GAINSBOROUGH 8955 BB Series Omni Trilock Twin Pull Handle Instruction Manual

Table of Contents

GAINSBOROUGH 8955 BB Series Omni Trilock Twin Pull Handle

GAINSBOROUGH 8955 BB Series Omni Trilock Twin Pull
Handle

Step 1.

Fold template where indicated.
Position template on door edge at desired lock / latch height.
Firmly hold template and mark latch height and 2 off 60mm holes centres.
Measure door thickness and mark centre on ‘latch height’ marking.
Drill 22mm (7/8″) latch hole.
Note: it is important to drill this hole squarely.
Drill pilot holes [suggested size 3mm (1/8″)]. Then enlarge holes to 60mm, drilling from both sides of the door.
In particular, ensure the 60mm dia. holes through door face are drilled only to this size, otherwise correct functioning may be impeded – refer template.

Step 2.

Step 3.

Mark and chisel latch faceplate to a recess of 2.5mm.
Use latch carrier as a template.
Insert lock body into 60mm (2 3/8″) slot.
Insert latch carrier through 22mm (7/8″) hole into lock body assembly and tighten with 2 screws.
Ensure T-shaped hole at rear of latch carrier is upright!

Step 4.

Step 4a

Trilock Latch Bolt re-handing.

NOTE:

carefully follow these instructions when installing.
do not overtighten screws.
use of power driver is not recommended.
fully remove the Trilock prior to painting the door to avoid harming the product’s finish.

Step 5

Remove perforated cut-out from card-board template and place over lock body, making sure template is square to door edge.
While holding template firmly in position, mark remaining 3 holes, as indicated on both sides of the door (reversing template as required).
Drill pilot holes from both sides of the door [suggested size 3mm (1/8″)] then enlarge, again from both sides of the door, to sizes indicated on template, otherwise correct functioning may be impeded – refer template.

Step 6

To rehand external lever & set lever operation (if required).

If rehanding is required remove the stop screw from SS1 & fit to SS2, to allow Lever to operate away from door edge

Step 7

Install 2 posts to Trilock external faceplate (this is the faceplate without the rectangular snib push-button).

Step 8

Mount the Inside face plate so that mark on large gear engages with mark on lock bodygear

Step 9

Insert spring and snib rotor in the square hole of the internal lever.
Position snib rotor so one notch faces up and the other notch points to the latch side.
Mount outside furniture plate to outside of the door, and align the two making sure the snib rotor engages with the external lever.
Fit mounting screws from inside and tighten into threaded posts.
Fit wood screws 3 off to inside furniture plate (recommend pilot drilling before fitting screws).

NOTE : Test all functions for smooth operation.

NOTE:

carefully follow these instructions when installing.
do not overtighten screws.
use of power driver is not recommended.
fully remove the Trilock prior to painting the door to avoid harming the product’s finish.

Step 10

For single cylinder applications install internal turnbutton now by tightening grub-screw onto protruding shaft.

Step 11

All door seals must be fitted prior to fitting strike plate.

Position the door so that the CenterPoint of the strike plate can be marked on door frame.
Mark and drill a 25mm (1″) hole to a depth of 25mm (1″), at a corresponding height to the bolt.
Mark and chisel recesses for strike plate and optional reinforced strike plate.
Screw into position using 4 wood screws as supplied.
Note: 2 larger screws should be used on reinforced strike plate as illustrated.

Door Adjustment

When door is closed using finger pressure, ensure bolt is latching into strike plate.
If door is rattling when in latched position. Open door, remove strike plate & adjust anti-rattle tab & refit strike plate to door frame. Repeat check 1.

Step 13
Fixing of double pull handle

Note: Suitable for solid doors only

Check and make sure that the inside & outside faceplates are lined up straight and square with the door.
Once the desired position of the inside & outside faceplate has been confirmed, mark the centre of the hole at the top of the faceplate and proceed to drill a suitable hole. Note: When drilling the hole drill hole from both sides of the door with a 9mm drill bit.
On the inside faceplate, hold the optional rectangular plastic washer centred over the hole against the door surface.
Then hold the unthreaded bush onto the outside faceplate, ensuring the larger section of the bush, as marked ‘A’ in illustration, is facing the door.
Then, from the same side, install the suitable M8 screw through the bush and optional plastic washer (if used) and through the door.
Then, from the outside faceplate fit the threaded bush
Tighten M8 screw securely with suitable screwdriver.
Place the pull handle over top of 2 mounting bushes.
Line up the pull handle so that it is lined up straight and square. Insert the grub screws and tighten with allen key provided

NOTE:

carefully follow these instructions when installing.
do not overtighten screws.
use of power driver is not recommended.
fully remove the Trilock prior to painting the door to avoid harming the product’s finish.