ISLABIKES Jimi Adult Mountain Bike Owner’s Manual

: June 12, 2024
: ISLABIKES

Table of Contents

ISLABIKES Jimi Adult Mountain Bike
Product Information
Product Usage Instructions
OVERVIEW
Setting up your Islabike
Ready to ride
Usage guidelines
Guarantee
Maintenance
Disc brakes
Wheels
Recommended torque settings
Documents / Resources

ISLABIKES Jimi Adult Mountain Bike

ISLABIKES-Jimi-Adult-Mountain-Bike-product

Product Information

The Jimi bike is manufactured by Islabikes and is designed for safe and enjoyable cycling experiences. It comes with various components, including:

Brake levers
Brake calipers
Rotors
Saddle
Seatpost
Seatpost clamp
Saddle clamp
Stem
Stem bolts
Headset
Headset spacers
Headset adjuster bolt
Handlebars
Grip shift
Rim
Spokes
Tires
Chain
Rear Derailleur
Cassette
Frame
Forks
Cranks

Product Usage Instructions

Step 1 of 6: Remove the front wheel and fork packaging

Remove the packaging protecting the front wheel.
Remove the brake caliper spacer. Note: Do not pull the brake when removing the caliper spacer. Keep the spacer for transportation purposes when the wheel is removed.

Step 2 of 6: Place the front wheel in the fork and install the thru-axle

Place the front wheel into the fork dropouts.
Push the thru-axle through the clearance hole in the right (drive side) leg of the forks and through the wheel hub until the axle reaches the thread in the opposite fork leg.
Hold the thru axle handle and turn it clockwise until
hand-tight.
Check that the front wheel is correctly installed. Lift the front end of the bike off the ground by the handlebars and strike the top of the wheel firmly with the palm of your hand. Push and pull the wheel from side to side. If there is no movement, the wheel is installed correctly. Routinely check that the thru-axle is still tight.

Step 3 of 6: Handlebar setup

Note: This step is only required if mudguards are fitted.

Turn the handlebars clockwise and align them with the front wheel.|
Tighten the two stem clamp bolts with a maximum torque of 7Nm.

Step 4 of 6: Pedal installation (not supplied with the bike)

Important: All pedals are supplied in pairs with a specific left and right pedal. Ensure you have identified the left and right pedals before installation to avoid damaging the crank arm.

Identify the left pedal and tighten it.
Identify the right pedal and tighten it.

Note: Tighten each pedal with a maximum torque of 30Nm.

Step 5 of 6: Adjust saddle height

Loosen the seat post-clamp.
Move the saddle to the desired height.
Tighten clockwise with a maximum torque of 4Nm.

Important: Do not raise the saddle above the minimum insertion mark indicated on the Seatpost.

Step 6 of 6: Brake pad bed-in

Ready to ride! Before you start cycling, ensure your helmet is adjusted correctly according to the manufacturer’s instructions. Wear sturdy footwear and avoid anything getting entangled in the pedals or drivetrain. Familiarize yourself with the bike in a safe environment. Test the brakes to ensure you can come to a stop safely.
For more safety tips, please refer to the advice for safe cycling provided by Islabikes.

OVERVIEW

ISLABIKES-Jimi-Adult-Mountain-Bike-fig-1

Brake levers
Brake calipers
Rotors
Saddle
Seatpost
Seatpost clamp
Saddle clamp
Stem
Stem bolts
Headset
Headset spacers
Headset adjuster bolt
Handlebars
Grip shift
Rim
Spokes
Tyres
Chain
Rear Derailleur
Cassette
Frame
Forks
Cranks

Setting up your Islabike

Step 1 of 6: Remove the front wheel and fork packaging ISLABIKES-Jimi-
Adult-Mountain-Bike-fig-2

Remove front wheel protection packaging.
Remove the brake caliper spacer

DO NOT PULL BRAKE when the caliper spacer is removed. Please keep the caliper spacer for transportation when a wheel is removed.

Step 2 of 6: Place the front wheel in the fork and install the thru-axle

Place the front wheel into the fork dropouts.
Push the thru-axle through the clearance hole in the right (driveside) leg of the forks and through the wheel hub up until the axle reaches the thread in the opposite fork leg.
Hold the thru axle handle and turn clockwise until hand-tight.

