ZLINE RBIV-30 Dual Built-In Refrigerator Instruction Manual

RBIV-30 Dual Built-In Refrigerator

DUAL BUILT-IN
REFRIGERATOR
www.zlinekitchen.com

ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams  is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to  providing you an elevated experience in the heart of your home. With an endless selection of  features and finishes, our inspiration is your reality.

ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury  designs and professional features into everyone’s homes. Because we continually strive to improve  our products, we may change specifications and designs without prior notice.

WARNING: This product can expose you to chemicals including nickel, which is known to the  State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING THE PRODUCT

• Please note that the installation process for your dual built-in refrigerator requires  combining two RBIV-30 model refrigerators to create one RBIV-60 unit.
• Always follow allow applicable safety instructions in this manual as well as the  manuals for ZLINE’s built-in refrigeration models (RBIV-30 and RBIV-36).
• IMPORTANT: This is a complex installation procedure that should only be per formed by qualified professionals and technicians.
• The manufacturer will not be responsible for any damage to property or to per sons caused by incorrect installation, improper use of the appliance, or failure to  heed the warnings listed.

R600A REFRIGERANT: This product contains R600a isobutane  refrigerant, which is a very eco-friendly natural gas. However, it is also  flammable. Please follow the warnings and installation instructions below.

• If the products have been transported horizontally, you must wait a minimum of 4  hours after standing them upright before plugging it in.
• Cut-out dimensions of the installation area must be suitable to safely fit the  product for full installation.
• Dimensions, features, and position of objects used to support and affix the  product to this area must be suitable.
• Minimum clearances between product parts and surrounding structures must be  suitable; minimum dimensions and proper organization of ventilation holes must  be observed.
• The product must be connected to the main power outlet, and corresponding  connections of other components must be suitable.
• The product must be able to be disconnected from the power supply if needed  after installation; the outlet or fuse must be accessible to disconnect the product.
• Extension cables or ungrounded (two-terminal) adapters must not be used.

You must wear gloves and eye protectors when installing the product.

You must also take measures against high noise levels when using a drill to drill into the floor or wall.

The product must be installed by a qualified technician according to the installation instructions.

IMPORTANT SAFETY INSTRUCTIONS

DISPOSING OF THE PACKAGING MATERIALS

• The package has been designed to protect the product during transport and shipping. The packaging materials used are designed to not harm the environment  and should be recycled after the appliance is installed.

• All plastic packaging materials, bags, etc., must be disposed of safely and kept  out of the reach of children.

This manual has been prepared to help qualified professionals with installation of the appliance. The User and Installation manuals for  ZLINE’s built-in refrigeration models (RBIV-30 and RBIV-36) must also  be taken into consideration, as they contain important information  about operation and safety. You may get seriously injured and your  products damaged if you ignore the warnings given in these manuals.

The products may tip over since they are quite heavy. For this reason,  safety precautions must be taken. The doors must be kept closed until  the combined product reaches the final install destination, and must be  transported in accordance with the installation instructions.

COMPLIANCE WITH THE WEEE DIRECTIVE AND DISPOSING OF E-WASTE:

• This product conforms to the EU WEEE Directive (2012/19 EU).

• This product bears a classification symbol for “waste electrical and electronic  equipment,” otherwise known as WEEE.

• This product has been manufactured from high-quality parts and materials that  can be reused and are suitable for recycling.

• Therefore, do not dispose of the product with normal domestic waste or other waste at the end of its service life.

• Take it to a collection center for recycling electrical and electronic equipment.

• Please consult your local government authority to learn about appropriate collection center location.

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION ENCLOSURE REQUIREMENTS

• The floor on which the dual refrigerator will be installed must be capable of  bearing a minimum of 2,400 pounds (1,089 kg).

• The kitchen floor and bottom of the product must be level. Otherwise, air flow for  the unit’s cooling system may be impeded or reduced. Use a level to be sure.

• There must be no objects preventing installation of the product to the back and  side walls of the product’s cut-out installation area.

• Cut-out dimensions of the cabinets where the product will be installed must be in  strict conformity with the dimensions given in the manual.

• Do not install the refrigerator directly adjacent to another refrigerator. Otherwise,  condensation and damage may occur

• The installation area must not be subjected to direct sunlight and it must be away  from heat sources, such as microwaves, ovens, radiators, etc.

• The ambient temperature must be between 61°F (16°C) and 100°F (38°C), depending on where the unit is installed. Otherwise, function errors may occur when the product is running.

• If it is not possible to avoid installing the product near a heat source, the minimum  clearances given below must be maintained:

 • 1 3/16″ (30 mm) from electric ranges or ovens.

 • 12″ (305 mm) from gas or fuel operated ranges or ovens.

• The dedicated circuit breaker for this unit must be easily accessible in case of an emergency; it must not be hidden behind the product.

