RUN BISON LJC-UFO-32-277-8240C-30ED 4PK Integrated UFO LED High Bay Light Fixture Instruction Manual
- October 30, 2023
- RUN BISON
Table of Contents
RUN BISON LJC-UFO-32-277-8240C-30ED 4PK Integrated UFO LED High Bay Light
Fixture
CCT & Wattage Selectable Integrated LED UFO High Bay Light Fixture
Our UFO high bay light is a cost-efficient solution and a great replacement
for your metal productivity, halides, and electricity. HID bill, or improCFL
ve Bulbs. visibility, reading help to you LED work can safe save ly, yours and
money enhance
Before returning to your retailer, please contact support@runbisonlighting.com if you have any questions or problems with this product
Safety Instruction
WARNING
- To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
- Commercial installation, service, and maintenance of luminaires should be performed by a qualified licensed electrician.
- For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
WARNING
- Tum off electrical power at the fuse or circuit breaker box before wiring the fixture to the power supply.
- Tum off the power when you perform any maintenance.
- Verify that the supply voltage is correct by comparing it with the luminaire label information.
- All wiring connections should be capped with UL-approved wire connectors
CAUTION
- • Avoid direct eye exposure to the light source while it is on.
- • Account for small parts and destroy packing material, as these may be hazardous to children.
- • Risk of bum. Disconnect power and allow the fixture to cool before changing the bulb or handling the fixture.
NOTICE: Green ground screw provided in the proper location. Do not
relocate.
NOTICE: Minimum 90′ supply conductors.
NOTICE: Specifications and dimensions are subject to change without
notice.
NOTICE: Suitable for Dry or Damp locations.
Tools Required
Optional fittings
Electrical Schematic Diagram
Without any function,0-10V Dimming wiring diagram
Installation Guide
Hooking Mounting
- Connect the black wire(Live Wire), white (Neutral wire), and green wire (Ground) to the appropriate wire inside the junction box.
- To make the lamp dimmable, please connect the 0-10V dimmer( not include} with the dimming signal of the lamp, and connect the DIM+ port and DIM- port with the corresponding line on the dimmer.
Ceiling-Mounted Installation (Using optional U Mount Bracket
- To install the optional U bracket on the luminaire, begin by attaching the L-shaped U mounting brackets on the luminaire. (See Figure 2)
- Next, attach the U bracket to the L-shaped U mounting brackets (see Figure 3)
- Using the U-mount bracket as a template, mark and drill holes in the ceiling or other solid structure to which the luminaire will be attached. (See Figure 4)
- Use a hammer to install the expansion screws into the drilled holes. (See Figure 5)
- Using the enclosed nut, install the U mounting bracket onto the expansion screws, and securely tighten the nuts. (See Figure 6 )
- If the luminaire will be installed at an angle (See step 7), tighten the mounting bracket adjustment bolts only partially tight. Otherwise, securely tighten these bolts.
- If the luminaire will be installed at an angle, rotate the luminaire up to 50°in either direction (100°total adjustability), and securely tighten the mounting bracket adjustment bolts.
- Refer to the Wiring Diagram to make electrical connections.
SURFACE MOUNT BRACKET INSTALLATION
- Ceiling
- Wall
PENDANT MOUNT BRACKET INSTALLATION
Sold separately
- Remove the original ring from the driver.
- Install the adapter and secure it to the driver using an M10 or M12 screw (included with the adapter).
- Screw the adapter with the fixture onto a Pendant and secure it with an M3 screw (included with the adapter).
DIFFUSER AND LENS INSTALLATION
Sold separately
- Install the diffuser, and tighten the screws.
- Attach the conical lens to the included clamp.
The lamp has 3 selectable CCTs and 3 wattages
- Open the silicone cover of the CCT or power DIP switch respectively.
- Toggle the DIP switch to the corresponding gear as indicated by the laser engraving arrow to achieve the required CCT and power conversion.
NOTED
LJC-UFO-26/277-8150C-30ED Factory Setting: 150W,5000K
LJC-UFO-32/277-8240C-30ED Factory Setting: 240W,5000K
WARRANTY
This product is warranted for 5 years from the date of purchase. If this
product does not perform to the specifications supplied on this package, send
an email to support@runbisonlighting.com for product return and replacement.
This replacement is the sole remedy available. Liability for incidental or
consequential damage is expressly excluded.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>