SSC-LUXon 990070785 Wall Light Instruction Manual

SSC-LUXon 990070785 Wall Light

Product Information

• Type: Wall light
• Model: ESMA / ESMO
• Protection type: IP54
• Voltage: 220-240 VAC / 50-60 Hz
• Material: Aluminium / protective glass
• Socket: 2 x GU10
• Max. power: 2 x 35 W
• Protection class: I
• Height: ESMO: 140 mm ESMA: 170 mm
• Width: ESMO: 65 mm ESMA: 65 mm
• Depth: ESMO: 110 mm ESMA: 106 mm
• Colour: Black

Product Usage Instructions

1. Disconnect the connecting cable from the power supply.
2. Loosen the screws (2x). Remove the wall mounting plate on the back of the light.
3. Mark out the drill holes with the help of the back plate and drill the holes. Insert the dowels into the drill holes. Guide the connection cable through the round rubber seal (pierce).
4. Screw the back plate to the wall.
5. Connect the connection cables (L, N, and ground, if applicable) to the light.
6. Place the light on the back plate on the wall. Screw the light in place with the two screws.
7. Unscrew the two light covers. Insert the GU10 light sources into the sockets.
8. Screw the two light covers back onto the light. Make sure that the sealing rings are in the correct position.
9. Switch the connection cable to voltage, the product is now ready for use.

Note:
The product is suitable for mounting indoors and outdoors. It may only be mounted on stable and tilt-resistant walls. Do not cover the product under any circumstances, especially not with insulating material, fire hazard! The components of the luminaire and especially the lamps/light source become hot during operation, especially in the case of halogen lamps/light source. Keep a sufficient distance (0.5 m) from easily flammable objects (e.g. curtains, drapes, etc.) and flammable materials (ignition temperature).

Important:
This product is for lighting purposes only. It must not be exposed to strong mechanical loads or heavy soiling and may not be operated after damp or dirty storage until after a condition check. The product may not be changed or modified, otherwise, the operating permit and conformity will expire with immediate effect. It is not allowed to remove the type plate. If these points are not observed, a short circuit or electric shock may occur, which can be dangerous to life.

Intended use

This product is for lighting purposes only and: -can be installed indoors and outdoors -protection type IP54, suitable for use in damp areas-must not be exposed to strong mechanical loads or heavy soiling -may not be operated after damp or dirty storage until after a condition check -may not be changed or modified, otherwise the operating permit and conformity will expire with immediate effect! It is not allowed to remove the type plate.

If the aforementioned points are not observed, a short circuit or electric shock may occur! There is a danger to life!

General safety instructions

• The complete installation may only be carried out by an authorized electrician who is familiar with the applicable guidelines. Hereinafter referred to as „qualified electrician“.
• For safe handling of the product, the user must have read and understood the installation/operating instructions completely before using the device for the first time.
• The product may only be used if it is alright. If the device or parts of it are defective, it must be repaired by a qualified electrician.
• Only use lamps/light sources approved by the manufacturer. The max. lamp wattage in watts is not allowed to be exceeded.
• This product is not a toy and is not allowed to be stored or used within the reach of children.
• Safe operation of the product is only guaranteed if these instructions are followed. Therefore, keep these assembly/operating instructions. SSC-LUXon GmbH accepts no liability if the instructions given here are not followed or the lamp is subjected to improper use.

Assembly & configuration

• Caution: The connecting cable must be disconnected from the power supply before starting work (switch off the main switch/fuse)! Only use parts that are supplied with the product or which are clearly marked as equipment! Otherwise, the product may not be sufficiently safe!
• The cable routing shown in the illustrations is for simplified purposes only. They in no way represent a recommendation for connection! The connection may only be carried out by a qualified electrician.
• When drilling, pay attention to cables and gas and water lines.
• The product may only be mounted radiating upwards and downwards.

Assembly location
The product is suitable for mounting indoors & outdoors. The product may only be mounted on stable and tilt-resistant walls. Do not cover the product under any circumstances, especially not with insulating material, or fire hazards!

The components of the luminaire and especially the lamps/light source become hot during operation. Especially in the case of halogen lamps/light sources. Keep a sufficient distance (0.5 m) from easily flammable objects (e.g. curtains, drapes, etc.) and flammable materials (ignition temperature<250°C)!

