XPRIT Beach Seal Electric Bike Instruction Manual

XPRIT Beach Seal Electric Bike

Product Information

Beach Seal E-bike
The Beach Seal E-bike is an electric bike that requires assembly before use. Please follow the instructions below to set up your bike.

Instructions to Set Up Your Beach Seal E-bike

1. Re-seat and charge the battery before the first ride.
2. Make sure the pedals are tight.
3. Make sure the front wheel is installed properly and tight.
4. Inflate the tires properly.
5. Check that all screws are properly torqued.
6. Carry out a fine adjustment of the gears and brakes.
7. Learn how to use the LCD display.
8. Wear a helmet before riding.

Please Note:
Your bike may need further adjustments after assembly. If you have any trouble with setup, please contact us online or through our email address: support@xprit.com.

Product Usage Instruction

Assembling Your E-Bike

1. Read all of the instructions carefully. Be familiar with the proper operation of all items.
2. This quick guide is intended to list the steps needed to assemble your bike with some.

Installing Your Handlebars

1. Place the handlebar in the handlebar mount being careful with the wires.
2. Face the mounting brackets on the front end of the mount with the round edges facing outward.
3. Adjust the handlebar angle to your comfortable riding posture.
4. Secure the mounting brackets with four screws. (Screws shall be tightened with 6N.m torque)
5. Verify your front tire lines up with your headset.
6. Check whether all headset items are tight.

Installing Your Front Wheel – Through Axle Version

1. Insert the axle into the wheel hub as shown. Add the Slim Spacer on the LEFT side (Brake Disk) and the Wide Spacer on the RIGHT side.
2. Insert the front wheel with the spacers in between the front fork on the bike. Be sure to align the disk between the brake caliper as shown in Figure 2.
3. Now on the outside add the washer and nut on each side and hand turn until snug.
4. Using your wrench, tighten each side alternatively until snug (you might need to secure the opposite nut slightly so the whole axle doesn’t turn).
5. Now tighten each nut putting your weight into the wrench. Your front wheel is now installed.
6. The Adjustment Nut needs to be very tight, be sure to retighten after your first couple rides.

Installing Your Front Fender

1. Align the fender clamps on the left and right legs of the fork with fender stay to enable fender in the line with the wheel. Fix the stay with screws (M5 screw) provided on the clamp.
2. Put the lifting lug of the fender behind fork gantry installing hole. Link and secure these two pieces with the fixing screw (M6 screw) and washer.

Installing Your Pedals

1. Warning: Incorrect installation will cause damage. Please read the instructions and watch our videos if needed.
2. Identify the Left and Right markings on the pedals. They can only be installed in their respective side.
   • L is for the Left Pedal and it goes on the Left Crank Arm.
   • R is for the Right pedal and it goes on the Right Crank Arm (Chain Side).
3. Sitting on your bike the pedals go on the Left and Right side respectively.
4. Keep the pedal Horizontal while hand screwing to get the thread started. Then Use your 15mm wrench to tighten them.
5. Both pedals tighten towards the front of the bike. The left pedal is reverse threaded to allow.

Diagram

We know you are excited about getting going but please:

• Reseat and charge the battery before the first ride
• Make sure the pedals are tight
• Make sure the front wheel is installed properly and tight
• Inflate the tires properly
• Check that all screws are properly torqued
• Carry out a fine adjustment of the gears and brakes
• Learn how to use the LCD display
• Wear a helmet before riding

Please Note: Your bike may need further adjustments after assembly.

If you have any trouble with setup, please contact us online or through our email address: support@xprit.com.

Assembling Your E-Bike

1. Read all of the instructions carefully. Be familiar with the proper operation of all items.
2. This quick guide is intended to list the steps needed to assemble your bike with some mechanical skills. It is not a complete manual or training. If you do not feel comfortable or lack some of the skills to assemble it yourself, reach out to a cyclist friend, a local bike mechanic or one of our support technicians for guidance.
3. Our QA mechanics have assembled and tested your bike beforehand.
4. To assemble your bike, work on a clean area with enough space to maneuver.
5. If installed, remove the battery from the bike to start the assembly。
6. Inspect the bike completely to be sure no damage occurred during shipping.
7. The kickstand is designed to support the bicycle only. Not the rider mounted。
8. You can adjust your saddle position and the tilt on your handlebar items for comfort.
9. Check all screws and parts are tight and properly fixed. We recommend a pre-trip inspection before your first rides.
10. Before riding, make sure battery is properly assembled and tightly locked on the bike in case of any dropping.

