HITACHI L32A01 Flat Digital TV Instruction Manual
- June 12, 2024
- Hitachi
Table of Contents
Instruction Manual
FLAT DIGITAL TV
L32A01 Flat Digital TV
Quick Start Guide
-
Insert the batteries into the Remote Control
Insert wo AAA/R3 or equivalent type batteries inside.
Observe the correct polarity (+/-) when inserting batteries and replace the battery cover. -
Connect the antenna to your TV
-
The back connection options may differ depending on the model 3. Connect the TV to the mains socket 4. To switch the TV on (depending on the model)
After connecting the power cord to the mains socket, the standby LED lights up.
To switch on the TV from standby mode either;
1. Press the Standby button, a numeric button or Programme +¢/- button on the remote control. —-— OF -—-——
2. Press the side function switch on the TV until the TV comes on from Standby. -
The appearance of the remote control butions and the position of the control buttons on the TV may differ depending on the model 5. HDMI input
PLEASE ENSURE BOTH UNITS ARE SWITCHED OFF BEFORE CONNECTING. Use a HDMI to HDMI cable to connect the two units together. To select the HDMI input, press the Source button on the remote control. Each time it is pressed the on-screen menu confirms your selection.
• The appearance of the Source button may differ depending on the model of the remote control ****-
Auto Setup procedure (depending on the model)
When turned on for the first time, the language selection screen is displayed. Select the desired language and press OK. You will be asked whether you want to change accessibility settings. Make your selection press OK to continue. On the next screen set your country preference. Then press OK to continue. Select Home Mode for home use. You can activate Store Mode option at this point if necessary, however, this option is only intended for store use. Depending on the model of your TV and the country selection Privacy Settings menu may appear at this point. Using this menu you can set your privacy privileges. Highlight a feature and use Left and Right directional buttons to enable or disable. If the Internet Connection option is disabled Network/Internet Settings screen will be skipped and not displayed. Highlight Next and press OK button on the remote control to continue and the NetworklIntemet Settings menu will be displayed. Refer to Connect your TV to the internet section to configure a wired or a wireless connection. After the settings are completed highlight Next and press OK button to continue.
Broadcast Search; On the next screen set your preferences.
Scan Encrypted Channels On Select favourite network type
on
Satellite
D.Aerial D.Ο
Cable SatelliteΟ
Analogue∎
When finished, highlight Next and press OK to start channel scan. After the initial settings are completed TV will start to search for available broadcasts of the selected broadcast types. While the search continues a message may appear, asking whether you want to sort channels according to the LC N(“). Select Yes and press OK to confirm. (*) LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel number sequence (if available). After the channel scan has been completed the Choose Region menu may appear. Select the appropriate settings for your location using the directional buttons then press OK. After all the available stations are stored, Channels menu will be displayed. You can edit the channel list according to your preferences using the Edit tab options or press the Menu button to quit and watch TV. Note: Do not turn off the TV while initializing first time installation. Note that, some options may not be available depending on the country selection. -
Connect your TV to the Internet
Connectivity feature allows you to connect your TV to the home network wired or wirelessly. You can use this networking system to connect to internet or to access photo, video and audio files that are stored on a Media server connected to the network and play/display them on the TV.
However, if your TV does not have Wireless USB dongle or doesn’t support intemal WLAN feature, you should use wired connection type. Add your TV to your home network by connecting it to the modem/router via an LAN cable (not supplied) as illustrated.
To use your TV with your wireless network, you may need a WLAN USB dongle. You should connect it to one of the USB inputs on the TV. If your TV supports intemal WLAN feature you won’t need a wireless LAN adaptor.
Press the Menu button to open the main TV menu. Select Settings by using the directional buttons, highlight Network and press OK. While Network Type is highlighted, press Left or Right buttons to select connection type. Wired connection will be established automatically. If wireless connection is selected, highlight Scan Wireless Networks and press OK. The TV will search for the available wireless networks and list them when finished. Select one and press the OK button to connect. If the wireless network is password- protected you should enter the correct password to access the network.
Note: For more detailed information refer to the manual installed on your TV. To access this manual, enter Settings menu. select Manuals and press OK. For quick access press Menu button and then Info button.
