SelectBlinds ABC-01 Panel Track with Motorization Installation Guide

SelectBlinds panel track with motorization

Installation – panel track with motorization

WARNING

• Young children can suffocate in the loop of pull cords, chains and tapes, as well as cords that operate window coverings.

• To avoid strangulation and entanglement, keep cords out of the reach of small children.
  Cords can wrap around the child’s neck

• Move beds, cribs and furniture away from window covering cords.

• Do not tie the strings together.
  Make sure that the cords do not twist together and form a loop.

Control

Take care that the blinds can move freely and are not obstructed by any objects.

Manual remote control

WARNING:  Important safety instructions. Follow all instructions as improper installation can cause serious injury.

WARNING:  Do not repair by yourself. Do not attempt to open or disassemble the device. You risk electric shock and void your limited warranty. There are no user serviceable parts inside.

General information

Performances

ABC-01

• Battery CR2032 1.5V
• channels 5
• Max. blinds to channel endlessly
• Range (inside the building) 20m, 2 concrete walls
• Frequency 2.4 GHz
• Weight 56 ​​grams

Buttons

Battery replacement

Programming

To program the blind:

1. Set blind in program mode, chapter 2.1
2. Program the blind, 2.2. department
3. Exit the program mode, 2.1. department

Set the blind in program mode

Blind setting in program mode can be done in three ways. If the blind is in program mode, it will show step motion. The blinds can still be operated with buttons. If the program operation is confirmed, the blind stops climbing for 3 seconds. The blind automatically exits the program mode after 4 minutes.

1. By hand: press the program button on the blind.
   In program mode, it is possible to set several blinds and program them simultaneously.

2. By remote control: SingleSelect mode
   SingleSelect mode is a patented method to set the blind in program mode by remote control. When the remote control and blind are in SingleSelect mode, the blind can be operated, paired with one or more channels, and programmed.
   The other blinds are disconnected from the remote control until the SingleSelect mode is over.

3. With Remote Control: ChannelSelect
   ChannelSelect is a method to put all blinds paired on the same channel into program mode.

Shutter programming

1. Pair a blind with a channel
   To pair a blind with a channel, the blind must be in program mode.
   See 2.1. chapter on how to set the blind in program mode and exit program mode.

2. Connect multiple blinds simultaneously to a channel or another remote control
   To connect multiple blinds simultaneously to a channel or another remote control, all blinds must be in program mode. See 2.1. chapter on how to set the blind in program mode and exit program mode. Pairing multiple blinds to a channel at the same time is not possible with Singleselect

3. Set favorite position
   To program the blind, the blind must be in programming mode.
   See 2.1. chapter on how to set the blind in program mode and exit program mode.

4. A. Switch the blind’s direction of rotation
   To program the blind, the blind must be in programming mode. See 2.1. chapter on how to set the blind in program mode and exit program mode.
   Example: when you press the remote control left/down and the blind moves right/up, you need to change the direction of rotation of the blind.

5. B. SingleSelect Mode: Switch the rotation direction of the panel and vertical blinds

6. Setting blinds in battery mode (green mode)
   To program the blind, the blind must be in programming mode. Important: BatteryMode can only be turned on using the SingleSelect method, see 2.1. chapter on how to set the blind in program mode and exit program mode with one selection.
   The RF device in the blind transmits radio signals to increase the range of the remote control.

At work

Select a channel

Operate the blind

Short press the buttons to make small movements, press the buttons for 2 seconds and the blind will move automatically. Press the stop/center button to stop the movement. Buttons

Remote control holder

Safety and cleaning

Safety

WARNING:
Do not repair by yourself. Do not attempt to open or disassemble the device. You risk electric shock and void your limited warranty. There are no user serviceable parts inside.

• Do not allow children to play with the blinds and/or the remote control
• Do not paint the device
• Keep the device dry. Precipitation, moisture, and all kinds of liquids or moisture can contain minerals that corrode electronic circuits. If the device gets wet, remove the battery and allow the device to dry completely before replacing the battery.
• Do not drop, hit or shake the device. Rough handling can break internal circuit boards.

cleaning

When cleaning the exterior of the device and its components, follow these general rules:

• Make sure the device is unplugged.
• Use a soft, lint-free fabric. Avoid getting moisture into the openings.
• Do not use aerosol sprays, solvents, alcohol or abrasives.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>