Installing Your Handlebars

1. Place the handlebar in the handlebar mount being careful with the wires.
2. Face the mounting brackets on the front end of the mount with the round edges facing outward. Adjust the handlebar angle to your comfortable riding posture.
3. Secure the mounting brackets with four screws. (Screws shall be tightened with 6N.m torque)
4. Verify your front tire lines up with your headset.
5. Check whether all headset items are tight.

Installing Your Front Wheel – Through Axle Version

1. Insert the axle into the wheel hub as shown. Add the Slim Spacer on the LEFT side (Brake Disk) and the Wide Spacer on the RIGHT side.
2. Insert the front wheel with the spacers in between the front fork on the bike. Be sure to align the disk between the brake caliper as shown in Figure 2.
3. Now on the outside add the washer and nut on each side and hand turn until snug
4. Using your wrench, tighten each side alternatively until snug (you might need to secure the opposite nut slightly so the whole axle doesn’t turn)
5. Now tighten each nut putting your weight into the wrench. Your front wheel is now installed.
6. The Adjustment Nut needs to be very tight, be sure to retighten after your first couple rides.

Installing Your Front Fender

1. Align the fender clamps on the left and right legs of the fork with fender stay to enable fender in the line with the wheel. Fix the stay with screws (M5 screw) provided on the clamp.
2. Put the lifting lug of the fender behind fork gantry installing hole. Link and secure these two pieces with the fixing screw (M6 screw) and washer.

Installing Your Pedals

1. Warning: Incorrect installation will cause damage. Please read the instructions and watch our videos if needed.
2. Identify the Left and Right markings on the pedals. They can only be installed in their respective side.
   • L is for the Left Pedal and it goes on the Left Crank Arm.
   • R is for the Right pedal and it goes on the Right Crank Arm (Chain Side).
3. Sitting on your bike the pedals go on the Left and Right side respectively.
4. Keep the pedal Horizontal while hand screwing to get the thread started. Then Use your 15mm wrench to tighten them.
5. Both pedals tighten towards the front of the bike. The left pedal is reverse threaded to allow this.
6. The pedals need to be very tight(at least 25-35N.m torque), be sure to retighten after your first couple rides.

Preparations Before Riding

1. Read all instructions carefully, be familiar with the proper operation of all items. Check for detailed information and guidance on our product page.
2. Warning: Basic electric precautions should always be followed to avoid issues or malfunction.

How to Use the Display

1. Power on/off
   Press the button to turn on the display. Your bike will be ON. Press again to turn it off. The display will automatically shut down when there is no operation or riding for 10 minutes.

2. Adjust the assist level
   Short press the “+” or “-” button to change the assist level from 0 to 5. 0 is without assist. 5 is the max assist level.

3. Walking mode
   Press and hold “-” button for 2 seconds to shift into walking mode; release the button to exit the walking mode. The walking mode function can only be used when the user pushes the e-bike, please do not use it when riding.

4. Headlight on/off
   Press the HEADLIGHT button to turn on the front light. Pressing the HEADLIGHT button again to turn off the headlights

5. Battery indication
   When the battery voltage is high, the five LED power indicators are all on. When the battery is under voltage, the last power indicator flashes for a long time, indicating that the battery is seriously under voltage and needs to be charged immediately.

USB port
For some version, there is USB charge port on the left side of handlebar which you can connect to charge your cellphone.

Cruiser Control Function
The cruise control feature can be used to maintain a desired speed without using the Throttle or Pedal Assist.

To activate the Cruise Control function:
Use the throttle or pedal assist to reach your desired speed. While holding the throttle in a stable speed (speed should be over10mph) over 5 seconds, it will enter into cruise mode. Under cruise mode, the current speed will be maintained without the need to use the throttle or pedal assist.

Deactivating the Cruise Control
To discontinue the use of the cruise control function you can do the following actions:

• Use the brakes by squeezing the brake lever
• Use the throttle

Removing the Battery

To Remove the Battery

1. Turn off LCD display, turn off battery switch on the top of battery.
2. Use your left hand to turn the key clockwise to unlock the battery.
3. Use your right hand to push the battery backward and take out the battery.