• The electrical plugs and cords must not touch the back surface of the product. Otherwise, they may get damaged due to the vibration of the product.

• If the humidity level is high where the product is used, corrosion may occur on the outer surface of the product. Keep the area where the unit will be installed dry and well-cleaned to avoid corrosion.

IMPORTANT SAFETY INSTRUCTIONS

Failure to follow these instructions may result in death, fire,  or electric shock. Connecting the grounding conductor of the equipment to an improper place may lead to electric shock.  Please have the grounding checked by a qualified electrician or  service technician.

Installation, repair, and other procedures performed by  unqualified persons may cause danger. Before installing the  appliance, make sure that the voltage, load, and circuit current parameters on the data plate are in compliance with the power  mains in your house.

If the electrical wiring or power supply of the house needs  alteration, the necessary procedures must be performed by  a qualified electrician. The plugs must be installed only by a licensed electrician.

CABINETS

Make sure that the cabinets where you will install the appliance have been safely  mounted in your kitchen. Your cabinets must be securely connected to the floor and  walls properly and with suitable connections.

For the best installation, clearances between cabinets and the product must be in  compliance with the values specified in this manual and in the Installation Manual for  ZLINE’s built-in refrigeration models (RBIV-30 and RBIV-36).

Side walls must be free of any obstructions and their surfaces must be flat.

Note:  Minimum thickness of the side walls is 5/8″ (16 mm). The minimum thickness of the doors to be attached to the product must be 3/4″ (19 mm).

VENTILATION

Ventilation panels where the air enters and exits the unit must not be blocked or obstructed. In addition, you must periodically clean the dust and dirt that accumulates on the vent holes to ensure adequate ventilation.

IMPORTANT SAFETY INSTRUCTIONS

The installation process for your dual built-in refrigerator requires combining two RBIV-30 model refrigerators to create one RBIV 60 unit. Scan the QR code to access the Installation Manual for ZLINE’s built-in refrigeration models (RBIV-30 and RBIV-36).

ELECTRICAL CONNECTION

• Never use an extension cable or cord with this unit.

• The dedicated electrical outlet receptacle(s) for this unit must be grounded and checked  by an authorized electrician.

• The location of the electrical wiring must comply with the dimensions specified in  this installation manual.

CAUTION RISK OF ELECTRIC SHOCK

Electrical grounding is necessary. This appliance is equipped with two  3-pin plugs to protect you against possible electric shocks.

• Do not remove the round grounding terminal from the plugs.
• Do not use 2-pin grounding adapters.
• Do not use extension cables or cords to energize the product.

ATTENTION

Do not connect the grounding cable to any gas pipes. Please have the grounding checked by a qualified electrician if you are not sure about  the grounding of the product. Do not install a fuse on the neutral line  or grounding circuit.

Please wait 3-6 hours after installing the unit before plugging it in to protect it against possible damages. This way, the refrigerant and the lubricants in the system are given proper time to balance. WARNING

WATER CONNECTION

• The pressure of the main water supply must be in compliance with the values specified in this manual, and the location of the water system must comply with the dimensions specified in this manual.

A bypass is recommended for the water filtering system if a reverse  osmosis system is used. INFO

BEFORE INSTALLATION

CABINET DIMENSIONS

• Much like ZLINE’s RBIV-30 and RBIV-36 built-in refrigerators, the RBIV-60 model is  a panel-ready appliance designed to be a permanent fixture in your custom kitchen;  therefore, precise cabinet cutouts and superior attention to detail are required for  seamless integration.
• Since all kitchen layouts vary, the dimensions below must be checked by a qualified  professional before starting installation.

BEFORE INSTALLATION

RBIV-60 ELECTRICAL AND WATER REQUIREMENTS

• Each RBIV-30 appliance is provided with a NEMA 5-15P plug and a 3-pin  power cable designed to be connected to a 120VAC, 60HZ power receptacle.  • Therefore, we recommend both RBIV-30 units be plugged into independent circuits. They can be plugged into the same outlet, but please note the circuit must  have a dedicated 15-amp breaker that is not shared with any other appliance to  avoid exceeding the combined power requirements.

• From a water standpoint, while both RBIV-30 units also come with their own wa ter supply, a qualified technician can easily tee off the water supply to provide  water to both units if the customer desires.

• Refer to the diagrams below and on the following page, and please refer to your  RBIV-30 Installation Manual for additional information for electrical and water  requirements and other installation needs.

ELECTRICAL LOCATION

• Location of electrical wiring must be within the range given below. 2” (50.8 mm)

ATTENTION Do not use extension cables or two-pin adapters and do not remove  the ground terminal of the grounding cable.

ATTENTION A qualified electrician must ensure that the poles of the socket are  connected correctly and that the appliance is properly grounded.

