DESCO 75006 ESD Cleanroom Booties Instruction Manual

DESCO 75006 ESD Cleanroom Booties

Product Information:

The Desco ESD Cleanroom Booties are specially designed for personnel who need to be grounded via a Flooring/Footwear System according to ANSI/ESD S20.20 standards. These booties are available in different sizes to accommodate various shoe sizes.

Features:

• Blue texturized polyester with carbon mono-filament nylon upper surface
• 3/8″ wide, 18″ long polyester ribbon containing 8 electrically conductive carbon suffused fibers
• 1/4″ socket snap for secure closure at the top of the shoes
• Dual-layer rubber material with a black conductive inner layer and a dark blue dissipative outer layer bottom surface to prevent scratching or marking of the flooring
• Rtt (Tab to Bottom resistance): 5 x 10^4 to 5 x 10^6 ohms tested per ESD TR53

Product Usage Instructions:

1. Ensure that the Desco ESD Cleanroom Booties are worn by personnel who are properly grounded through a Flooring/Footwear System per ANSI/ESD S20.20.
2. Place the grounding tab of each bootie inside the person’s shoe under their foot, with the grounding tab portion at the bottom of the bootie in contact with the ESD flooring.
3. Wear the booties on both feet.
4. Before wearing the booties, test them using a footwear tester (with a lower limit of 50 kilohms and an upper limit of 35 megohms) according to ESD TR53.
5. Compliance verification should be performed prior to each use, such as at the start of each day or shift change, to ensure proper functionality.
6. If the foot grounders are worn outside the ESD-protected area, consider testing them for functionality before re-entering the ESD-protected area.

Note: Specifications and procedures are subject to change without notice. For more information and support, please refer to the contact details provided.

Description

Desco ESD Cleanroom Booties are designed to be worn by personnel grounded via a Flooring/Footwear System per ANSI/ESD S20.20.
“ESD protective flooring, used with approved footwear, may be used as an alternative to the wrist strap system for standing operations.” [ANSI/ESD S20.20 section 6.2.2.2] Desco ESD Cleanroom Booties are to be worn with grounding tab placed in the person’s
shoe under their foot with grounding tab portion at bottom of the Bootie in contact with ESD flooring. Booties are to be worn on both feet, and while worn should be tested per ESD TR53 using a footwear tester (with lower limit of 50 kilohms and 35 megohms upper limit). It is a suitable ESD footwear component in ANSI/ESD S20.20 Flooring/Footwear System tested per ANSI/ESD STM97.1.

Components

• A. Blue texturized polyester with carbon mono-filament nylon upper surface.
• B. 3/8″ wide, 18″ long polyester ribbon contains 8 electrically conductive carbon suffused fibers.
• C. 1/4” socket snap allows the bootie to be securely closed at top of shoes.
• D. Dual layer rubber material, black conductive inner layer, and dark blue dissipative outer layer bottom surface. Designed not to scratch or mark flooring
  NOTE: “Compliance verification should be performed prior to each use (daily, shift change, etc.). The accumulation of insulative materials may increase the foot grounder system resistance. If foot grounders are worn outside the ESD protected area testing for functionality before re-entry to the ESD protected area should be considered.” [ESD SP9.2 APPENDIX B – Foot Grounder Usage Guidance]

Tab to Bottom resistance:
Rtt: 5 x 104 to 5 x 106 ohms tested per ESD TR53

75006| Cleanroom Bootie, Small, 6 – 7-1/2
75007| Cleanroom Bootie, Medium, 8 – 9-1/2
75008| Cleanroom Bootie, Large, 10 -11
75009| Cleanroom Bootie, XLarge, 11-1/2 – 12-1/2
75010| Cleanroom Bootie, 2XLarge, 13 – 14
75011| Cleanroom Bootie, 3XLarge, 14-1/2 – 15-1/2

Because the actual outside dimensions of shoes vary within a size, the above sizing is approximate.
Unless specified tolerance ±10%

Specifications and procedures subject to change without notice.

CLEANROOM BOOTIE
DESCO WEST: 3651 WALNUT AVE., CHINO, CA 91710 WEB SITE: Desco.com
PHONE 909-627-8178
DESCO EAST: ONE COLGATE WAY, CANTON, MA 02021-1407
PHONE 781-821-8370

DRAWING NUMBER 75006

DATE: December 2022

References

• Desco - Static Control Products and Supplies for ESD Protection
• ESD Systems - Trustat®
• Desco - 75006 BOOTIE, CLEANROOM, SMALL
• Desco - 75007 BOOTIE, CLEANROOM, MEDIUM
• Desco - 75008 BOOTIE, CLEANROOM, LARGE
• Desco - 75009 BOOTIE, CLEANROOM, XLARGE
• Desco - 75010 BOOTIE, CLEANROOM, 2XLARGE
• Desco - 75011 BOOTIE, CLEANROOM, 3XLARGE

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>