-
Accessories Included
- Remote Control
- Batteries: 2 x AAA
- Quick Start Guide Depancin on model
- Side AV Connection Cable
- YPbPr Connection Cable
- WLAN USB Dongle and USB Extension Cable
- Wall Mount Kit
- DC 12 V Input Power Adaptor
- Car Plug
Safety Information
In extreme weather (storms. lightning) and long inactivity periods (going on
holiday) disconnect the TV set from the mains. The mains plug is used to
disconnect TV set fran the mains and therefore it must remain readily
operable. If the TV set is not disconnecled electrically from the mains. the
device will sal draw power for a situations even if the TV is in standby mode
or switched off. Note: FOROW the On Street) liLttfUalOnS fa OpaINIng the Wad
tea twos.
IMPORTANT -Please readthese Instructions fully before installing or
operating
WARNING: This device is Intended to be used by persons (including
children) who are capable / experienced of operating such a device
unsupervised, unless they have been given supervision or instruction
concerning the use of the device by a person responsible for their safety.
-
Use this N set at an attitude of less than 5000 meters above the sea level, in dry locations and in regions with moderate or tropical climates.
-
The TV set is intended for household and similar indoor use but may also be used in public places.
-
For ventilation purposes, leave at least Scm of free space around the TV.
-
The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains. etc.
-
The power cad plug should be easily accessible. Do not place the N. furniture, etc. on the power cord. A damaged power cord/plug can cause fire or give
you an electric shock. Handle the power cord by the plug, do not unplug the N by pulling the power cord. Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock. Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this should only be done by qualified personnel. -
Do not expose the TV to dripping or splashing of liquids and do not place objects filled with liquids, such as vases, cups, etc. on or over the TV (e.g.. on shelves above the unit).
-
Do not expose the N to direct sunlight or do not place open flames such as lit candles on the top of or near the TV.
-
Do not place any heat sources such as electric heaters, radiators, etc. near the TV set.
-
Do not place the N on the floor and inclined surfaces.
-
To avoid danger of suffocation, keep plastic bags out of the reach of the babies. children and domestic animals.
-
Carefully attach the stand to the TV. If the stand is provided with screws, tighten the screws firmly to prevent the N from titling. Do not over-tighten the screws and mount the stand rubbers properly.
-
Do not dispose of the batteries in fire or with hazardous or flammable materials.
WARNING – Batteries must not be exposed to excessive heat such as
sunshine, fire or the like.
WARNING-Excessive sound pressure from earphones or headphones can cause
hearing loss.
ABOVE ALL – NEVER let anyone, especially children, push or hit the screen,
push anything Into holes, slots or any other openings in the case.
Caution | Serious injury or death Ask |
---|---|
Risk of electric shock | Dangerous voltage Fisk |
Maintenance | Important maintenance component |
Markings on the Product
The following symbols are used on the product as a marker for restrictions and
precautions and safety ‘nstructions.
Each explanation shall be considered where the product bears related marking
only. Note such information for security reasons. ‘
** Class II Equipment: This appliance is designed in such a way that it
does not require a safety connection to electrical earth.
Hazardous Live Terminal: The marked terminal(s) is/are hazardous live under
normal operating conditions. Caution, See Operating Instructions: The marked
area(s) contain(s) user replaceable coin or button cell batteries.
Class 1 Laser Product: This product contains Class 1 laser source that is safe
under reasonably foreseeable conditions of operation.
WARNING** Do not ingest the battery. Chemical Burn Hazard This product or
the accessories supplied with the product may contain a coin/button cell
battery. If the coin/button cell battery is swallowed, it can cause severe
internal bums in just 2 hours and can lead to death. Keep new and used
batteries away from children. If the battery compartment does not close
securely. stop using the product and keep it away from children. If you think
batteries might have been swallowed or placed inside any part of the body.
seek immediate medical attention.
A television may fall, causing serious personal injury or death. Many
injuries. particularly to children, can be avoided by taking simple
precautions such as:
- ALWAYS use cabinets or stands or mounting methods recommended by the manufacturer of the television set.
- ALWAYS use furniture that can safety support the television set.
- ALWAYS ensure the television set is not overhanging the edge of the supporting furniture.
- ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls.
- ALWAYS route cords and cables connected to your television so they cannot be tripped over. pulled or grabbed.
