hansgrohe Zesis M33 150 1jet 74802XXX Single Lever Kitchen Mixer Instruction Manual
- June 12, 2024
- hansgrohe
Table of Contents
- hansgrohe Zesis M33 150 1jet 74802XXX Single Lever Kitchen Mixer
- Product Information
- Product Usage Instructions
- Safety instructions
- Installation instructions
- Specifications
- Description of symbols
- Size
- Accessories
- Other accessories
- Adapter
- Cleaning
- Use
- Assembly
- OPERATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe Zesis M33 150 1jet 74802XXX Single Lever Kitchen Mixer
Product Information
- Product Name : Zesis
- Model Numbers : M33 150 1jet 74802XXX, M33 150 Eco 1jet 74811000, M33 150 CoolStart EcoSmart 1jet 74813000, M33 200 CoolStart 1jet 74807000, M33 200 1jet 74808000, M34 150 1jet 74815XXX, M33 160 1jet 74805000
- Manufacturer : Hansgrohe
- Recommended water pressure : 0.1 – 0.5 MPa
- Maximum water pressure : 1 MPa
- Control pressure : 1.6 MPa (1 MPa = 10 bar = 147 PSI)
- Colors available : Matt Black (670), Stainless Steel Optic (800), and Chrome (000)
Product Usage Instructions
To use the Zesis product:
- Ensure that the recommended water pressure is between 0.1 – 0.5 MPa.
- Turn on the water supply.
- Adjust the temperature using the temperature control.
- Use the lever to control the water flow.
- To clean the product, refer to page 48 of the user manual.
If you experience any issues with the product:
- If there is insufficient water flow, replace the cartridge or O-ring.
- If the battery life is low, replace the battery.
- If the water temperature is too high, adjust the temperature limiter.
For installation instructions, refer to page 34 of the user manual.
MODELS
Safety instructions
- Bruises and cuts during installation gloves must be worn to avoid
- Between the cold water and hot water connections a large pressure difference must be compensated!
Installation instructions
- Before installation, it must be checked that the product does it have any shipping damage. After installation, the delivery or surface damage is not recognized.
- The wires and the faucet are valid must be installed and flushed in accordance with standards and check
- Installation instructions valid in each country guidelines must be followed.
- 74811000 : The water tap must not flow through use with a water heater.
- 74807000, 74808000 : Only with the DVGW mark equipped dishwashers or washing machines are not allowed without additional insurance for the connection valve of the device connect. If not connected user to the connection valve of the device, then this must be plugged in
Specifications
- Operating pressure : max. 1 MPa
- Recommended operating pressure: 0.1 – 0.5 MPa
- Pressure test : 1.6 MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature : max. 60°C
- Thermal disinfection : 70°C / 4 minutes
The product is designed for drinking water only!
Description of symbols
- Do not use silicone containing acetic acid!
- Setting (see page 37)
Setting the hot water limitation. Restrictive use of hot water is not recommended for flow-through water heaters
Size
Flow chart
Accessories
- XXX = Color coding
- 000 = Chrome
- 670 = Matt Black
- 800 = Stainless Steel Optic
Other accessories
(not included in the delivery unit)
Adapter
(G⅜ / G½) #93395000
Cleaning
www.hansgrohe.com/cleaning-recommendation
Use
- The temperature of the water flowing through the taps for consumption in the case of intended water, it cannot exceed 65°C yes. The faucet cannot result in the human water intended for consumption (e.g. for drinking and cooking). quality deterioration.
- It must be strictly closed after start-up and shutdowns follow the instructions in the user manual. During commissioning the faucet must be flushed, at least 2 minutes of cold and hot water we recommend. After a minimum of 1 day of downtime stagnant cold in the faucet before consumption drinking hot water from the tap is not recommended stagnant water must be released for at least 2 minutes continuation is recommended. It gained water during the discharge do not use it as drinking water or for food preparation free.
- Considering the ability of hot water to dissolve metals higher than cold water, therefore cooking for drinking OKI recommends using cold water.
- It is recommended to descale the aerator of the faucets every month, or to disinfect. Cleaning the faucets, only such chemicals during disinfection applicable, which complies with 201/2001. (X.25) Government Decree and 38/2003. (VII.7) as described in the joint decree of the ÉSzCsM-FVM-KvVM.
- Due to the operating principle of the aerator, it is significant forms an aerosol, thus from the point of view of Legionella exposure poses an increased risk. Hence its application not recommended for healthcare facilities in inpatient care rooms, or anything like that place where the cold and / or domestic hot water Legionella germ count reaches 49/2015 (XI.6.) intervention determined on the basis of EMMI regulation level.
Hungarian
Fault
- Little water
- The faucet is difficult to open.
- The sap is dripping.
- Water outlet is the tiltable spout area
- Stepping out on the retaining bar hot water temperature too low
OK
- The aerator is calcified, contaminated
- The ceramic insert has failed, calcified.
- The ceramic insert has failed
- Lord Témítogyrú has broken down
- Connecting hose sealing ring failed
- The hot water regulator is bad is set.
Solution
- Clean the aerator / to exchange.
- The ceramic insert must be replaced.
- The ceramic insert must be replaced.
- Replacement of TömitogyUrü
- Replacement of the sealing ring
- Turn the hot water regulator back on must be stated.
Assembly
OPERATION
Zesis M33 150 1jet 74802XXX
- open
- close
- hot
- cold
Zesis M33 200 1jet 74808000
- open
- close
Zesis M33 150 CoolStart EcoSmart 1jet 74813000
- open
- close
- hot
- cold
Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach
- Telefon +49 (0) 78 36/51-1282
- Telefax +49 (0) 7836/511440
- E-Mail : info@hansgrohe.com
- Internet : www.hansgrohe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>