrared heating lamps as a heat source. It also has an exhaust fan and an LED globe.

• Heating: Switch the ‘Heat’ button ‘ON’ on the wall switch. The heat globes provide instantaneous heat from the moment they are switched ‘ON’.
• Exhaust Fan: Use the switch button ‘Fan’ to turn it ON and Off.
• LED globe: Operate the LED globe independently from heat globes, using ‘Light’ On /Off switch button.

Cleaning

• Switch off the power before commencing cleaning and wait until the globes cool down.
• Regularly wipe globes and front fascia with soft cloth soaked with water or neutral detergent if required.
• Clean the exhaust fan from dust and dirt with dry or wet cloth if required.
• Clean the exhaust ducting kit and ensure airways are clean and there are no obstructions at the exit from the wall.

Replacement Lamps

• Heat Lamps – Hard Glass, Infrared, R125, 240V, 275W
• LED light – R63, 240V, 9W Max, 860lm, Cool White

Specifications

Dimensions

| 20353/05 – 400mm L x 220mm W x (180mm H excluding front grille) 20354/05 – 374mm L x 374mm W x (210mm H excluding front grille)
Noise| <45 dB
IP rating| IPX2
Weight| 3kg (20353/05), 4kg (20354/05)

Warranty

Brilliant Lighting warrants this product against defects in manufacture and workmanship for a period of 3 years from date of purchase.. This warranty is only valid for products installed by a qualified electrical contractor and operated within the guidelines specified by Brilliant Lighting, and within the correct operating voltage ranges as stated on the product’s rating label.

Warranty does not include damage or loss arising from incorrect installation, operation or maintenance of this product, damage caused through modification, incorrect installation, service by unqualified or unauthorised personnel or lack of regular maintenance and cleaning. Proof of installation by qualified personnel may be required, e.g.. Electrical Safety Certificate. Proof of purchase must be supplied with all warranty claims.

This warranty is provided in addition to any other rights and remedies of the customer under any law. In applications not intended for household, personal or domestic use, liability is limited to replacement or reimbursement of product only.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to be of acceptable quality and the failure does not amount to a major failure.

Any claim under this warranty must be made within the specified warranty period from date of purchase of this
product. To make a claim under the warranty, take the product (with proof of purchase ­ receipt or similar) to the store where you purchased the product or contact Brilliant Lighting at the address below.

This warranty is given by:

Brilliant Lighting (Aust) Pty. Ltd.

• ABN 37 006 203 694
• 956 Stud Road Rowville, VIC 3178
• Phone: 03 9765 2555
• Email: info@brilliantlighting.com.au
• Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>