Operation, bulb replacement, faults & disorders

Caution:
Disconnect the connecting cable from the power supply before replacing lamps/light sources!

Halogen lamps/light sources become very hot during operation – risk of burns! Therefore, do not touch the protective glass or the reflector! Allow to cool down before replacing! Do not cover! There is a risk of fire when covering (e.g. with towel)! Lamps with protective cover may only be operated with complete protective cover!

Never look directly into the light source!

What to do in case of error?
In case of an error, the device must be switched off immediately. The product may only be operated if it works correctly. The device may only be put back into operation after it has been checked by a qualified electrician! This is the case if:

1. There is visible damage
2. The product is not working corrctly
3. There is smoke, steam, or audible crackling noises
4. Overheating can be detected

Caution:
There is a danger to life – repairs to the product or work on parts carrying mains voltage may only be carried out by qualified electricians.

Avoidance of disturbances and fire hazards:
It is not allowed to cover the product under any circumstances. Air circulation must be ensured. Nothing may be attached or hung on the product, especially no decoration.

Cleaning & care instructions

The product may only be wiped dry or carefully with a slightly damp and lint- free cloth. The product is not allowed to be removed for this purpose. Do not use abrasive or sharp objects or aggressive cleaning agents. Do not use solvents.

Technical data & assembly instructions

Technical data & assembly instructions ESMA & ESMO – 990070785 & 990070786

1. Disconnect the connecting cable from the power supply. Fig.1
2. Loosen the screws (2x). Remove the wall mounting plate on the back of the light. Fig.2
3. Mark out the drill holes with the help of the back plate and drill the holes. Insert the dowels into the drill holes. Guide the connection cable through the round rubber seal (pierce). Fig.3
4. Screw the back plate to the wall.
5. Connect the connection cables (L, N and ground, if applicable) to the light. Fig.4
6. Place the light on the back plate on the wall. Screw the light in place with the two screws. Fig.5
7. Unscrew the two light covers. Insert the GU10 light sources into the sockets. Fig.6 & Fig.7
8. Screw the two light covers back onto the light. Make sure that the sealing rings are in the correct position. Fig.8
9. Switch the connection cable to voltage, the product is now ready for use. Fig.9

Type/Wall light

• Model: ESMA / ESMO
• Protection type: IP54
• Voltage: 220-240 VAC / 50-60 Hz
• Material: Aluminium / protective glass
• Socket: 2 x GU10
• Max. power: 2 x 35 W
• Operating temperature: -20°C – +35° C
• Protection class: I
• Height:
  • ESMO: 140 mm
  • ESMA: 170 mm
• Width Ø:
  • ESMO: 65 mm
  • ESMA: 65 mm
• Depth:
  • ESMO: 110 mm
  • ESMA: 106 mm
• Colour: Black

Notes/explanations & legend

Important information

• Disconnect the device from the mains power before starting any work
• Protection class I
• Installation only by qualified electrician
• Vers. 06/2020

Notes on use indoors & outdoors

• Protection type IP2X: Use only indoors and dry, i.e. do not use in damp or dirty rooms and in areas of high humidity.
• Protection type IP4X, IP5X & IP6X: Can be used indoors and outdoors.

Onlineshop:
www.led-lichtraum.de.

Satisfied with your product?
Then we look forward to your product review in our online store, on Amazon or eBay!

Disposal instructions
Make sure to dispose of the packaging in accordance with the applicable guidelines of your local authority. Devices marked with the crossed-out waste garbage do not belong in the household waste! You are obliged to hand in these devices at one of the free collection points in your municipality. You can obtain more information from your local authority, the relevant town hall, or a local or regional waste disposal company.

• Keep packaging material and small parts away from children and animals. The danger of suffocation!

SSC-LUXon GmbH
Am Krozinger Weg 4, 79189 Bad Krozingen, Germany
E-Mail: service@ssc-luxon.de
Phone: +49 7633 – 988 3000

References

• Luxon EDV GmbH
• LED Leuchten & Lampen online kaufen bei LED-Lichtraum

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>