- NEVER place a television set in an unstable location.
- NEVER place the television set on tall furniture (for example. cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.
- NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture.
- NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which the television is placed.
- The equipment is only suitable for mounting at heights 52 m. If the existing television set is going to be retained and relocated, the same considerations as above should be applied.
Apparatus connected to the protective earthing of the building installation through the MAINS connection or through other apparatus with a connection to protective
earthing- and to a television distribution system using coaxial cable. may in some circumstances create a fire hazard. Connection to a television distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator)
WALL MOUNTING WARNINGS
- Read the instructions before mounting your TV on the wall.
- The wall mount kit is optional. You can obtain from your local dealer, if not supplied with your TV.
- Do not install the TV on a ceiling or on an inclined wall.
- Use the specified wall mounting screws and other accessories.
- lighten the wall mounting screws firmly to prevent the TV from fall. Do not over-tighten the screws.
License Notification
The terms HDMI. HDMI High-Definition Multimedia nterface. and the HDMI Logo
are trademarks or registered trademarks of HDMI LicensivAdirinistrator Inc.
Manufactured under license from Dolby Laboratories. Dolby. Dolby Audio, and
the double- D symbol are trademarks of Dolby Laboratories Licensing
Corporation . YouTube and the YouTube logo are trademarks of Google Inc. This
product contains technology subject to certain intellectual property rights of
Microsoft. Use or distribution of this technology outside of this product is
prohibited without the appropriate license(s) from Microsoft. Content owners
use Microsoft PlayReady”‘ content access technology to protect their
intellectual property, including copyrighted content. This device uses
PlayReady technology to access PlayReady-protected content and/or WMDRM-
protected content. If the device fails to properly enforce restrictions on
content usage. content owners may require Microsoft to revoke the device’s
ability to consume PlayReady-protected content. Revocation should not affect
unprotected content or content protected by other content access technologies.
Content owners may require you to upgrade PlayReady to access their content.
If you decline an upgrade, you will not be able to access content that
requires the upgrade. The ‘CI Plus” Logo is a trademark of CI Plus LLP.
This product is protected by certain intellectual property rights of Microsoft
Corporation. Use or distribution of such technology outside of this product is
prohibited without a license from Microsoft or an authorized Microsoft
subsidiary. Depend.; on mnde( For DTS patents, see
http://patents.dts.com. Manufactured under license
from DTS Licensing Limited. DTS. the Symbol. DTS and the Symbol together. DTS-
HD. and the DTS-HD logo are registered trademarks or trademarks of DTS, Inc.
in the United States and/or other countries. 0 DTS. Inc. All Rights Reserved.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS Licensing Limited. DTS. the Symbol. DTS and the Symbol together.
Virtual:X. and the DTS Virtual:X logo are registered trademarks or trademarks
of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All
Rights Reserved.
Wireless LAN Transmitter Specifications
Wireless LAN Transmitter Specifications|
---|---
Frequency Ranges| Max Output Power
2400 – 2483.5 MHz (CHI-CH13)| < 100 mW
5150 – 5250 MHz (CH36 – CH48)| < 200 mW
5250 – 5350 MHz (CH52 – CH64)| < 200 mW
5470 – 5725 MHz (CH100 – CH140)| <200 mW
Country Restrictions
This device is intended for home and office use in all EU countries (and other
countries following the rele-vant EU directive) without any limitation except
for the countries mentioned below.
Country Restriction Bulgaria General authorization required for outdoor use
and public service Italy If used outside of own premises, general
authorization is required Greece In-door use only for 5470 MHz to 5725 MHz
band Luxembourg General authorization required for network and service
supply(not for spectrum)
Country | Restriction |
---|---|
Bulgaria | General authorization required for outdoor use and public service |
Italy | If used outside of own premises, general authorization is required |
Greece | In-door use only for 5470 MHz to 5725 MHz band |
Luxembourg | General authorization required for network and service supply(not |
for spectrum)
|
Country| Restriction
Norway| Radio transmission is prohibited for the geographical area within a
radius of 20 km from the centre of Ny-sNesund
Russian Federation| In-door use only
Israel| 5 GHz band only for 5180 MHz-5320 MHz range
The requirements for any country may change at any time. It’s recommended that user checks with loca authorities for the current status of their national reg ulations for 5 GHz wireless LAN’s.
