DAYTON AUDIO Passive Ultimax 8 Inch Mini Subwoofer Kit Instruction Manual

June 12, 2024
DAYTON AUDIO

DAYTON AUDIO Passive Ultimax 8 Inch Mini Subwoofer Kit Instruction Manual
Outsunny 845-238V01 Raised Garden Planter Instruction

Thank you for purchasing the Passive Dayton Audio Ultimax 8″ mini subwoofer kit. The enclosure for this speaker kit was precision cut using CNC machinery for a tight fit to make it easy to finish. With a little time and patience, your finished product will provide years of enjoyment. Please follow these instructions for the best possible results.

Suggested tools and consumables:

Drill: Rag or paper towels
Screwdriver: Solder
Wood clamps (you can never have too many of these): Wire stripper/crimper
Sanding block and/or electric finishing sander: #8 Wood Screws
Wood glue: Polyurethane glue (Gorilla Glue)

Package contents

First, empty the contents of the package and review parts to ensure everything has been included and is in good condition. If any parts are missing or damaged, please contact our customer service department at 1-800-338-0531.

A) Dayton Audio UM8-22 8″ Ultimax DVC Subwoofer 2 Ohms Per Coi

Enclosure Components

Enclosure Components

B) Baffle
C) 2 x Side Panel
D) Back Panel
E) 2 x Top/Bottom Panel
F) Brace

Enclosure Assembly

  1. First, before gluing anything, do a dry fit of the enclosure to familiarize yourself with the parts and assembly. This will also give you a chance to ensure that all pieces have been cut properly.

  2. Next, set the enclosure parts out on a flat level surface and ensure that all pieces are free of dust and debris.

  3. Start with the Back Panel (B) lying flat with the rabbeted side up, as shown.
    Assembly Instruction

  4. Apply a small bead of glue to the inside of all joining surfaces of the Back Panel (B) and one Top/Bottom panel (E). Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).

  5. Apply a small bead of glue to the inside of all joining surfaces of one Side Panel (F) and the back and top/bottom panel assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
    Assembly Instruction

  6. Apply a small bead of glue to the inside of all joining surfaces of the Brace (E) and the back, top/bottom, and side panel assembly. Then slide in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).

  7. Apply a small bead of glue to the inside of all joining surfaces of the other Side Panel (F) and the enclosure assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).

  8. Apply a small bead of glue to the inside of all joining surfaces of the other Top/Bottom Panel (E) and the enclosure assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).

  9. Apply a small bead of glue to the inside of all joining surfaces of the Baffle (E) and the enclosure assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).

  10. Make sure that all edges are flush and securely apply clamps from side to side, top to bottom, and front to back. Apply ample pressure to ensure glue is spread evenly through each joint (some glue squeeze-out can be expected). Visually inspect all seams to make sure they are all closed tightly, you may need to relocate clamps (or add more clamps) to get a perfect fit. In most cases only 6 clamps will be needed for an enclosure this size.

  11.  Wipe away any glue squeeze-out on the outside of the enclosure with a damp rag or paper towel (excess glue on the inside is fine). Allow to dry according to the glue manufacturer’s recommendations and remove clamps.

  12. Finally, fill any open seams with wood filler or a mixture of sawdust and wood glue. Then sand all surfaces and seams until smooth. Finish enclosure to your liking. See our web page for ideas and examples.
    Assembly Instruction

  13. Locate and install your preferred power terminals (Spring terminals, binding posts, speakON connector, etc…) and internal wiring.

  14. Connect the speaker wires to the appropriate terminals on the Dayton Audio UM8-22 8″ Ultimax DVC Subwoofer (A).
    Note: The Ultimax 8″ is a dual voice coil driver with 2 ohm voice coils. Be sure you wire the driver so the final impedance load will be compatible with your amplifier.
    Wire the voice coils in parallel for a 1 ohm final load.
    Wire the voice coils in series for a 4 ohm final load.
    Wire the voice coils separately for dual 2 ohm loads.
    Although it is safe to power just one coil of the driver, we do not recommend it.

  15. Carefully set the driver into the cutout and secure using the fastener of your choice

You are now ready to enjoy your finished Passive Ultimax 8″ Mini Subwoofer!

Documents / Resources

| DAYTON AUDIO Passive Ultimax 8 Inch Mini Subwoofer Kit [pdf] Instruction Manual
UM8-22, Passive Ultimax, Passive Ultimax 8 Inch Mini Subwoofer Kit, 8 Inch Mini Subwoofer Kit, Mini Subwoofer Kit, Subwoofer Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DAYTON AUDIO User Manuals

Related Manuals