SmartTag
STG-866B User Manual

STG-866B SmartTag Bluetooth Tracker

Regulatory Information
Product Name: SmartTag
Model: STG-866B
FCC ID: VPE-STG-866B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Cadi Scientific Pte Ltd
31 Ubi Road 1

09-01

Singapore 408694
Singapore
PRECAUTIONS

• Keep batteries away from children.
• Do not swallow batteries.
• Do not throw batteries into water.
• Do not throw batteries into fire.
• Do not short-circuit batteries. Battery must be fit into tag in correct orientation.
• Do not replace battery with incorrect type. Incorrect type of battery replacement may cause risk of exposure.
• Battery should be dispose according to the instructions

Product Information

• Product model: STG-866B
• Product name: SmartTAG
• Manufacturing site: 31 Ubi Road 1, #09-01 Annex Building, Singapore 408694

User Manual Version Information

• This version is subject to change or upgrade without notice
• Version: 2
• Issue date: 16 Jan 2023

Declaration
Cadi Scientific Pte Ltd reserves the right to change the product described in this User Manual. All information contained in this User Manual is subject to change without notice.

Introduction

The STG-866B is a battery powered location tracking tag. Location tracking is achieved using a combination of technologies based on low frequency (LF), infrared (IR), and BLE signals that give robust performance even in challenging environments.

Location Reporting Method

When the STG-866B passes by a LF beacon or exciter (typically installed at key chokepoints or egress points) it will receive over its LF receiver a location ID transmitted by the LF beacon. The tag will then advertise this location ID over its BLE transmitter.
Access points that are in range of STG-866B’s advertisements will be able to receive STG-866B’s location.
When the STG-866B enters a room that has a IR beacon installed, the tag will receive a location ID transmitted by the IR beacon. The tag will then advertise this location ID over its BLE transmitter.
Access points that are in range of STG-866B’s advertisements will be able to receive STG-866B’s location.

Mounting Method

The tag can be mounted on assets or equipment using a mounting bracket accessory.

Specifications

Dimension
Weight| 42.5mm x 70mm x 23mm
TBC
2| Power
Rechargeable
User replaceable
Battery type| No
Yes 3.6v
(ER17335-2 3.6V LiSOCl2 primary battery)
3| Operating Environment
Temperature
Humidity| 0oC to 55oC
0 – 95% RH non-condensing
4| RF Specifications
Frequency| 2.4GHz (standard advertising channels)
5| LF Receiver Specifications
Frequency| 125kHz (receive only)
6| IR Receiver Specifications
Frequency| 38kHz (receive only)
7| Location-Update/Beacon
Update rate| Immediate upon detection of LF or IR location ID
8| Interface
Visual
Audio| 1 x Red LED
1 x Green LED 1 x Beeper
9| Compliance| RF
To be confirmed
EMC
To be confirmed
Safety
** To be confirmed

Battery Change Instructions

5.1 Remove rear battery cover
– Pry at the rear cover at the 2 release points using a flat tip screw driver

5.2 Disconnect depleted battery

1. Remove battery from tag to make room
2. Apply straight pulling or tugging action to disconnect depleted battery

5.3 Connect fresh battery

5.4 Ensure correct wire placement to prevent obstruction to rear cover

5.5 Reset Tag

5.6 Put back rear battery cover

Trouble-shooting Guide

6.1 There is no location update on the tracking system when the tag passes by an exciter
This could be due to several reasons.
a. Battery may have depleted
If tag’s LEDs are not blinking at all, then battery may have been depleted. Replace depleted battery with a fresh one.
b. Battery strength may be too low
If tag’s red LED is blinking, then battery strength may be too low. Replace weak battery with a fresh one.
c. Access Point coverage may be insufficient
The tag may be out of range of the the Access Points. Adjust the location of the Access Points or place additional Access Points to ensure sufficient coverage.
d. LF coverage may be insufficient
The tag may be out of range of the exciter. Adjust the location or the power of the exciter to ensure sufficient LF coverage.
e. The tag may have malfunctioned
Replace malfunctioned tag.

CADI SmartSense – SmartTag STG-866B
User Manual v2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>