Disposal Information
[European Union]
These symbols indicate that the electrical and electronic equipment and the
battery with this symbol should not be disposed of as general household waste
at its end-of-life. Instead, the products should be handed over to the
applicable collection points for the recycling of electrical and electronic
equipment as well as batteries for proper treatment, recovery and recycling in
accordance with your national legislation and the Directive 2012/19/EU and
2013/56/EU. By disposing of these products correctly. you will help to
conserve natural resources and will help to prevent potential negative effects
on the environment and human health which could otherwise be caused by
inappropriate waste handling of these products. For more information about
collection points and recycling of these products. please contact your local
municipal office, your household waste disposal service or the shop where you
purchased the product. Penalties may be applicable for incorrect disposal of
this waste, in accordance with national legislation. [Business users] If you
wish to dispose of this product, please contact your supplier and check the
terms and conditions of the purchase contract. [Other Countries outside the
European Union] These symbols are only valid in the European Union. Contact
your local authority to learn about disposal and recycling. The product and
packaging should be taken to your local collection point for recycling. Some
collection points accept products free of charge. Note: The sign Pb below the
symbol for batteries indicates that this battery contains lead.
Mobile TV Instructions (Depends on model)
Switching the IV On Using 12 Volt 1. Connect the cigarette lighter plug cable
to the cigarette lighter socket of your car or a cable with clips to the
battery of car. making sure to observe the correct polarity. 2. Plug the other
side of 12 volt cable to DC 12V socket at the back of the TV. 3. Press Power
On/Off button. Then the TV switches itself to stand-by mode.
Switching the TV Off 1. Press the Standby button on the remote control. 2.
Unplug cable connectors and power plugs.
ATTENTION: 12 V Input
Remote Control
(• MY BUTTON 1:
This button may have default function depending on the model. However you can
set a special function to this button by pressing on it for five seconds when
on a desired source or channel. A confirmation message will be displayed on
the screen. Now the My Button 1 is associated with the selected function. Note
that if you perform First Time Installation. My Button 1 will return to its
default function.
- Standby: Switches On / Off the TV
- Numeric buttons: Switches the channel, enters a number or a letter in the text box on the screen
- Language: Switches among sound modes (an-alogue TV), displays and changes audio/subtitle language and turns subtitles on or off (digital TV. where available)
- Mute: Completely turns off the volume of the N
- Volume –
- Menu: Displays TV menu
- Guide: Displays the electronic programme guide
- Directional buttons: Helps navigate menus. content etc. and displays the subpages in TXT mode when pressed Right or Left
- OK: Confirms user selections, holds the page (in TXT mode), views Channels menu (DTV mode)
- Backiftetum:Retums to previous screen, previous menu, opens index page (n TXT mode). Quickly cycles between previous and current channels Or sources
- Netfllx: Launches the Netflix application
- My Button 1 (•)
- Coloured Buttons: Follow the on-screen instruc-tions for coloured button functions
- Rewind: Moves frames backwards in media such as movies
- Record: Records programmes
- Play: Starts to play selected media
- Pause: Pauses the media being played, starts timeshift recording
- Stop: Stops the media being played
- Fast Forward: Moves frames forward in media such as movies
- . Prime Video: Launches the Amazon Prime Video application
- YouTube: Launches the YouTube application
- Exit. Closes and exits from displayed menus or returns to previous screen
- Info: Displays Eformation about on-screen content, shows hidden information (reveal – in TXT mode)
- Source: Shows available broadcast and content sources
- Programme +1-
- . Text: Displays teletext (where available), press again to superimpose the teletext over a normal broadcast picture (mix)
Product name:|
---|---
Tipusa: Type:|
Serial number:|
Termek bruttO fogyasztoi era:|
termek atadasanak
Date of purchase/ handover I installation:|
Customer’s name and address:|
Name and address / stamp of business (seller):|
| 1| 2| 3
---|---|---|---
Announcement date| | |
Return date| | |
Bejelentett hiba Declared error| | |
Javitas madja Type of reparation| | |
..16taIlas Cij hatarideje Date of new warranty| | |
Munkalapszarn Worksheet number| | |
.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>