MAGNUM FIRST MZ-ASW1 Self Powered Wireless Switch With Dimming Capabilities User Guide
- June 10, 2024
- MAGNUM FIRST
Table of Contents
MZ-ASW1 / ASW2 (ZigBee)
Self Powered Wireless Switch With Dimming Capabilities
User Guide
Self-powered wireless controls are simple to install.
Magnum Single and Double Rocker Pads use radio frequency technology to communicate wirelessly with other Magnum devices and provide convenient control of lighting, temperature and miscellaneous electric loads. The rocker pads are self-powered and never require batteries because the simple act of pressing the rocker generates enough energy to send a signal to other Magnum devices. Use them in conjunction with Magnum sensors and controls to maximize efficiency and provide a level of comfort and convenience you cannot achieve with traditional switches. Magnum products feature clean contemporary styling, making them an attractive addition that’s sure to compliment any décor.
Features & Benefits
- Communicates wirelessly with other Magnum devices using a Zigbee radio modules
- Wireless – no additional wire to run so installation is fast and easy. Install them where you want them and then move them anytime.
- Self-powered – no batteries to replace and no on-going maintenance.
- Decorator style rocker pads capable of performing switching and dimming functions.
SPECIFICATIONS
Part Number
(ESRP=Single Rocker)
(EDRP=Double Rocker)| MZ-ASW1
MZ-ASW2
---|---
Power Supply| Electrodynamic harvesting
Inputs / Outputs| • 1 or 2 button rocker switch options
• Radio Frequency (RF) transmitter
Transmission Range| typ. 328 ft (100 m) free field / 32.8 ft (10 m) indoor
RF Transmission| On press and release of rocker button
Dimensions| Single: 3.8” H x 3.4” W x .85” D
Double: 3.8” H x 3.5” W x 85” D
Weight| Single: 3.5oz.
Mounting| Surface mounted on wall (using included mounting screws) Can also be
flush mounted by optional use of electrical wall box or low-voltage ring
Environment| • Indoor use only
• 32° to 131° F (0° to 55° C)
• 5% to 95% relative humidity (non-condensing)
Agency Listing| FCC, I.C.
Commissioning
Part 1
Activate commissioning (or linking) mode for a system compatible with the
switch.
If you don’t know how to do this, consult the manual for the compatible system
or contact the manufacturer for assistance.
Part 2
Put the switch into commissioning mode.
To enter commissioning mode, start by selecting one button on the switch. (Use
the same button for the entire sequence.
Pressing any other button will exit the commissioning mode.)
Next, execute the following long-short-long sequence:
- Press and hold the selected button for more than 7 seconds before releasing it
- Press the selected button quickly (hold for less than 2 seconds)
- Press and hold the selected button again for more than 7 seconds before releasing it The switch has now entered commissioning mode.
Part 3
Linking the switch to the compatible system.
A radio signal needs to be sent from the switch to the compatible system on
the correct ZigBee channel. The system uses one of sixteen possible channels,
automatically set by the system. Using the switch, a signal will be sent on
each channel until the channel used by the compatible system is found. Upon
entering commissioning mode, the switch sends a signal on the currently
selected channel. The signal is sent on the default channel 11, unless the
switch had been put on another channel previously. (This allows linking
additional devices without changing the currently used radio channel.)
Here is a chart of the ZigBee channels and the corresponding radio
frequencies (in MHz).
Channel ID| Lower Center| Upper Frequency| Frequency
Frequency
---|---|---|---
11| 2404| 2405| 2406
12| 2409| 2410| 2411
13| 2414| 2415| 2516
14| 2419| 2420| 2421
15| 2424| 2425| 2426
16| 2429| 2430| 2431
17| 2434| 2435| 2436
18| 2439| 2440| 2441
19| 2444| 2445| 2446
20| 2449| 2450| 2451
21| 2454| 2455| 2456
22| 2459| 2460| 2461
23| 2464| 2465| 2466
24| 2469| 2479| 2471
25| 2474| 2475| 2476
26| 2479| 2480| 2481
Cycle through the sixteen channels
To change the switch’s channel, short press the selected switch button (less
than 7 seconds) once after entering commissioning mode. This will reset the
channel used by the switch to channel 11.
If the switch was already operating on channel 11 (default condition) then the
radio channel will remain unchanged. This ensures that the switch will always
use channel 11 as the starting point for the channel adjustment.
Short press the selected button (less than 7 seconds) again to move to the
next channel. For each such button press,
the switch transmits on the next channel. If channel 26 has been reached then
channel 11 will be used next.
When the switch is on the correct channel, the compatible system will provide
a link confirmation indication. Consult the instructions for the compatible
system for details of the link confirmation indication. There should be a
visible or audible exchange indicated on the system, and the switch will be
linked to the system.
Exit linking mode on the switch by pressing any other button on the
switch.
For problems with the compatible system, please contact the system provider.
Magnum First – 1 Seneca Street, 29th Floor, M55 – Buffalo,
NY 14203 – phone716-293-1588
www.magnumfirst.com –
info@magnumfirst.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>