hansgrohe AXOR Montreux, Carlton, Terrano, Citterio Mixers Instruction Manual
- June 12, 2024
- hansgrohe
Table of Contents
Montreux, Carlton, Terrano, Citterio Mixers
Instruction Manual
Montreux, Carlton, Terrano, Citterio Mixers
****
**** Safety Notes
Gloves should be worn during installation to prevent crushing and
cutting injuries.
The shower system may only be used for bathing, hygienic and body
cleansing purposes.
Children as well as adults with physical, mental and/ or sensoric
impairments must not use this shower system without proper supervision.
Persons under the influence of alcohol or drugs are prohibited from using this
shower system.
The hot and cold supplies must be of equal pressures.
Installation Instructions
The fitting must be installed, flushed and tested after the valid norms!
Thermostatic mixer in conjunction with combination boilers
- If fitting a hand shower remove the water limiter from the shower.
- If the continuous water heater causes any problems, or you have different water pressures you must install a water limiter to the cold supply, (ordered separately,article number 97510000).
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 – 0,5MPa
Test pressure: 1,6MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 80°C
Recommended hot water temp.: 65°C anti-pollution function
Symbol description
Do not use silicone containing acetic acid!
Safety Function (see page 62)
The desired maximum temperature for example max. 42° C can be pre-set thanks
to the safety function.
Adjustment (see page 63)
After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured or the output
differs from the temperature set on the thermostat.
Maintenance (see page 68)
To guarantee the smooth running of the thermostat, it is necessary from time
to time to turn the thermostat from total hot to total cold.
The mixer is equipped with non return valves. The non return valves must be
checked regularly according to DIN EN 1717 in occordonce with notional or
regional regulations lot least once o year/.
Operation (see page 64)
Dimensions (see page 66)
Flow diagram (see page 67) 0 Shower (D Both tub
Spare parts (see page 69)
Test certificate (see page 67)
| Fault | Cause | Remedy |
|---|---|---|
| Insufficient water | – Supply pressure inadequate | – Check water pressure (If a |
pump has been installed check to see if the pump is working).
– Filters are dirty (96922000)| – Clean filter in front of the mixer and on
the MTC-thermo cartridge (96922000)
– Shower filter seal dirty| – Clean filter seal between shower and hose
Crossflow, hot water being forced into cold water pipe, or vice versa, when
mixer is closed| – Backflow preventers dirty or leaking| – Clean backflow
preventers, exchange if necessary
Spout temperature does not correspond with temperature set| – Thermostat has
not been adjusted| – Adjust thermostat
– Hot water temperature too low| – Increase hot water temperature to 42 °C to
65 °C
Temperature regulation not possible| – thermo cartridge calcified| – Exchange
thermo cartridge
Shower or spout dripping| – Dirt or sedimentation on valve seat, shut-off unit
damaged| – Clean or exchange shut-off unit
Instantaneous heater didn’t work with thermostat| – Flow limiter in handshower
isn’t removed| – Remove flow limiter
– Filters are dirty| – Clean the filter / exchange filter
– Non return valve hasn’t moved back| – Exchange non return valves
Assembly see page 60
Hansgrohe · Postfach 1145
D-77761 Schiltach
Telefon +49 (0) 78 36/51-1282
Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com
Internet: www.hansgrohe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>