hager TYFS110 Power Supply Instructions

: June 12, 2024
: hager

Table of Contents

hager TYFS110 Power Supply
Installation instructions
Technical characteristics
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hager TYFS110 Power Supply

hager-TYFS110-Power-Supply-product

Product Information

Model: TYFS110 – Input Voltage: 200-240V AC 50/60Hz
Output Voltage: 30V DC – Output Current: 1280mA – Power
Dissipation: 6.4W – Dimensions: Not specified – Degree of
Protection: Not specified – Operating Temperature: Not specified –
Storage Temperature: Not specified – Consumption without Load: Not
specified – Efficiency: Not specified – Pollution Category: Not
specified – Overvoltage Category: Not specified – Dielectric
Strength: Not specified – Operating Altitude: Not specified –
Signaling Contact: Not Specified Product Usage Instructions: 1.
Connect the power supply to the input terminal of the device using a 200-240V AC 50/60Hz power source.
Connect the load to the output terminal of the device.
Ensure that the input voltage does not exceed 240-250V DC or the output current does not exceed 1280mA to prevent damage to the device.
The device is designed for use with a KNX bus system. Connect the device to the KNX bus using the appropriate connectors.
The LED indicators on the device provide status information. The LED labeled “RESET” indicates the reset function.
If the LED labeled “RESET” is flashing at a frequency of 2.5Hz, it indicates a bus KNX (C2) reset.
If the LED labeled “RESET” is flashing at a frequency of 0.25Hz, it indicates a bus KNX (C2) reset with a delay of 20 seconds.
The device has a signaling contact for additional functionality. Please refer to the user manual for detailed instructions on how to use the signaling contact.
Note: The user manual may provide additional information and instructions specific to your application.

The power supply TYFS110 generates a 30V DC voltage. The system-generated voltage meets the requirements of the protection measures SELV (Safety Extra- Low Voltage). The product has 2 outputs: 1 nonfiltered output 30V DC (C1) and 1 filtered 30V DC KNX output (C2). The module must be installed on an electrical board that provides mechanical, electrical, and fire protection.

Installation instructions

Connect the module to the mains and to the load.
The OK indicator lights up in normal working mode.
The power supply must be equipped with a circuit breaker protecting both poles connected to the module.
If a max” or “U> Umax” indicator lights up, correct the origin of the default (max short-circuit, or U>Umax overload).
A short press on the RESET button clears the default and turns off the corresponding LED.

Temporary RESET
Pressing the RESET button for 2s<<4s cut off the KNX Bus output (C2) for 20 seconds. In this state, the RESET LED flashes rapidly (2.5 Hz). After 20 seconds the product returns to normal
operation and the RESET LED turns off.

Permanent RESET
Pressing the RESET button for t>4s cuts off the KNX Bus output (C2) permanently. In this state, the RESET LED flashes slowly (0.25 Hz). A short press t<0.5s on the RESET button allows the product to return to normal operation and the RESET LED to turn off.

The device must only be installed by a qualified electrician according to the installation standards applicable in the country.| Conform TBTS installation rules. The parallel connection of two 1280 mA power supplies in the same KNX line is not permitted, because the maximum permissible current in this line (KNX Handbook: max. 3 A) is exceeded. Correct Disposal of this product Waste Electrical & Electronic Equipment). (Applicable in the European Union and other European countries with separate collection systems. The marking shown on the waste or its literature indicates math should not be disposed of with other households wasting the end of its working too.

To prevent possible harm to the environment or human health from uncontrolled waste disposal. phone separate this product from other types of waste and recycle it responsive to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product, or their local government office, for details on safe recycling.
Business users should contact them sooner and check the tells and conditions of the purchase contract. This product should not be mixed vain other commercial wastes at the disposal ( € Product complies with European legislation

Name and content of hazardous substances in products: This table is prepared in accordance with the provisions of SU/T 11364

indicators that said hazardous substance contained in all of the homogeneous materials for this part is below the limit reg
indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is abr
Indicates that a hazardous substance contained in at least one of the homogeneous materials used for this part is aoc

For indoor use only. Electrical equipment designed primarily for indoor use.
Overvoltage categorv installation.
The equipment incorporates a short-circuit-proof safety isolating transformer.

Class II equipment.
Alternating current or voltage.

Direct current or voltage.Switch mode power supply unit.

The Regulatory Compliance Mark (RCM) is a trademark owned by the electrical regulator (Regulatory Authorities (As)) and Australian Communications Media Authority (ACMA). China RoHS logo.

Equipment containing certain substances that are forbidden under the China RoHS directive, but which can be used with complete safety during the environmental protection normed.

This period is indicated by the number in the loco engrossed indoors