Outsunny 342-049V70 7-in-1 Bouncy Castle Instruction Manual

: October 30, 2023
: Outsunny

Table of Contents

Outsunny 342-049V70 7-in-1 Bouncy Castle
Product Information
Product Usage Instructions
SET-UP/INSTALLATION
DEFLATION AND FOLDING
WATER PIPE SET UP INSTRUCTION
INSTALLATION OF THE WATER PIPE CONNECTOR
MAINTENANCE AND REPAIR
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Outsunny 342-049V70 7-in-1 Bouncy Castle

Outsunny-342-049V70-7-in-1-Bouncy-Castle-product-img

Product Information

The product is a water slide with multiple sprinklers that vary in quantity based on the model. The product has serial numbers on each sprinkler to match the product model. The water pipe needs to be wrapped along the velcro line after confirming the position of each sprinkler.

Imported by Aosom LLC 27150 SW Kinsman Rd Wilsonville, OR 97070USA-MADE IN CHINA
Imported by Aosom Canada Inc. 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9 MADE IN CHINA

Product Usage Instructions

Unpack the product and locate the serial numbers on each sprinkler.
Match the serial numbers on each sprinkler to the product model.
After confirming the position of each sprinkler, wrap the water pipe along the velcro line (5).
Connect the water hose to the water slide and turn on the water supply.
Ensure that the water is flowing through each sprinkler and adjust them if necessary.
Enjoy using the water slide.

WARNING

Children can drown in very small amounts of water. Empty the pool when not in use.
Not suitable for children under 3 years old. Small parts. Choking hazard. Long Cord. Strangulation hazard.
Do not install the padding pool over concrete, asphalt or any other hard surface.
Only for domestic use.Indoor use or outdoor use is accepted.
Keep the installation instruction for further reference. Please read all safety rules before setting up.

WARNING ELECTRICALLY OPERATED PRODUCT

Adult supervision is required. As with all electrical products, precautions should be observedwhen handling and using the device. To avoid electric shock, follow these basic guidelines:

Keep away from fire. Keep the blower away from water during use.
Do not disconect the blower during use.
Do not use in bad weather conditions.
Check the general condition of the device and the power sources before each use. Ifyou notice a defect do not use it under any circumstances.

SET-UP/INSTALLATION

Outsunny-342-049V70-7-in-1-Bouncy-Castle-fig-1

A: Check that the ground is clear of any object or debris. Unfold the structure, install it on a flat and tender surface, with a safety distance all around 2 meters minimum.
B: Place the blower in a dry place, away from any water source and make sure ii is still. Streich the inflation tube and attach it to the end of the blower. The inflation tube should be straight and untwisted. Connect the blower to an electrical outlet and press ON. The structure inflates quickly. The blower must stay on all the time while using the product.
C: Firmly push the slakes into the ground at the straps localed at the base of the inflatable structure to maintain the structure during use.

DEFLATION AND FOLDING

Outsunny-342-049V70-7-in-1-Bouncy-Castle-fig-2

Make sure all children exit the product.
Makes sure the product is free from foreign objects.
If there is water inside the seams after used the water pool, keep the air blower at work for about 30 minutes to dry that out before packing.
If the product comes with water bags, please follow the undermentioned instruction, otherwise, overleap this point. Detach the water bags from the product. Remove the product and blower before opening the stopple for draining. Empty water in the water bags and dry them in cool place for next time’s use.
Turn the blower(air pump) power switch to OFF. (refer to pictureD)
Unplug the blower(air pump) power cord.
Loosen the Velcro and detach the inflation tube from the blower. The product should deflate on its own within 5 minutes. Make sure the product is entirely deflated.
Remove ground support stakes.
Fold the product in half from both ends, and then fold it in half 2 more times from both sides, vertically to the first fold. (refer to pictureE,F, G H)
Roll it up tightly from the end opposite the inflationtube. (refer to picturel,J K)
Slip the carry bag over the folded product and stakes (plastic balls or water bags ). Zip the bag. (refer to picture L)

WATER PIPE SET UP INSTRUCTION

Parts List: Water pipe (3), Sprinklers (1. 2)
Di erent water slide have di erent quantity of sprinklers, thus, there are serial numbers on each one to match the product. No.1 will match the No.1, and No.2 match the No.2. After confirming the position of each sprinkler, please wrap the water pipe along the velcroline (5)
Find the hose connector when finish fixed the water pipe. Then connect the hose connectoro the end of a standard home hose refer below installation way.

Outsunny-342-049V70-7-in-1-Bouncy-Castle-fig-6

INSTALLATION OF THE WATER PIPE CONNECTOR

Put the hose clamp to your own water pipe, like pies 1.
Find the connector and connect it to your own water pipe like pies 2, the front of the connector should be covered oompletely by your own water pipe in order to avoid spillage when the water pressure is too high.
After connected the water pipe properly, please use the hose clamp lock the water pipe. When using the hose clamp, use one hand to pinch the iron part and twist the hose clamp handle clockwise with your other hand until it completely locks he water pipe. Like pies 3.

MAINTENANCE AND REPAIR

Maintenance: Checks and maintenance must be carried out at regular intervals on the structure to avoid damage or leakage. The product can be cleaned with a mild detergent. Always keep water away from the air blower. Do not store the product when it is wet. Store the product and the blower indoors in dry conditions when not in use.
Repair: A repair kit is supplied with each structure. If the fabric tears, please repair by sewing by hand. Cover the tear with a suitably sized piece of fabric from the kit. Then sew the repair fabric to its sides. When repairing, sewing should only take place on the surface layer of the original fabric and not reach its bottom layer. In the event of a large tear or internal structural damage, please change the structure or entrust the repair to a professional. It is not suggested to patch the same repair more than twice. The needles must be well maintained and must not be left on the product after sewing.

IMPORTER

Imported by Aosom LLC 27150 SW Kinsman Rd Wilsonville, OR 97070 USA MADE IN CHINA