i-PRO WV-QCD100 Ceiling Mount Bracket Instruction Manual
- June 10, 2024
- i-PRO
Table of Contents
Ceiling Mount Bracket
Model No. WV-QCD100
Instruction Manual
WV-QCD100 Ceiling Mount Bracket
- Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
- The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage
resulting from failures arising out of improper installation or operation
inconsistent with this documentation .
“<Control No.: C**>” used in these documents should be used to search for
information on our technical information website (
https://i-pro.com/global/en/surveillance/training-support/support
/technical-information** ) and will guide you to the right information.
Caution:
- Before attempting to connect or operate this product, please read these instructions carefully.
Notice:
- This product is not suitable for use in locations where children are likely to be present.
- Do not install this product in locations where ordinary persons can easily reach.
Precautions
-
Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents. -
Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
Be sure to consult the dealer. -
The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.
When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.
About notations
Some functions are expressed with the following notations in this document.
Clear dome cover
Smoke dome cover
Preface
This product is a ceiling mount bracket that is designed to mount the indoor
PTZ type camera on a ceiling.
The latest information about the supported cameras
Specifications
| Ambient temperature: | –10 °C to +50 °C {14 °F to 122 °F} |
|---|---|
| Dimensions: | Maximum diameter ø185 mm × 163 mm (H) |
{ø7-9/32 inches × 6-13/32 inches (H)}
Mass:| Approx. 230 g {0.51 lbs.}
Finish:| Main body: ABS resin i-PRO white
Dome cover: Acrylic resin (Transmittance: approx. 50 %)
Precautions for installation
-
In order to prevent injury, the product must be securely mounted to the camera according to the Installation Guide of this product.
-
This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water and moisture. -
Make sure to remove this product if it will no longer be used.
Standard Accessories
Operating Instructions (this document) …………1 pc.
The following are for installation.
Inner cover (WV-QAT100) ………………………….1 pc.
Parts and functions
-
If a tiepin type microphone is used, mount the microphone on the rubber-made microphone stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.
IMPORTANT:- To prevent injuries and protect the cables, finish the side cable access hole with a file to avoid sharp edges.
Installation
Refer to the operating instructions of the camera for details on the camera
installation (including the camera mounting, cable connection and adjustment).
Step 1
Attach the inner cover.
- Remove the side covers from the camera main body. (Both the left and right sides)
- Attach the inner cover.
„ When removing the inner cover
Release the claws on the inner surface on both the left and right sides one by
one and then remove the inner cover.
Step 2
Mount the camera.
The camera shall be mounted on the camera mounting bracket (supplied with
the camera) after mounting it on a ceiling.
For further information, refer to the Installation Guide of the camera.
Step 3
Install this product to the camera mounting bracket.
-
Connect the safety wire attached on this product to the safety wire hook.
Make sure that the apical ring of the safety wire is engaged with the safety wire hook of the camera mounting bracket by pulling the safety wire after connection.
-
Mount this product on the camera with aligning the projection of the camera mounting bracket (2 places) with “OPEN” of this product (2 places). Note:
• Make sure to face the product in a direction its i-PRO logo aligns with the one on the camera.
IMPORTANT:
• Use caution not to catch the cables. -
Turn this product clockwise until the projection of the camera mounting bracket aligns with “LOCK” of this product.
Step 4
Remove the protection sheet from the dome cover.
Note:
- When the tilt angle of the camera is almost level, the upper side of images will be hidden by this product reflecting on the screen. In such a case, adjust the tilt angle. Refer to the Operating Instructions of the camera for further information.
https://i-pro.com/global/en/surveillance/training-
support/support/technical-
information
i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022 Ns0522-0
Printed in China
Documents / Resources
|
i-PRO WV-QCD100 Ceiling Mount
Bracket
[pdf] Instruction Manual
WV-QCD100 Ceiling Mount Bracket, WV-QCD100, Ceiling Mount Bracket, Mount
Bracket, Bracket
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>