DS18 SLG-RSUB10LD Polaris Slingshot Rear Storage Compartment Subwoofer Owner’s Manual

June 13, 2024
DS18

**DS18 SLG-RSUB10LD Polaris Slingshot Rear Storage Compartment Subwoofer Owner’s Manual

**

INTRODUCTION

If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding this durable Polyethylene 10″ Subwoofer Enclosure by DS18. This enclosure allows you to mount one 10″ subwoofer using the rear storage compartment to give you the bass that your stereo system deserves. This enclosure comes with one NXL-10SUB/BK Subwoofer with RGB LED Lights in black textured finish to match the factory’s look. Easy to Install using supplied bolts and brackets directly into place.

FEATURES

  • One NXL-10SUB/BK subwoofers included
  • 300w rms /600w max power handling
  •  4 ohm total load impedance
  • Easy to install – all hardware and wiringincluded
  • OFC tinned 12GA wiring for more power handling and durability
  • 6 core 3.2 ft / 1m input wires for rgb lighting d speaker
  • Fits slingshot models from 2015 or later
  • Works for both driver and/or passenger side storage compartment
  • Coated metal bracket for better resistance to the elements
  • Black OEM finish
  • Durable (PE) waterproof enclosure with uv protection
  • 0.75ft3 / 21l ported / vented enclosure type.
  • Damping material for better subwoofer performance.

WHAT’S IN THE BOX

  • Subwoofer Enclosure with One NXL-10SUB/BK included.
  • Face Plate
  • Mounting Brackets
  • 6 x M6x16mm Screws and Washers
  • 4 x M6x40mm Screws and Washers
  • 6 x M6 Clip-On Nut
  • Speaker Wiring

INSTALLATION

Starts by moving the seats all away forward to get easy access to this area, it is optional if you want to remove the seats for running wires or easy installation on both driver and passenger side of  the vehicle. (Picture 1)
Installation Instruction

Remove the Passenger rear deck hump using a T25 TORX socket to extract the (2) screws on front bottom of the piece and pull it to the front, (Picture 2)
Installation Instruction

Remove the Driver rear deck hump using a T25 TORX socket to extract the (2) screws on front bottom of the piece, then remove the gas cap and using an oversized pliers, un-screw the Ring-Nut that holds the gas tube in place, after this you can pull out the piece. (Picture 3)
Installation Instruction

Remove both driver and passenger side rear hoop accent using a T40 TORX socket to extract the (2) screws on bottom of the piece and a T25 TORX to extract the (2) screws on top of the piece and pull it to the font, then using the T40 TORX to extract the (2) screws in the back of the piece and pull it to the back. (Picture 4)
Installation Instruction

Remove screws that were located underneath the head covers once the humps are removed. (Picture 5)
Installation Instruction

Remove the doors that cover both driver and passenger side rear storage compartment. (Picture 6)
Installation Instruction

Remove all T40 TORX screws and (2) push clips that are located on back panel. (Picture 7)
Installation Instruction

For 2017 and newer models, use the six (6) supplied clip nuts on the left and right side to mount the cabinet. (Picture 8)
Installation Instruction

This kit needs an aftermarket amp pre-installed with the speaker wires in this location, only after this step can you connect the speakers using the aftermarket amp’s speaker wire and RGB LED wires (optional) of the LED module (LED -BTC not included). (Picture 9)
Installation Instruction

If the enclosure does not have the brackets installed already, go ahead, and put it in place and secure it using the supplied bolts and washers. (Picture 10)
Installation Instruction

Grab the top and bottom of the enclosure and slide the subwoofer box into place in the rear compartment.
(Picture 11)
Installation Instruction

Once finished, re-install the rear panel, and install the factory T40 TORX screws back to secure SLG-RSUB10LD enclosure. (Picture 12) (Picture 13)
Installation Instruction

Attach the face plate using the supplied M6x40mm screws. (Picture 14)
Installation Instruction

Re-install everything back in order from the rear hump and hoop accent in the same way that was pulled out. This concludes the installation of the SLG- RSUB10LD and it is ready to enjoy your new sound system upgrade!

CONNECTION OPTIONS

  1. If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
    Connecting Instruction
    Colors Indicators
    Blue LED (-)
     Red LED (-)
    Green LED (-)
      Black 12V DC (+)
     White Speaker (+)
     Grey Speaker (-)

  2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

    • Black wire”BK” connected to battery Positive (+) 12V
    • White Color Light “R”; “B” and “G” connected to battery Negative (-)
    • Green Color Light “G” connected to battery Negative (-)
    • Red Color Light “R” connected to battery Negative (-)
    • Blue Color Light “B” connected to battery Negative (-)
    • Purple Color Light “R” and “B” connected to battery Negative (-)
    • Yellow Color Light”R” and “G” onnected to battery Negative (-)
    • Cyan Color Light “B” and “G” connected to battery Negative (-)
      Connecting Instruction

GENERAL

  • Speaker Size: 10″ / 254mm
  • Total Impedance: . 4 Ohms
  • Total RMS Power Handling: 300W
  • Total MAX Power Handling: 600W
  • Sensitivity (1w/1m): 89dB
  • Frequency Response: 35-250Hz
  • Recommended Lo Pass Crossover: 100Hz

SPEAKER SPECIFICATIONS

  • Voice Coil Diameter: 2″ / 50.8mm
  • Voice Coil Former Material: Glass fiber
  • Winding Material: CCAW
  • Cone Material: Injection Molded Polypropylene + UV Compliant
  • Dust Cap Material: PPI
  • Magnet Material: . Ferrite
  • Magnet Weigh: 72oz

BOX SPECIFICATIONS

  • Internal Volume: 0.75 ft3 / 21L
  • Load Configuration: Single
  • Box Type: Ported / Vented
  • Port Tuned (Fb): 40Hz
  • Box Material: Polyethylene (PE
  • Finish Materia: Black
  • 3Db Dropping Point (F3): 45Hz
  • Waterproof Rating: IP65 (With Ports Covered)

MEASUREMENT

  • Overall Height: 18.78″ / 477mm
  • Overall Width: 15.25″ / 388mm
  • Overall Depth: 14.31″ / 363.3mm

MEASUREMENTS

DimensionsDimensions
Dimensions

WARRANTY

Please visit our website DS18.com for more information on our warranty policy.

We reserve the right to change products and specifications at any time without notice. Images may or may not include optional equipment.

WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov

FOR MORE INFORMATION
PLEASE VISIT
DS18.COM

Apps

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DS18 User Manuals

Related Manuals