Note: the battery weighs heavy and should be handled with care.

When the Battery is Removed

• Do not touch the “+” and “-” terminal contacts on the top of the battery when the battery is removed from the bike.
• Be careful not to drop or damage the battery when loose from the bike.
• Avoid damaging the exposed connector terminals and keep them clear of debris.

How to Charge Your Bike

The battery can be charged when locked on the bike or unlocked and removed from the bike. Before Charging, please turn off the battery switch.

1. Remove the rubber cover on the charging port and insert the charger into the charging port.

2. Plug the charger into an appropriate power outlet. When the charger is plugged in, the red light on the charger will illuminate to show that the battery is charging.

3. Charge the battery, making sure not to charge for longer than 12 hours at a time. When the battery is fully charged, the LED will turn green and charging will be stopped.
   Note: The charger is designed to automatically stop charging when the battery is full, but unnecessary wear of the charging components could occur if the charger is left attached to the battery and a power source for longer than 12 hours. Detach the charger as soon as possible once the green light indicates a complete charge, to avoid unnecessary wear of charging components.

4. Once the battery is charged, unplug the charger from the power outlet.

5. Unplug the charger from the battery. Store the charger in a safe place for future use.

Do not leave a charging battery unattended. Never charge a battery for more than 12 hours at a time. Failure to follow battery charging best practices could result in unnecessary wear to the charging components, battery, and or charger, and could lead to an under-performing or non-functional battery and replacement will not be covered under warranty.

Notes of Charging and Storage

1. Pay attention to checking whether the surface temperature of the battery case rises too high during charging. It is FORBIDDEN to cover the battery during charging.
2. Due to the high temperatures in the summertime, it is NOT advisable to charge it immediately after riding. In winter, it is FORBIDDEN to charge the battery in an environment below 0 ℃. It is recommended to charge the battery in room temperature.
3. If the battery will not be used for a long period, take it off the bike and discharge its capacity to 60%-80% for the stock. Disconnect it from the charger and place it in a dry, ventilated place without direct sunlight. In order to maintain a long lifecycle, it is recommended to charge the battery every two months.

Error Code

When the e-bike electronic control system fails, the display will automatically flicker the LED light to indicate the error code.Below is the error codes list.

position on start-up. Check to see if the throttle can return to the start position or if there is something blocking the throttle unit. Contact technical support.
Light 2 flickers| Throttle Fault| Throttle may be damaged. Check the throttle or throttle cable for damage.

Contact technical support.

Light 1 and light 2 flicker| Over Voltage Protection| The battery voltage is too high to operate. Incorrect battery was used on the bike.

Check to be sure that the correct battery is being used on the bike. Contact technical support.

Light 3 flickers| Motor Hall Signal Fault| At least one of the motor’s hall sensor wires have been disconnected or damaged.

Disconnect and reconnect the motor cable.

Contact technical support.

Light 1 and light 3 flicker| Motor Phase Line Fault| At least one of the motor’s phase wires has been disconnected or damaged.

Contact technical support.

Light 2 and light 3 flicker| Temperature Sensor Fault| The controller’s temperature sensor has become disconnected or damaged.

Contact technical support.

Light 1,light 2 and light 3 flicker| Current Sensor Fault| The controller’s current sensor has become disconnected or damaged.

Contact technical support.

Light 4 flickers| Speed Sensor Fault| Re-plug motor cable connector. Contact technical support.
All light flicker| Communication Fault| Poor connection between the controller and the display. Check all cable connectors. Check for corrosion damage. Contact technical support.

BASIC TROUBLESHOOTING

Reduced battery range

| Low battery power| Charge battery
Low tire pressure| Inspect tire
Heavy load on bike| Adjust bike load
Driving on rough terrain| Adjust route
Using throttle only| Include pedal assist
Battery does not charge| Charger not properly connected| Inspect connections
Battery temperature| Read the user manual for best practices
Damaged charger| Replace charger
Issue with battery| Contact Support Team
E-bike making strange noises| Loose hardware| Tune-up and inspection needed
Issue on drivetrain| Maintenance needed
Issue with motor| Contact Support Team

To find out more, please visit our website at
www.xprit.com.

References

• XPRIT - Electric Bikes that make your Life Colorized

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>