TECO Pro-9900 Automatic Vibration Measurement and Acceptance Instrument Installation Guide

October 30, 2023
TECO

Pro-9900 Quick Installation Guide

Pro-9900 Automatic Vibration Measurement and Acceptance Instrument

TECO Group 「Pro-9900 Portable Vibration Acceptance Instrument」can be applied in analysis & acceptance of vibration problems for rotary machines. Setup is quick and easy. Technicians just go thru simple steps with Pro-9900 Auto software running on tablet to understand potential vibration issues.
It is an essential tool for technicians working in technical support, maintenance, repair and related fields.

Key Components

TECO Pro 9900 Automatic Vibration Measurement and Acceptance
Instrument

Product contents

a. Tool Box : x1
– xDAQ-600 – x1
– IEPE Vibration Gauge – x1
– Double head screw – x1
– Magnet holder – x1
– Winding line – x1
– Power Bank – x1
– Vibration Pole – x1
– Power Bank – x1
b. Tablet Pack – x1
– Windows Tablet w/keypro – x1
c. Action Pack
(soft case 2 pieces) – x1
d. Power Charger
(for Tablet) – x1

Quick Settings and Connection

TECO Pro 9900 Automatic Vibration Measurement and Acceptance Instrument -
Connection Diagram

  1. Connect the Power Bank to the power jack (DC) of the Smart IoT Gateway xDAQ600, and then turn on the Power Bank. The default password of the tablet is 「demo」.

  2. After the WAN LED (orange) is on and wait for around 30 seconds. Then search Wi-Fi AP and start the Wi-Fi connection.

  3. On the Tablet, please enter【Wi-Fi】mode to find 【TECOM_XXXXXX】 Wi-Fi SSID.
    Then, confirm “XXXXXX” 6-digits are exactly the same as the last 6-digits of MAC address, printed on the serial number label of the Smart IoT Gateway. Select “TECOM_XXXXXX” for network connection. The Tablet will show “Connected” to indicate a successful Wi-Fi connection between the Tablet and the Gateway. This procedure only needs to be done once. The Tablet will automatically connect to the Gateway after on.TECO Pro 9900 Automatic Vibration
Measurement and Acceptance Instrument - Bar Code

  4. Install the magnetic vibration gauge (or w/vibration pole) to the correct position of the device under measure.

  5. After the completion of steps 1 to 4, the Measure and Acceptance procedures by using Pro-9900 Auto software on Tablet is ready.

Illustration: After opening the toolbox, perform the following steps

  1. Connect the Power Back to the the gateway and wait for about 30 seconds for the gateway to start.TECO Pro 9900 Automatic Vibration Measurement and Acceptance Instrument - toolbox 1
  2. Insert keypro into Type C interfaceTECO Pro 9900 Automatic Vibration Measurement and Acceptance Instrument - toolbox 2
  3. Turn on the power on the tabletTECO Pro 9900 Automatic Vibration Measurement and Acceptance Instrument - toolbox 3
  4. Find xDAQ-600 Wi-Fi SSID and connect.TECO Pro 9900 Automatic Vibration Measurement and Acceptance Instrument - toolbox 4
  5. Select PMS APP to openTECO Pro 9900 Automatic Vibration Measurement and Acceptance Instrument - toolbox 5

Prognosis Monitoring System (PMS)
Provide following functions
Projet : Create data for measuring equipment
Monitor : Real-time data capture, health analysis, diagnosis
Data Analysis : Load historical raw data for data diagnostic analysis
Predictive Analysis : Predictive analysis through database data and algorithms
Report Export : Chart trend analysis from database data
Environment Setting : DAQ, channel, database, file, system setting
Judgment every minute, the results are presented numerically, the higher score means the higher probability that the problem will occur.

17 Troubleshooting Items

Shaft  Type Bearing Type Electrical Type Gear Type
Unbalance Oil whirl Air Gap Eccentricity Gear Eccentricity
Shaft Bent Oil whip Broken Rotor Bar Gear Misalignment
Misalignment Inner race damage Phasing Fault Broken Gear Tooth
Looseness Outer race damage Gear Tooth Wear
Roller damage Gear Shaft Bent

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals