HZY MC6 Intelligent Cloud Film Cutting Machine User Manual
- June 12, 2024
- HZY
Table of Contents
HZY MC6 Intelligent Cloud Film Cutting Machine
Product Information
The Intelligent Cloud Film Cutting Machine is a high-tech device designed for precise and efficient film cutting. It comes with a range of accessories and features that enhance its usability and performance.
Packing List:
- Smartphone
- Cutter*1
- Blade holder *1
- Blade*3
- Power adapter*1
- Scraper*1
- Power cable*1
- Warranty card*1
- Non-slip mat*1
- Cleaning cloth*1
Blade Installation:
- Press the handle to release the blade.
- Adjust the blade tip length using the gear. Twist the gear to make the tip longer or shorter.
- Fix the blade handle holder into the hole in the cutting head.
- To change the blade, press the handle and replace the old blade with a new one.
Blade Holder Installation:
- Loosen the screw by turning it counterclockwise 8 times.
- Insert the blade holder vertically into the holder’s hole.
- Tighten the screw by turning it clockwise.
Power On / Off:
Connect the power cable and adapter to a 110-240V AC power source. The
adapter connects to the machine. Press the power button to turn on the
machine. It takes approximately 30 seconds to start.
Material Installation:
Place the material flat on the table and align it to the left based on the
feeding guide. The cutter will automatically feed the material once it is
detected. If the film shifts, press the switch
for 1 second to automatically return the film back.
WIFI Connecting:
To connect to WIFI, turn on the wifi on the cutter and select a wifi
network to connect. If the connection is successful, the wifi ID will be
displayed. If not, ensure that you have entered the correct password.
Login Account:
To login to the data page, choose login after connecting to wifi. Enter
your account, version, and password. Account and password information can be
found at the bottom of the cutter or
obtained from your supplier.
Choose Cutting Data:
Once logged in, enter the product page and choose the specific data you
need to cut.
Choose a Cutting Data:
Select the desired cutting data based on the type of product or brand you
are working with. Please refer to the user manual for further details and
instructions on using the Intelligent Cloud Film Cutting Machine.
Packing list
-
Cutter carriage
Control the blade to cut the film sheet -
Rubber wheels
Work with steel axis to keep cutting without slip -
Steel axis
Work with rubber wheels to fix and protect film sheet -
Power switch
Turn on the machine . Press it lightly to turn back the films during stand-by -
Blade holder
Install the blade to cut the film sheet -
Film feeding sensor
Auto feeding the film after detecting it -
Right baffle
Used along with left baffle to keep film sheet without shift -
Left baffle
Used along with right baffle to keep film sheet without shift -
High definition screen
6 inch touch screen , built in operation system -
Roller handle
Press handle and the roller will put up , then the roller can be moved
Blade installation -
Handle
Press it to get the blade -
Gear
Adjust the blade tip length -
Blade handle holder
To be fixed by the hole in cutting head -
Cutting Blade
Cutting film sheet
Notes:
- Adjust the blade:
- Twist the gear to adjust the blade tip
- Value bigger, tip longer
- Value smaller, tip shorter
- Factory setting is gear 6
- Change blade:
- Press handle take out the old blade,put a new one in it
Blade holder installation
-
loose the screw
Turn the screw counterclockwise in 8 times -
Insert the blade holder
The baled holder with the cutting blade is placed vertically into the holder’s hole． -
Fix the screw
Turn the screw in clockwise．
Power on / off
- Connect the cable and adapter.
- 110-240V AC power for the plug connection.
- The adapter connects the machine.
- Press the power button, machine power on. It takes 30s for starting.
Material installation
- Put the material on the table flatly and align left based on the feeding guide The material will be feed automatically after the cutter detect it.
- (If the film shift, press the switch in 1 second and the film will be returned back automatically)
WIFI Connecting
- After turn on the wifi on the cutter, click and choose a wifi to connect.
- Note: Connecting succeed, the wifi ID will be showed below if not, you may need insert the correct password and connect. .
Login account
- After connecting wifi, choose login and insert the account and choose version, then insert your password to login the data page..
- Account and password mav paste on the bottom ofthe cutter or you can get from your supplier
Choose Cutting Data
After enter the product page
and choose the data you need to cut
Choose a cutting data
- Front film -A+ is accurate data, the front screen is wrapped to the edge of the screen; -A is slightly smaller than At by about 0. 5mm – with cover A is the data with cover; – Frosted A is the hole data, suitable for frosted/matte materials..
- Back film -B+ is back film with full cover, -B- is back film packaging data; -B is back sticker data
- The explosion-proof film is only suitable for straight screen mobile phones, the size is similar to the tempered glass.
- Full-screen film-DA full-screen half-package data, -DB back-stick data; -DC is the whole machine full-package data
Cutting finished
The sheet will be dropped out
automatically after cutting finished, please take out the finished parts and
paste on the phone.
Parameters and precautions
Parameters
Connection| wifi or Bluetooth
Internal Power| DC 24 V 1 . 75 A
Screen size| 6 . 0 inches
machine size| 594 284 290 mm
machine weight| 6 . 5 kg
- Don’t touch the knife tip by finger
- The finger may be hurt by the knife tip
- Don’t seep into liquid
- This may cause fire or electric shock
- Don’t + use non-original power supply
- This may damage the circuit or electric shock
- Don’t use in thunderstorm days
- This may damage the machine
- Don’t use the non-standard materials
- Please cut the standard size of material to reach the perfect result
Press power switch for emergency stop during working..
Forbid moving the carriage by hand after connecting the power to avoid machine
damage.
Knife is a consumable part, please change to a new one if it is dull..
Press the power switch in 3 seconds continually to turn off the cutter, forbid
taking out the power cable directly to turn off the machine because it will
damage the mainboard
Troubleshooting
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
- These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
- However there is no guarantee that interference will not occur in a particular installation.
- If this equipment does cause harmful interference to radio or television reception.
- which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body
- Use only the supplied antenna