Check front wheel is correctly installed. Firstly, lift the front end of the bike off the ground by the handlebars and strike the top of the wheel firmly with the palm of your hand. Secondly, push and pull the wheel from side to side. If there is no movement from either of these actions the wheel is installed correctly.
We strongly recommend routinely checking that the thru axle is still tight.

Step 3 of 6: Handlebar setup

Only required if mudguards are fitted.

Turn handlebars clockwise and align with front wheel
Tighten the two stem clamp bolts Max. 7Nm

Caution: The fork steerer tube is carbon fibre construction, which can be seriously damaged by over tightening.
Failure to correctly tighten stem clamp bolt may result in serious injury or death. If in doubt, please consult our technical support team on +44 (0) 1584 708 383 or email [email protected].
Before riding check front brake operation is correct. To check this, apply both the front and rear brake, they should feel the same. Secondly, push the bike forward whilst holding the front brake to ensure it is working.
Step 4 of 6: Pedal installation (not supplied with bike)

All pedals are supplied in pairs with a specific left and right pedal. This is to prevent the pedals from undoing as you turn the cranks with your feet.
Please ensure that you have identified the left and right pedal before installation to avoid damaging the crank arm.

Left pedal – rotate pedal axle clockwise towards front of bike
Right pedal – rotate axle anti-clockwise towards front of bike Tighten max. 30Nm

Step 5 of 6: Adjust saddle height

Loosen seatpost-clamp
Move to desired height
Tighten clockwise max. 4Nm

Seatposts are clearly marked with minimum insertion mark.
Please do not raise saddle above this line.

Step 6 of 6: Brake pad bed-in

It is important to bed-in your new brake pads to achieve optimal performance, increase pad longevity and reduce the likelihood of brake fade and noise.
To safely achieve optimal results, remain seated on the bike during the entire bed-in procedure. Accelerate the bike to a moderate speed (12mph / 20kph), then firmly apply the brakes until you are at walking speed. Repeat approximately twenty times. Next, accelerate the bike to a faster speed, then firmly apply the brakes until you are at a walking speed. Repeat approximately ten times.
Important: do not lock up the wheels at any point during the bed-in procedure. Allow the brakes to cool prior to any additional riding.
If you require further information about your brakes, contact our technical support team on +44 (0) 1584 708 383 or email [email protected].

Ready to ride

Safety first

Before you head off please read our advice for safe cycling.
Ensure that your helmet is adjusted correctly in accordance with the manufacturer’s instructions.
Ensure you are wearing sturdy footwear and nothing can become entangled in the pedal or drivetrain.
Ensure that you familiarise yourself with your new bicycle in a safe environment. We pride ourselves on light action brakes. Check you can come to a stop safely using the brakes.
Your Islabike is set up so that the right-hand brake lever operates the front brake. Where the destination country drive on the right the right hand brake lever will operate the rear brake.
Be aware braking performance and grip will be drastically reduced in wet conditions.
Ride carefully on busy streets or highways.
Always observe national legal requirements if riding on public roads. If you are cycling in any other countries or in the EU, please check national guidelines.
It is important that your bike is regularly maintained. It should be inspected if an accident occurs.
We do not recommend that a bicycle trailer or trailer bicycle is fitted to this bicycle.
Your bike is fitted with mounting points for a luggage rack, but we do not recommend fitting a child seat.
The moving parts on your bike present a danger of entrapment. Particular care should be taken with the chain when riding and maintaining your bicycle.
Handlebar ends can become exposed from repeated contact with the ground or heavy fall. Never ride a bike with an unplugged handlebar end. You can buy replacement handlebar grips on our website www.islabikes.co.uk or call +44 (0) 1584 708 383.

