Advanced Media Technologies KEMPII SHELLBOX User Guide
- October 30, 2023
- Advanced Media Technologies
Table of Contents
SB-KEMPII-SB
KEMPII SHELLBOX
User Guide
DESCRIPTION
AMT vaults are designed based on the highest demands of mechanical and
environmental resistance, providing an excellent protection performance for
underground installations in the electrical, energy and telecommunication
sector. Its modular assembly facilitates transportation, storage and
installation.
This product is made from recycled polyethylene bags, on strength of the
commitment we have of contributing to the ecological balance.
Provides high load capacity, flame retardant protection, resistance to
sunlight, abrasive wear, resistance to a variety of chemical agents, in
addition to its design, made and tested under international standards.
CHARACTERISTICS
- Manufactured with a modular body of low density polyethylene, fully recycled, while maintaining excellent resistance.
- It is recommended to be used in telecommunications, energy, and electrical substations.
- The cover is secured with galvanized metal hexagonal screws and has handles on the sides for better handling and opening.
- Self-extinguishing material, resistant to solar radiation and abrasion.
- Provides protection against a wide range of chemical agents such as: acids, ketones, solvents, gasses, water vapor, etc.
- Its modular design allows it to be easily transported, stored and assembled.
- Withstands loads of up to 25 tons in compression and tension.
- Optimum to be installed in different environments such as sidewalks, gardens or vehicular streets with intense and heavy traffic.
- Structural design with lateral cavities provides greater support and subterranean anchorage, allowing walls up to 2 inches thick.
TECHNICAL SPECIFICATIONS
General register
Parameter | Value |
---|---|
Distributed load capacity | 25 tons |
Point load | 17 tons |
Fatigue strength | 1000 cycles with 14.5 Kgf |
Flexion | 26 mm, 15 Tons |
Manufacturing material | Low density polyethylene |
Total weight (cover and register) | 40.9 Kg |
General dimensions | Width |
Length | 63 cm |
Height | 55 cm |
Low Density Polyethylene
Nomenclature (Spanish/English)| PEBD/PELD
Density| 0.922 g/cm3
Breaking strain| 20/20 Mpa
Elongation at breaking point DM/DT| 380/910 %
Impact resistance| 230 g/F50
NORMATIVITY AND STANDARDS
ALT’s modular registers are manufactured in full compliance with the following standards, endorsed and certified by the Equipment and Materials Testing Laboratory LAPEM.
Specification | Test load |
---|---|
lbf | kN |
American
Pedestrian/Light Duty| 3000| 14
ANSI/SCTE 77 TIER 22| 22500| 100
ANSI/SCTE 77 TIER 15| 33750| 150
APAC
AS3996-Class C| 3370| 15-Jan
AS3996-Class B| 18000| 80
Pedestrian/Light Duty| 33750| 150
EMEA
Pedestrian/Light Duty| 2250| 10
EN 124 Class B125| 28100| 125
EN 124 Class C250| 56202| 250
PARTS LIST
Part | Quantity | Code |
---|---|---|
50×55 cm side panels | 1 piece | MI-KEMPII-SB |
Lower frame | 2 pieces | L60-KEMPII-SB |
60×55 cm side panels | 2 pieces | L50-KEMPII-SB |
Top frame | 1 piece | MS-KEMPII-SB |
Galvanized hexagonal screws | 1 piece | T-KEMPII-SB |
Cover | 4 pieces | – |
2 1/2” screws | 10 pieces | – |
DIMENSIONAL SCHEME
Dimension | Exterior | Interior | Unit |
---|---|---|---|
Width | 530 | 448 | mm |
Length | 630 | 548 | mm |
Height | 550 | 412 | mm |
ASSEMBLY STEPS
1. Place the lower frame on the floor.| 2. Install one of the 60×60 cm
square sidewalls on the frame, using a mallet.| 3. Place one of the 60×90 cm
rectangular side panels on the
other side of the frame, taking into account the coincidence
of the male-female assembly of its edges.
---|---|---
4. Repeat the previous step with the same type of frame,
alternating the assembly of the edges.| 5. Install the last square side in
such a way it fits correctly with the rest of the previously installed faces.|
6. Install the top frame. .
7. Place the 10 screws of 2 1/2” to adjust the top frame to the side faces.
The figure shows how to install.| 8. Place the cover on the frame using the
handles.| 9. Finally install the 4 hexagonal screws in the corners of the
cover.
ORDER CONFIGURATION
SB-KEMPII-SB
VERSION CONTROL
Ver. No. | Date | Description | Revised by | Approved by |
---|---|---|---|---|
00 | 21/02/2022 | Original emission | Martín S. M. | Alicia Soto |
Version: 00
Date: 21/02/2022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>