Jiaxing JX-80 True Wireless Stereo Earphone User Manual

JX-80 True Wireless Stereo Earphone
User Manual

Thank you for purchasing this product, this product has fashionable appearance and high-end sound quality. Before using this product, please read and strictly follow the instructions and precautions, and keep it for future reference.

PRODUCT DIAGRAM

Pls full charge the earbuds and charging box before first using!

Product description

1. After the headphones are taken out of the charging compartment, they will automatically start up and form a team. The mobile phone can directly search  for the device connection.(wait 8 seconds for the first search)
2. 5V adapter shall be used to charge the charging compartment and earphone.  Itis forbidden to use the adapter with voltage higher than 5V  Fast charging or other adapters,
3. When the earphone cannot be charged when it is put into the charging  compartment, please check whether there is power in the charging  compartment first, or use a rag. Wipe the charging contact point of the earphone, and then put it into the charging compartment to charge the earphone
4. When the earphone is abnormal during use, for example, there is only sound on ones side, you can Put the two earphones into the charging compartment,  charge them for 3-4 seconds, then take them cut and reconnect them
5. When used alone, put the other earphone in the charging compartment

Warning: It is strictly prohibited to place the product in an overheated or  under cooled place. The temperature higher than 50 C or lower than 10 C will affect the battery performance.

Starting/Pairing/Connecting

1. Starting
   Take out the earphone from the charging compartment, and see the LED flashing, that is, the earphone is automatically turned on successfully.
   In the off state, ling press the left and right touch buttons  for 3seconds to turn it on  In the power on state, long press the lef: and right touch buttons for 4 seconds to shut down

2. Pairing
   Take out the earphones on both sides from the charging compartment,  and the earphones will start automatically The earphones on both sides will be paired automatically.
   When the headphones are outside the charging compartment and in the off state, press both headphones at the same time  Press the multi-function button for 3 seconds, and the headset  will be turned on and paired automatically.

3. Connecting
   Automatic connection: take the headset out of the charging box  and wait for 2-3 seconds for automatic connection,  Pen the device Bluetooth, search for “jx-80”, and click Connect, Manual connection: press the multi-function keys on both earphones at the same time for 3 seconds, and the earphones will turn on And automatically pair. Turn on Bluetooth to search for connection. If the connection fails, turn off Bluetooth and repeat the above operation.

Earbuds charging
When the headset is charged,  there light is always on; when the headset is fully charged, the light is off

Charging box charging
When charring%the charging  bin, the red  light flashes slowly. When the charging bin is fully charged, there light  is always on
Charging port Type-C
Method of wearing

Clip the wrongheadedness the auricle like  ear clips.  After wearing, adjust the position of headphones until the  sound effect is the best. Fora clear position. Earning  headphones have a small ball in front and a big ball in front. After. Be careful motto battlefront and back wrong.
Touch location and operation mode

Touchstone of the left and right headphones.
You can perform basic operations by fingerprint touch
FCC statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>