Cooper Electric 064875 Wireless Motion Sensor Instruction Manual
- June 12, 2024
- Cooper Electric
Table of Contents
Cooper Electric 064875 Wireless Motion Sensor
This product is a connected accessory which requires you to buy and install one of these first:
- with Netatmo” connected starter pack and “… with Netatmo ” connected power outlets, switches (with dimmer option).
- Connected lighting micromodules.
- Radiant with Netatmo Gateway and radiant with Netatmo Switch, Dimmer or Receptacle.
- Adorne with Netatmo Gateway and adorne with Netatmo Switch Dimmer or Receptacle.
Pack contents
Wireless motion sensor
Specifications
This product can control up to 20 connected switches (with dimmer option),
micromodules, cable outlets and power outlets «… with Netatmo»
Frequency bands: 2.4 – 2.4835
GHz Power level: < 10 mW
INSTALLATION INSTRUCTIONS
Open the front cover
Do not insert the batteries now
Do not fix the motion sensor to the wall now.
The installation will be finalized on step 6.
Start the wireless motion sensor configuration
Outside US:
Press the middle of the wireless master switch until its light briefly turns
green, and then stop pressing. The indicator lights on the products which you
have wired will turn green.
US:
Press the Gateway EZ button for 5 seconds and let go. The LED will turn solid
green or follow the app to add device.
Insert the batteries in the wireless motion sensor
The motion sensor light will flash green and then switch off.
Note: if the motion sensor flashes green green red, then remove the
batteries and restart on Step 2
Pair the wireless motion sensor to a wired connected product
Make sure that the indicator lights on the wired products are green and not
flashing. If not go back to step 2 and then come back to step 4.
- To pair a wireless motion sensor with a connected light switch, go to step 4.1.1
- To pair a wireless motion sensor with a connected micromodule, go to step 4.2.1
- To pair a wireless motion sensor with a connected power outlet, go to step 4.3.1
Pair a wireless motion sensor with a connected light switch
Step A: Press the ON button on the wireless motion sensor you wish to pair,
while tapping it three times onto the light switch you wish to control.
Step B: The indicator lights on the two products will flash blue rapidly.
Step C: The indicator lights on the two products will briefly turn blue and
stop flashing. Step D: The light on the wired product will turn green again
and the light on the wireless motion sensor will switch off. The pairing was
successful.
Check the correct pairing
Press the ON and OFF buttons of the wireless motion doesn’t, come back to
step 4.1.1.
Pair a wireless motion sensor with a connected micromodule
Phase A: Press the ON button on the wireless motion sensor you wish to pair,
while tapping it three times onto the micromodule you wish to control.
Phase B: The indicator lights on the two products will flash blue rapidly.
Phase C: The indicator lights on the two products will briefly turn blue and
stop flashing
Phase D: The light on the wired product will turn green again and the light on
the wireless motion sensor will switch off.
Check the correct pairing
Press the ON and OFF buttons of the wireless motion doesn’t, come back to
step 4.1.1
Pair a wireless motion sensor with a connected power outlet
Step A: Press the ON button on the motion sensor you wish to pair, while
tapping it three times onto the power outlet you wish to control.
Step B: The indicator lights on the two products will flash blue rapidly.
Step C: The indicator lights on the two products will briefly turn blue and
stop flashing
Step D: The light on the wired product will turn green again and the light on
the wireless motion sensor will switch off.
Multiple pairing
You can control several connected switches, micromodules and power outlets by
repeating the step 4 on each product you wish to control. OR you can add
control of more devices in the Home+Control application.
Complete the configuration
Location concerns
Fix the motion sensor
For optimal use, the motion detector should be placed at a height of
approximately 2.50 m [8 feet] from the ground.
Set up the motion sensor
By default, the motion detector is set to a minimum delay (15 seconds), a
maximum light sensitivity (1000 lux) and a maximum sensor sensitivity (8
meters). If you want to change these settings, follow the steps below.
Adjust the time delay
To increase the time that the associated product remains ON (eg, light),
turn the screw (potentiometer) clockwise.
Adjust the ambient light sensitivity
In order for the sensor to detect only when it is dark, turn the screw
(potentiometer) counterclockwise.
Adjust the motion sensor sensitivity
To reduce the sensitivity of the motion sensor, turn the screw (potentiometer) counterclockwise. The detection will then be at a shorter distance.
Close the front cover
For outdoor installation with IP44 degree of protection
Break off the two fins at the bottom of the product below the snaps to allow
drainage.
To add a connected product to your connected home:
Follow instructions in the Legrand Home + Control application (Settings/Manage
My Home).
Note: If you have not already assigned the motion sensor to a room, the motion sensor will be listed under the “Unplaced products” section.
Reset To Factory Default:
To manually reset the device to factory defaults, press and hold the EZ Button
for 10 seconds until you see the LED blink red, then release. The LED will
turn off when the reset is complete.
Outside US:
www.legrandoc.com/064875
Legrand – Pro and Consumer Service BP 30076 87002 Limoges CEDEX FRANCE
www.legrand.com
US:
Question? We’re here to help.
Phone: 1-877-833-3303
Email: smartlights@legrand.us
Battery replacement
SIMPLIFIED EU DECLARATION OF CONFORMITY
The undersigned, Legrand declares that the radio-electric equipment
referred to in these instructions complies with directive 2014/53/EU.
The full text of the EU declaration of conformity is available on the
following website : www.legrandoc.com
REGULATORY INFORMATION
FCC NOTICE : This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly
approved by the manufacturer will void the warranty and the user’s authority
to operate the equipment.
Contains FCC ID: 2AU5D-064875
IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 20 cm to the human body.
Note: Any changes or modifications to this device that are not expressly
approved by the manufacturer, will void the warranty and the user’s authority
to operate the equipment.
IC: 25764-064875
HVIN: 064875
References
- Welcome to Legrand - Legrand
- Infraestructuras eléctricas y digitales | Legrand
- Legrand E-catalog International | Electrical Ranges of products & Connected Solutions
- legrandoc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>