Usage guidelines

Your Jimi has been designed to be ridden on rough trails, rough unpaved roads and rough terrain that require technical skill. Jumps and drops are intended to be less than 61cm (24 inches).
The maximum safe combined rider and luggage weight limits are as follows:
Jimi S/M/L = 125Kg
Nothing lasts forever, including your bike. When the useful life of your bike or its components are over, continued use is hazardous. Materials and components may react to wear or stress fatigue
in different ways. If the design life of a component has been exceeded it may suddenly fail, possibly causing injuries to the rider. Every bike and its components parts have a finite life. The length of that life will vary with the construction and materials used in the frame and components. Your bike and its components are subject to fatigue. With enough use at high enough loads cracks can develop that could lead to failure. Cracks, scratches or a change of colour could indicate that the design life of the component has been reached and it should be replaced. Extra care should be taken when inspecting parts that are subject to high levels of stress. The science of fatigue is not predictable.

Please note your bike is not intended for the following types of riding:

Dirt jumping
BMX
Four cross
Downhill
Slalom

Factors that can reduce product lifespan include:

Impacts to the bike from crashes, bumps or jumps.
Exceeding the maximum weight limit for the bike.
High mileage/usage.
Environmental conditions (unusually damp/saline atmosphere, muddy or sandy conditions).
Poor maintenance and use out of correct adjustment.
Unsympathetic riding style.

Factors that can increase product lifespan include:

No impacts to the bike from crashes, bumps or jumps.
Observing the maximum weight limit for the bike.
Environmental conditions (dry, clean, non-corrosive environment).
Regular maintenance and careful adjustment.
Sympathetic riding style.
It is not possible to make a bike that is never going to be damaged.
If you use the bike beyond its limitations, there is a high risk of failure which could result in serious injury or death. Bikes that are used competitively should be subject to more frequent and rigorous checks.
Take particular care to check the frame tube junctions and welds as well as all the components for damage or excessive wear.
If in any doubt, please contact our technical support team on +44 (0) 1584 708 383 or email [email protected]. Or take it to a qualified cycle mechanic for inspection.

Guarantee

Your Islabike comes with a 5-year guarantee on frame and forks and a 2-year guarantee on parts. This covers faulty manufacturing but not normal wear and tear. This guarantee only applies to the original purchaser of the bike.
Your statutory rights are not affected by the guarantee.
Our clearance bikes have the following guarantees, these apply to the original purchaser and are only valid within the UK.
Ex-display / Demo: 5-years frame and forks / 2-years parts Second hand: 12-months frame and forks
Our bikes are not guaranteed for racing in sanctioned or competitiveevents. The use of a bicycle in hazardous conditions including changeable and uneven surfaces can put high, unpredictable loads on the bicycle and its components. Lack of rider skill and experience can further increase these loads leading to the possibility of serious damage to the bicycle and/or injury to the rider. If you choose to participate in these events then please carry out more frequent and thorough maintenance and checks, including regularly inspecting the frame, fork, stem, cranks and handlebars for signs of damage.
Discontinue use immediately if anything untoward is spotted and contact our technical support team on +44 (0) 1584 708 383 or email [email protected].

Maintenance

Keeping your bike clean and maintained comes with many benefits.
Not only will your Islabike perform better but it will be safer, last longer and look great. To do this we have listed some regular checks to help you along the way. Of course, if you are unsure of anything we strongly recommend you seek professional advice or contact our technical support team on +44 (0) 1584 708 383 or email [email protected].
Firstly, moving parts on your bicycle will need lubricating from time to time. Weather conditions are generally the biggest factor that determine frequency of maintenance and lubrication. However, it is also heavily dependent on the frequency, type and duration of riding.

Component

Chain

| Lubricant

Oil

| Frequency

Weekly or after washing / rain

---|---|---
Gear cables| Oil| Monthly or after washing / rain
Wheel bearings| Grease| 6 months
Headset| n/a| Sealed bearings
Brake fluid| Mineral oil| 12 months – service
Bottom bracket| n/a| Sealed bearings

