hansgrohe 72405000 Talis S Bath Mixers Instruction Manual
- June 12, 2024
- hansgrohe
Table of Contents
- hansgrohe 72405000 Talis S Bath Mixers
- Product Information
- Product Usage Instructions
- Safety Notes
- Installation Instructions
- Technical Data
- Symbol description
- Troubleshooting
- Assembly Instruction
- Cleaning recommendation / Warranty / Contact
- Dimension
- Flow diagram
- Operation
- Spare Parts
- Special accessory
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe 72405000 Talis S Bath Mixers
Product Information
The product is a plumbing fixture that is used for bathing, hygienic and body cleaning purposes. It is designed for drinking water and has a maximum operating pressure of 1 MPa. The recommended operating pressure is between 0.1 and 0.5 MPa. The product has a test pressure of 1.6 MPa and a hot water temperature that can be adjusted by the user.
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The hot and cold supplies must be of equal pressures.
- Do not use silicone containing acetic acid!
Technical Data
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0.1 – 0.5 MPa
- Test pressure: 1.6 MPa
- Hot water temperature: adjustable
Product Usage Instructions
- Make sure the hot and cold water supplies are of equal pressures.
- Adjust the hot water temperature as desired.
- During installation, wear gloves to prevent crushing and cutting injuries.
- Do not use silicone containing acetic acid!
Maintenance
- For cleaning instructions, refer to page 37 of the user manual.
- To adjust the product, refer to page 36 of the user manual.
- To troubleshoot common issues, refer to page 39 of the user manual.
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The product may only be used for bathing, hygienic and body cleaning purposes.
- The hot and cold supplies must be of equal pressures.
Installation Instructions
- Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
- The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
- The plumbing codes applicable in the respective countries must be observed.
Technical Data
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0,1 – 0,5 MPa
- Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature: max. 60°C
- Thermal disinfection: 70°C / 4 min
The product is exclusively designed for drinking water!
Symbol description
-
Do not use silicone containing acetic acid!
-
Adjustment
To adjust the hot water limiter. Using a hot water limiter in combination with a continuous flow water heater is not recommended. -
Dimensions
-
Flow diagram
free flow -
Spare parts
XXX = Colors
000 = Chrome Plated
090 = Chrome Plated/Gold Plated
130 = Polished Bronze
140 = Brushed Bronze
250 = Brushed Gold-Optic
330 = Polished Black Chrome
340 = Brushed Black Chrome
400 = White/Chrome Plated
670 = Matt Black
700 = Matt White
820 = Brushed Nickel
950 = Brushed Brass
990 = Polished Gold-Optic
Special accessories (see page 40)
order as an extra- extension 25 mm #13595000
- Extension Set 22 mm (when wall is not deep enough) #15597XXX, #13597XXX, #13593XXX
-
Cleaning
-
Operation
-
Test certificate
Troubleshooting
Assembly Instruction
Cleaning recommendation / Warranty / Contact
www.hansgrohe.com/cleaning-recommendation
www.hansgrohe.com/cleaning-recommendation
www.hansgrohe.com/cleaning-recommendation
www.hansgrohe.com/cleaning-recommendation
Dimension
Flow diagram
Operation
Spare Parts
Special accessory
Hansgrohe · Postfach 1145 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282
· Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet:
www.hansgrohe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>