JFA Eletr nicos Controle K1200 Controle Longa Distancia Instruction Manual

JFA Eletr nicos Controle K1200 Controle Longa Distancia

Product Information

The product is a Code IR player and unit receiver manufactured by JFA Eletronicos. It is designed for remote control operation andcan be used with compatible devices.

Product Usage Instructions

1. Make sure that the Code IR player and unit receiver are properly connected to the compatible device.
2. Ensure that the device you wish to control with the remote iswithin the range of the Code IR player.
3. Press the appropriate keys on the remote control simultaneously to perform specific functions.
4. If mentioned in the user manual, refer to the specific keys that need to be pressed simultaneously for certain operations.
5. For additional information or troubleshooting, refer to theuser manual provided with the product.

Note: For any further assistance or inquiries, you can visitjfaeletronicos.com, contact @jfaeletronicos on Twitter, or reach out to jfa eletronicos via email.

DESCRIPTION

The K1200 allows you to control by distance the main functions of the “player” and change music, folder, volume, pause, play and power.

OPERATION

• Transmitter unit: whenever you press a key, the blue LED will light up, indicating transmission.
• Receptor unit: the “led action” will turn on indicating the presence of a received signal.

NOTE

• The central will not work if the coding procedure is not performed.
• Check the light intensity of the transmitting unit LED. If it is weak or does not light, replace the battery.

1For a longer range, install the equipment in a location where the antenna is free and the most exposed as possible, the distance achieved is 1200 meters in open area.

BASIC COMMANDS TRANSMITTER UNIT

1. Volume control ( + );
2. Volume control ( _ );
3. Rewind the music;
4. Advance the music;
5.  LED indicator;
6. Go up the folder;
7.  Go down the folder;
8. Play/ pause/ ATT;
9. Power/ function (switches to aux, CD, USB, radio, etc.).

BASIC COMMANDS OF THE RECEIVER UNIT

1. RF receiver antenna;
2. LED action, reception indicator;
3. LEARN MODE key;
4. MEMORY MODE switch;
5. Code IR (see learn mode)a;
6. 12V power (black white stripe) and GND (black);
7. Infrared emitter (aim at the front of the player).

ENCODING THE CONTROL

LEARN MODE:
(Learning the functions of the original control)

1. Press the “A” key (note 1) the Led action will be constantly on;
2. Press the key of the k1200 Control (note 2),that you want to record until the “Led action” stay flashing;
3. Point the original player control to the IR code entry and press the key you want to record (note 4) until the LED action flashes quickly, and then be constantly on;
4. Repeat steps 2 and 3 for the other keys;
5. After finishing this process press the key “A” (Note 1) of the receptor or wait 10 seconds to exit the mode.

MEMORY MODE:

(The receptor has stored in its memory codes the main models of “player” (see the attached index or on the website: www.jfaeletronicos.com)).

1. Press the “M” key (Note 3), the LED action will be constantly on;
2. Press the key on the control (note. 2) corresponding to the model of the “player”, as the index, for example: to program the CD SDNY. you should perform step 1, then press the keys in sequence, in the control . Check that the LED will flash one time and then 4 times, indicating that was programmed the model 14 (Sony).
3. After finishing this process press the key “M” (note 3) of receptor or wait 10 seconds to exit the mode.

SETTING LEARN MODE AND MEMORY MODE

MEMORY MODE ENCODING

NOTE: Keys that must be pressed simultaneously:

NOTE: Keys that must be pressed simultaneously

RECOMMENDED RECEIVER INSTALLATION

The installation of the equipment in the sound system is done through a polarized power cable. Make sure the white-striped wire from the receiverunit is connected to the battery’s direct positive (+12V) and the black wire to the negative (GND).
The receiving unit should preferably be fixed away from metal parts and the car’s bodywork (which degrades the transmission) keeping, whenever possible, the antenna unobstructed to allow the greatest possible range ofthe equipment.
Position the infrared emitter, from the receiver unit aimed at the player’s panel, so that there are no obstacles between them. It is recommended to install the receiver unit in the trunk and the IR emitter in the center of the rear window, pointing towards the front of the player. Make sure the wires are not crushed in the installation process.

RECOMMENDATIONS AND NOTES

1. Install the receptor unit at least 1 meter of the Alarms central orelectronic injection module. It is recommended to install receptor in the trunk and the infrared emitting in the rear seat pointing to the front of the “CD player”.
2. For greater range should keep the antenna stretched and in a location that is visual and away from the car bodywork.
3. supply the receiving unit with 12V.
4. The receptor can operate with two transmitters; for this, performing steps 1 and 2 to the new transmitter. This feature is recommended for customers using the Slim control on the steering wheel and a K1200 to control by distance from the player.

TECHNICAL SPECIFICATIONS

“This equipment operates on a secondary basis, have not the right of protection against armful interference, even of the same type of station, and notmay cause interference to systems operating in primary basis. ”

jfaeletronicos.com

References

• JFA Eletrônicos - Automotivo e Telecomunicações -

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>