Disc brakes

One of the most important safety features of your Islabike. It is a good habit to check the brakes on a regular basis. This should be done depending on the type, frequency or duration of riding. If your bike has not been used for a period of time, we recommend a quick check before riding.
Brake operation – Pull on one brake at a time and look at the brake pads. Check to see if they are touching the discs evenly when applied. If the pads are not contacting the discs correctly, they are uneven, rubbing or feel spongy to apply please contact our technical support team on +44 (0) 1584 708 383 or email [email protected].
Brake pad wear and replacement – Brake pads do not last forever. Eventually they will need replacing. This will depend on the type, frequency and duration of riding. Brake pads must be replaced if the total thickness of the backing plate and pad friction material is less than 3mm.
Riding with backing plate and pad friction material less than 3mm can result in reduced braking performance, crash, and/or death.
Pads fitted as standard are organic compound. We recommend replacing with the same compound to maintain performance.
Brake fluid and replacement – The brakes fitted to your bike contain Mineral oil. Your fluid will need replacing annually to maintain performance. Always seek professional advice – specialist tools are required for this maintenance.
DO NOT ALLOW brake fluid to contact skin or eyes. If fluid comes into contact with skin or eyes seek to dilute with plenty water and seek medical advice.

Wheels

Rim trueness – Depending on the type of riding you do your Islabikes bikes wheels may become untrue or damaged when riding. This means they will not spin straight and will wobble. If for any reason they are untrue our wheels can be easily repaired, please contact our technical support team on +44 (0) 1584 708 383 or email [email protected].
Hubs – Your hubs are fitted with sealed cartridge bearings. These cartridge bearings are not adjustable or serviceable and should be replaced when they become worn.

Tyres and Tubes

Tyre wear – Regularly check tyres for general wear and tear. Overtime your tyres will become more worn and can become more susceptible
to punctures.
Tyre pressure – Regularly check your Islabike tyre pressure as they slowly go down over time. To check, simply push your thumb hard onto the tyre or use a pressure gauge fitted to most quality bicycle track pumps. If you can touch the rim this probably needs some more air.
You should not exceed the maximum tyre pressure printed on the sidewall of the tyre. We recommend approx. 70% of the maximum tyre pressure illustrated on your tyre. To inflate presta valves you must first open the valve by unscrewing and tapping the valve end to relieve it if stuck. Inflate to correct pressure and then carefully re-tighten to close the valve.
Use our guide to inflate your tyres, https://www.islabikes.co.uk/knowledge/technical-support/maintaining-your-islabike/

Drivetrain

The drivetrain is a category of components made up of the chain, cranks, cassette and pedals. These components work together to drive your Islabike forward and are crucial in maintaining the optimum performance and life of your Islabike. To keep these running smoothly we advise the following.
Chain cleaning and lubricating – We recommend cleaning & lubricating your chain weekly or after washing/rain. Simply use soapy water to wipe over your chain and rear derailleur then dry with a cloth. Then gently apply any general bicycle oil direct whilst simultaneously turning the cranks backwards to ensure full chain coverage. Wipe off any surplus oil with a cloth.

Gears

Your Islabike has had its gears adjusted prior to delivery. These should be checked periodically or after a fall to ensure they are operating correctly. Quick check:
Ensure your rear derailleur hanger is not twisted or bent.
Place your Islabike in gear 1 or the biggest sprocket and look from the rear. Look out to see if the rear derailleur is fouling the spokes or looks twisted.
If the gears are not working correctly contact our technical support team on +44 (0) 1584 708 383 or email [email protected].

Recommended torque settings

All stem bolts 7Nm
Saddle clamp bolts 7Nm
Seatpost collar bolt 4Nm
Crank bolts 35Nm
Pedals 30Nm
Caliper bolts 9Nm
Rotor bolts 6Nm
Rear derailleur 6Nm

Spares and replacement parts

We carry stock of replacement parts for your Islabike including inner tubes, tyres and grips. Please visit our website for a list of readily available spares.
We only recommend using genuine parts for safety critical components e.g. brake cables, brake blocks and bolts.
If you can’t find what you are looking for or are unsure of any compatibility for older models, please contact our technical support team by phone or email. [email protected] +44 (0) 1584 708 383
For technical support and cycling advise please see the knowledge area of our website. www.islabikes.co.uk/knowledge/

Frame number

Please make a record of your frame number. This is a combination of letters and numbers unique to your bike stamped to the underside of the frame. This is required by police and insurance companies in case of loss

www.islabikes.co.uk