calvert 2302 Electric Labware Drying Rack Instructions
- June 12, 2024
- calvert
Table of Contents
Calvert 2302 Electric Labware Drying Rack
Product Information
The product is a bench mount unit designed to dry laboratory glassware quickly and safely. It provides continuous warm air circulation through drying pegs, ensuring that the labware is never too hot to handle. The unit operates on 230VAC, 50HZ, and consumes 431 Watts of power. It comes with three sizes of pegs to accept glassware.
Product Usage Instructions
- Turn the main power switch and heat control OFF.
- Plug the line cord into an appropriate 230 VAC outlet with a suitable adapter (not included).
- Turn the main power switch ON; the pilot light should come on.
- Adjust the heat control as desired.
- Invert the glassware and place it on the pegs.
It is important to locate the unit in a way that allows easy access to the AC plug for disconnecting power in case of an emergency. The user should be aware that using the equipment in a manner not specified by the manufacturer may impair the equipment’s protection.
Pegs & Plugs
On each panel, arrange the pegs from small on the top rows to large on the bottom rows. For multipanel units, position small pegs on upper panels and large pegs on lower panels. Plugs are provided to cover holes where no pegs are desired. Baskets are provided to hold spare unused pegs and plugs.
Maintenance
The dust filter, mounted at the underside of the base, should be cleaned once a month (115 hours of operation) by vacuuming. To remove the filter, snap off its holder.
Replacement Parts
- Part No. 99932-1563: Dust Filter & Holder
- Part No. 18931-0001: Bag of 19 Small Pegs & 6 Plugs
- Part No. 18931-0002: Bag of 19 Medium Pegs & 6 Plugs
- Part No. 18931-0003: Bag of 19 Large Pegs & 6 Plugs
The symbol indicates that this is a Class II or double-insulated electrical appliance. It does not require a safety connection to the electrical earth.
For further information or support, contact:
Phone: 1.888.610.7664
Website: www.calcert.com
Email: sales@calcert.com
INSTRUCTIONS
CONTROLS:
- Main Power Switch: Push-button with integral pilot light.
- Heat Control: Stepless time proportional controller.
- Circuit Breaker: 250VAC/50VDC, 8A
OPERATION:
- Turn the main power switch and heat control OFF. Plug the line cord into an appropriate outlet. Turn the main power switch to ON; the pilot light should come on.
- Adjust heat control as desired. Invert glassware and place it on pegs.
PEGS & PLUGS:
- On each panel, pegs should be arranged from small on the top rows to large on the bottom rows. On multipanel units, position small pegs on upper panels and large pegs on lower panels. Plugs are provided to cover holes where no pegs are desired. Baskets are provided to hold spare unused pegs and plugs.
MAINTENANCE:
- The dust filter, which is mounted at the underside of the base, should be cleaned once a month (115 hours of operation) by vacuuming. The filter is removed by snapping off its holder.
CONTROLS:
- Main Power Switch: Push-button with integral pilot light.
- Heat Control: Stepless time proportional controller.
- Circuit Breaker: 250VAC/50VDC,4A
- POWER REQUIREMENTS: 230VAC, 50HZ, 431 Watts
OPERATION:
- Dry laboratory glassware quickly and safely with this bench mount unit. While providing continuous warm air circulation through drying pegs, labware is never too hot to handle.
- Three sizes of pegs accept glassware.
- Use only with Ambient Temperature Range from 5 °C to 40 °C.
- Indoor Use Only
- Do not place it near another heating device
- Do not place in direct sunlight
- Do not place near any explosive, hazardous, or flammable chemicals.
- Do not autoclave.
- Turn the main power switch and heat control OFF. Plug the line cord into an appropriate 230 VAC outlet with a suitable adapter (**not included). Turn the main power switch to ON; the pilot light should come on. Adjust heat control as desired. Invert glassware and place it on pegs.
- Locate the unit such that the operator will have easy access to the AC plug for disconnecting power if needed in an emergency.
- The user should be aware that, if the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. The Dryers are molded in sections and fastened with steel bolts. The unit is factory assembled and no attempt should be made to loosen the nuts
PEGS & PLUGS:
- On each panel, pegs should be arranged from small on the top rows to large on the bottom rows. On multipanel units, position small pegs on upper panels and large pegs on lower panels. Plugs are provided to cover holes where no pegs are desired. Baskets are provided to hold spare unused pegs and plugs.
MAINTENANCE:
- The dust filter, which is mounted at the underside of the base, should be cleaned once a month (115 hours of operation) by vacuuming.
- The filter is removed by snapping off its holder.
- The symbol indicates that this is a Class II or double-insulated electrical appliance. It does not require a safety connection to the electrical earth.
- Adapter to convert USA 3-pin grounded plug (type B) to local outlet type.
REPLACEMENT PARTS
Description Part No.
- Dust Filter & Holder 99932-1563
- Bag of 19 Small Pegs & 6 Plugs 18931-0001
- Bag of 19 Medium Pegs & 6 Plugs 18931-0002
- Bag of 19 Large Pegs & 6 Plugs 18931-0003
1.888.610.7664www.calcert.com sales@calcert.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>