 BEFORE INSTALLATION

WATER SYSTEM LOCATION

• The water connected to the dual refrigeration unit must be potable.

• Location of the water system must be within the range outlined in the graphic at the  bottom of this page.

• The unit’s water system must be connected to the main water system in the house. The user  must be able to switch the water system on/off with a valve when necessary. • Objects that might pierce the water hoses or cause them to twist must not be present  where the water line is installed.

• Pressure of the water system must be between 25-80 psi (1.7-5.5 Bar).

• If the water pressure exceeds 80 psi, install a pressure-limiting device or water pressure  protector to the inlet valve. Never install or operate the appliance if it’s possible for the  water pressure to exceed 120 psi.

• Make sure there is no leakage when making water connections.  Otherwise, there will be water on the floor and the cabinets may  get damaged.

• You will need a hose with a minimum length of 60″ (1524 mm)  and a diameter of 1/4″ (6.4 mm) for water connections of the  product during installation.

• A connector that has a thread with an external diameter of 1/4″  (6.4 mm) must be used to connect the hose end to the product. • Before completing installation, make sure water flows and there is  no leakage. Damage may occur if leaks are present.

BEFORE INSTALLATION

DUAL INSTALLATION COMPONENTS

INSTALLATION

PARTS PROVIDED

ATTACH THE ADHESIVE FOAM DIVIDER

1. Approach the refrigerators from behind and angle one of them out.
2. Next, measure 2 1/8” from both the top and left corner of the side of the unit.
3. Using a level, ensure the adhesive foam divider (Item No. 1) remains parallel to the edge of the unit.
4. Peel the protective sticker off the divider and carefully press into place. 2 1/8” 

INSTALLATION

MOUNT UPPER BRACKETS AND LOWER BACK BRACKET TO CONNECT THE REFRIGERATORS

1. On the back of one unit near the top, find the location for one plastic mounting  bracket (Item No. 2) and fasten into place with two screws (Item No. 4), ensuring  the small arm is pointed in.

2. Move to the top of the unit to install the other two plastic mounting brackets (Item No. 2) with two screws (Item No. 4).

3. At the back base of the unit, install one metal mounting bracket (Item No. 3)  by unscrewing the two existing screws, sliding into place and re-screwing both screws. Unscrew the same two screws on the other unit and set aside for later.

INSTALLATION

CONNECT UPPER BRACKETS TO CONNECT THE REFRIGERATORS

1. Realign both refrigerators so they are flush and line up with the opening where  they will be installed.
2. Finish installing the plastic mounting bracket on the back with the other two screws to connect both units. Do the same with both brackets on top.

CONNECT LOWER BRACKETS TO CONNECT THE REFRIGERATORS

1. At the back base of the unit, finish installing the metal lower bracket by screwing  in the two screws set aside earlier.
2. Install the second metal lower bracket on the front base of both units using the remaining four screws.

INSTALLATION

ATTACHING THE CABINET MOUNTING BRACKETS

• With both units connected, you need to install cabinet mounting brackets provided with  your RBIV-30 parts kit before you can push the dual unit into place.

• Three cabinet mounting brackets go on the outer left and right sides of the dual RBIV 60 unit, while four total brackets go on top of the dual unit — two on each RBIV-30.

• Using a screwdriver or drill with a Phillips-head bit, fasten 20 screws provided with the  Confidential RBIV-30 parts kit to secure all 10 cabinet mounting brackets to the dual unit.

• NOTE: The image below is detailed in the RBIV-30 Installation manual and shows how you would install a single RBIV unit — three brackets on each side and two on top.

F ix the cabinet-cabin connecting bracket (Item No12) to the cabinet, where 2 on the top, an every side.

Since you’re installing a dual unit into one cabinet cutout, there is no need for cabinet  mounting brackets to be installed in the middle of both units. Use screw cabinet connecting bracket (Item No11) to tighten.

INSTALLATION

PUSH INTO PLACE

1. Before pushing into place, install the necessary power and water connections  and anti-tip brackets (refer to your RBIV-30 Installation Manual).

2. Uninstall the door on the left unit and re-orientate the inside drawers and hinges so the handle to the door pulls out to the left — opposite of the door on the right unit — then reinstall the door (refer to your RBIV-30 installation manual).

3. Carefully push the dual unit into the cabinet and ensure there is a 1/8” gap on  either side.

ZLINE RBIV-30 refrigerators are top-heavy and weigh 342 pounds.
The dual unit weighs close to 700 pounds. Take care when installing
the product; two-person assembly is highly recommended.

INSTALLATION

ADJUSTING THE REFRIGERATOR HEIGHT

• With the dual unit now pushed into the cabinet, the feet need to be raised in order to  secure the product to the anti-tip brackets.

