BEEPRT C10 Series Thermal Label Printer User Manual

Thermal Label Printer
Applicable models: C10 Series
User Manual
Version: 1.0

C10 Series Thermal Label Printer

Thanks for choosing us!
If you have any question or concern, support is available by email . Problems could be resolved quickly.
  Support@beeprt.net
Please visit the website “help.ayinprinter.com” to download the printer driver and see the installation tutorial
Support Web: help.ayinprinter.com

https://help.ayinprinter.com/support/solutions/folders/73000564180

![BEEPRT C10 Series Thermal Label Printer - Fig](https://manuals.plus/wp-content/uploads/2023/06/BEEPRT-C10-Series-Thermal-Label-Printer-Fig.png)

Appearance

Packing list

Note: If any accessories missing, please contact us to get support.

Printer Connection

Note:

• Make sure the printer is off before connecting the power cord to printer.
• Use the original power adapter only in case the damage caused by charging improperly.
• Please unplug the printer power cord if it is not in use for a long time.

The suitable label size

• Shipping label printer works with any Thermal Direct with a width range from 1.57″ to 4.1″, length over 0.8″. Normal paper is not applicable! Must be THERMAL LABEL!
• Ideal for 4°*6”
• Paper size can be selected in Windows and MacBook both.

Label standard size

How to feed label

Ensure the printer is off| Pull the release latch to open the cover

Insert the roll label, adjust the paper guide to fit the width of paper.

Note: Ensure the print layer of label face up in case print out blank labels.

Close the cover, switch on the printer and wait 5 seconds for the printer to initialize.
Long press the feed button until you hear one beep, release your finger, the label calibrates automatically and will be positioned at the tear-off point, then ready to print.

Note:

• Each time you change the label, please follow the above steps 5.1~5.4.Otherwise, it may cause printing out misaligned or blank.
• Every time you open the label cover even you never change the paper, you’d better to press the feed button once to load one sheet paper.

Installation For Printer Driver

6.1 Install Beeprt Driver on Windows

https://help.ayinprinter.com/support/solutions/articles/73000605924 -install-beeprt-driver-on-windows

Scan the code to watch the windows driver installation video.
6.2 Installation For Windows via Sluetooth

https://help.ayinprinter.com/support/solutions/articles/73000605719 -how-to-print-on-windows-via-bluetooth-

Scan the code to watch the windows bluetooth installation video.
6.3 Installation For MacOS via USB Port

[ https://help.ayinprinter.com/support/solutions/articles/73000605718 -install-beeprt-printer-driver-on- mac](https://help.ayinprinter.com/support/solutions/articles/73000605718 -install-beeprt-printer-driver-on-mac)

Scan the code to watch the McOS Driver installation video.
6.4 Installation For Chromebook via USB Port

****https://help.ayinprinter.com/support/solutions/articles/73000605720-how- to-print-on-chromebook-

Scan the code to watch the Chromebook Driver installation video.

Smartphone APP Setup

Please search for “Shipping Printer Pro” in your APP store and install it.

https://help.ayinprinter.com/support/solutions/articles/73000605721 -how-to-install-app-on-phone-

Scan the code to watch the video of APP usage.

FAQs

https://help.ayinprinter.com/support/solutions/folders/73000408514

Maintanance

CLEANING THE PRINT HEAD
The printer head is a sensitive part of the printer and can be found on the upper part of the printer when open.
Caution: While the printer is running the printer head can be very hot.

1. Ensure that the power switch is OFF ,remove the power cord, and open the cover . wait several moments to ensure that the printerhead cools down.
2. Completely clean the printer head using an alcohol swab like the one provided. Any 70% Isopropyl! Alcohol pad would work . Please do not use water.
3. Wait 2-3minutes until the alcohol has completely dried, then close the cover.
4. Connect the power cord and print a test page to check if it is clean.

Pro tips

– Anytime you’d like to change your label size, run the automatic label identification by pressing and holding the feeder button until you hear one short beep.
– Press the green feeder button on the printer to skip a blank label.
– Torun a self-test, press and hold the feeder button until you hear two short beeps.
– Avoid using poor quality labels as they can damage the printer.
– Regularly clean the printer head as outined above, under MAINTENANCE.
– If paper is jammed, turn off the printer, and allow the printer head to cool down. Open the cover and ensure that the rubber is clean. If it is dirty, use alcohol pad to clean it. Allow the area to dry before turning the printer back on.
– Insert the printer’s USB into the USB port on your computer every time you plug it in. This will avoid creating duplicate copies of the printer on your computer.

LED indicator

the printer heed cocia down.
Flashing Red (every 2 seconds)| 1.0ut of paper
2.Wrong size paper| Eosin that Vie labels are loaded compedy. You may need la run
llillOrnatle label identration (point 6 In Nape).
Flashing Red (2 times per second)| Printer cover is not fully closed| Check that the printer cover is completely closed.

Safety tips

– The printer head can become very hot after printing labels .Do not touch the printer head until it has cooled.
– Do not bend the power cord excessively or place objects on the cord. This could result in fire or electocution.
– Keep the printer out of reach of children.
– Use only approved accessories and do not try to disassemble or repair the unit by yourself.
– Keep the printer away from water and other objects that may destroy or damage the device.
– Printer should remain unplugged when not in use for long periods of time.

IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Canadian ICES-003 and RSS-210 & RSS-247.
Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
IC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located for operating in conjunction with any other antenna or transmitter.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions:

1. this device may not cause harmful interference, and
2. this device must acceptany interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

BEEPRT SUPPORT
Still have a question or concern?
Most issues can be resolved very quickly!
Customer service support is available by
Please kindly contact us
Index: www.beeprt.net
Driver: help.ayinprinter.com WhatsApp
E-mail: support@beeprt.net https://wa.me/qr/XSYVGM2KBG2GE1
Whatsapp
After-sales service

References

• Support : Ayin-QiRui-BEEPRT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>