• You may use a drill with a 1/4″ hex bit or a socket wrench to adjust leg height; we  recommend using a socket wrench by hand to avoid the risk of stripping the legs.

It’s important to raise the front feet first to reduce risk of the appliance falling  frontward, which would increase the risk of injury.

A/D — Turn the key clockwise to lift the front
B/C — Turn the key clockwise to lift the rear

• After adjusting the feet, check if both RBIV-30 units are level in both width and depth  directions. You may readjust as needed after panels are installed.

• The maximum height the adjustable feet can reach is 1 9/16″ (40 mm), and the maximum product height is 85 3/8″ (2,169 mm).

INSTALLATION

SECURING THE DUAL UNIT INTO THE CABINET CUTOUT

• With the dual unit now pushed into the cabinet and perfectly level, you can finalize  flush installation be securing the cabinet mounting brackets installed on page 13.

• If you have difficulty tightening the screws, opening a reference hole with a drill will  make this procedure easier, as shown in the images below.

• Using the remaining cabinet mounting bracket screws provided with your RBIV-30  parts kit, secure the right unit to the cabinet — 4 screws on top and 6 on each side.

• After the right unit is secured into the cabinet, secure the left unit into the cabinet in the  same manner — 4 screws on top and 6 on each side.

INSTALLATION

ATTACHING THE TRIM PIECES

• Attach the side trim pieces provided with the RBIV-30 parts kit onto the outer sides  of each unit, covering the cabinet mounting brackets as shown below.

• Attach the top trim pieces provided with the RBIV-30 parts kit onto the tops of both  units, covering the cabinet mounting brackets as shown below.

INSTALLATION

INSTALL DIVIDER TRIM

• After ensuring both units are flush and everything is level, insert the center divider trim (Item No. 5 in the dual unit parts list) between both units and lightly pound  into place with the back of your fist.

INSTALLATION

INSTALLATION COMPLETE

• IMPORTANT: Refer to your RBIV-30 installation manual as needed for other installation procedures.

Scan the QR code to view the most up-to-date version of our
RBIV-30 / RBIV-36 user manual and installation manual.

WARRANTY

COVERAGE

ZLINE Kitchen and Bath built-in refrigerators have a two year parts and service warranty and  a five year parts warranty on the sealed system. This is from the original purchase date for the  original purchaser of the product.

TERMS

This warranty applies only to the original purchaser of the product installed for normal  residential use. This is defined as a single-family, residential dwelling in a non-commercial  setting.

Commercial settings include but are not limited to: schools, churches, hotels, restaurants,  vacation rentals such as Airbnb, day care centers, private clubs, fire stations, common areas  in multi-family dwellings, nursing homes, food service locations, and institutional food service  locations such as hospitals or correction facilities. This warranty is non-transferable and will not be extended based on the date of installation. The warranty applies only to products  installed in the contiguous United States and the District of Columbia.

Warranty shall not apply and ZLINE Kitchen and Bath is not responsible for damage resulting  from negligence, improper maintenance, misuse, abuse, alteration of or tampering with  the appliance, accident, natural disaster, improper electric supply, unauthorized service or  repair, improper installation, or installation not in accordance with the instructions contained  in the manual or the local government codes.

WHAT IS NOT COVERED

1. Start-up damages or problems caused by improper installation or use.

2. Damage related to unauthorized service or unauthorized parts.

3. Installation in any commercial or non-residential application.

4. Aesthetic damage, scratches, or natural wear caused by normal use.

5. Second-hand, open box products, or products purchased from an unauthorized retailer.

NOTE: In the event that service is dispatched, and it is discovered that the reported  issue is not covered under warranty based on the disclaimers above, the customer will  be responsible for all service fees. Failure to pay these fees will result in the forfeiture of  remaining warranty coverage.

WARRANTY

RATING TAG LOCATION

The rating tag shows the model and serial number of

your refrigerator. The product label and rating tag

is located on the left-hand side of the inner door of

the 30″ refrigerator and on the left-hand side of the

left-side door of the 36″ model. The tag is visible

when the refrigerator door is open. Do not remove

permanently affixed labels, warnings, or plates from

the product. This will void the warranty.

SERVICE

For warranty service, please contact our Customer Service team at

1-614-777-5004 or visit www.zlinekitchen.com/contact to utilize our

online Customer Experience Portal.

Need to purchase a part or accessory for your ZLINE product?

Visit www.zlineparts.com, ZLINE’s official parts distribution partner.

1.2.1

www.zlinekitchen.com

1-614-777-5004

contact@zlinekitchen.com

References

• P65Warnings.ca.gov
• ZLINE Kitchen and Bath Parts & Accessories
• ZLINE Product Manuals and Installation Guides – ZLINE Kitchen and Bath
• ZLINE Product Manuals and Installation Guides – ZLINE Kitchen and Bath

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>