i-PRO WV-S61501-Z1 Network Camera User Manual

WV-S61501-Z1 Network Camera

Product Information

The product is a network camera available in different models:
WV-S61501-Z1, WV-S61301-Z2, WV-S61301-Z1, WV-U61301-Z2, and WV-U61301-Z1. The camera comes with different functions that are supported by specific models. The product is provided without any warranty, and technical inaccuracies or typographical errors may exist in the publication. The network camera requires specific system requirements for a PC to function.

Usage Instructions

When using the product, it is essential to take precautions against security risks such as leakage or theft of information, illegal operations, and interference or stoppage of the unit by persons with malicious intent. To prevent unauthorized access, change passwords regularly and do not use the camera in hot and humid conditions or expose it to direct heat sources such as a heater. Handle the product with care and avoid dropping, applying shock or vibration to it. Do not touch the dome cover with bare hands to prevent deterioration of picture quality.

If an error is detected, the product will restart automatically and will be inoperable for about two minutes. The camera has an automatic status detection function that restarts the product when it malfunctions due to exogenous noise for 30 seconds or more. If the product repeatedly resets, contact the dealer for instructions.

About the user manuals
Product documentation is composed of the following documents.

• Installation Guide (accessory): Provides information about “Precautions”, “Precautions for installation” and the installation method.
• Basic Information (this document): Provides information about “Precautions for use”, “Parts and functions” and “Detail specifications”.
• Operating Instructions (Refer to the link on the following product information website): Explains how to perform the settings and how to operate this camera.
  https://i-pro.com/global/en/surveillance/training-support/documentation- database-list

“<Control No.: C****>” used in these documents should be used to search for information on our technical information website
(https://i-pro.com/global/en/surveillance/training-support/support/technical- information) and will guide you to the right information.

• microSDXC/ microSDHC/ microSD memory card is described as microSD memory card.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.

Limitation of liability
THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY’S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).

Disclaimer of warranty
IN NO EVENT SHALL i-PRO Co., Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:

1. ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;
2. ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;
3. ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE MALFUNCTION OR TROUBLE;
4. INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
5. ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
6. ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION AS A PHOTOGRAPHED SUBJECT DUE TO VIOLATION OF PRIVACY CONCERNING A SURVEILLANCE CAMERA’S PICTURE OR SAVED DATA, FOR SOME REASON (INCLUDING USE WHEN USER AUTHENTICATION ON THE AUTHENTICATION SETTING SCREEN IS SET TO OFF), BECOMING PUBLIC OR BEING USED FOR ANY PURPOSE;
7. LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE (INCLUDING INITIALIZATION OF THE PRODUCT DUE TO FORGOTTEN AUTHENTICATION INFORMATION SUCH AS A USER NAME AND PASSWORD).

About notations
The following notations are used when describing the functions limited for specified models. The functions without the notations are supported by all models.

• 61501Z1: The functions with this notation are available when using the WV-S61501-Z1 series.
• 61301Z2: The functions with this notation are available when using the WV-S61301-Z2, WV-U61301-Z2 series.
• 61301Z1: The functions with this notation are available when using the WV-S61301-Z1, WV-U61301-Z1 series.

System requirements for a PC

• CPU: Intel® CoreTM Processor family

  • Intel® CoreTM i5-6500 or faster
  • Intel® CoreTM i7-6700 or faster recommended

• Memory: 4 GB (2 GB x 2, Dual Channel) or more recommended.

• Network interface: 10BASE-T/100BASE-TX 1 port

• Audio interface: Sound card (when using the audio function)

• Monitor: Image capture size: 1024 x 768 pixels or more
  Color: 24-bit True color or better

• OS: Microsoft Windows 11
  Microsoft Windows 10

• Web browser: Microsoft Edge
  Firefox
  Google ChromeTM

• Others: Adobe® Reader® or Acrobat Reader®
  (It is necessary to view the PDF file.)

IMPORTANT:

• For information on the operation verification of web browsers, refer to our technical information website .
• When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inoperable.
• Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted depending on the network environment.

Network security
As you will use this unit connected to a network, your attention is called to the following security risks.

1. Leakage or theft of information through this unit
2. Use of this unit for illegal operations by persons with malicious intent
3. Interference with or stoppage of this unit by persons with malicious intent

It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.

• Use this unit in a network secured by a firewall, etc.
• If this unit is connected to a network that includes PCs, make sure that the system is not infected by computer viruses or other malicious entities (using a regularly updated anti-virus program, anti-spyware program, etc.).
• To prevent unauthorized access, use user-authentication, set user names and passwords, and limit which users can log in.
• Apply measures such as user authentication to protect your network against leakage or theft of information, including image data, authentication information (user names and passwords), alarm mail information and DDNS server information.
• After the unit is accessed by the administrator, make sure to close the browser.
• Change the administrator password periodically. Additionally, save user authentication information (user names and passwords) in such a way that it is kept out of the hands of third parties.
• Do not install the camera in locations where the camera or the cables can be destroyed or damaged by persons with malicious intent.

Precautions for use

When the product is accessible from the Internet
To prevent unauthorized access, note the following.

• Leave user authentication turned on.
• Periodically change passwords that are used to access the product.
  Refer to the Operating Instructions for information about how to change passwords.

To keep on using with stable performance
Do not use this product in hot and humid con-ditions for a long time. Failure to observe this causes component degradation resulting in life shortening of this product. Do not expose this product to direct heat sources such as a heater.

Usage such as switching the power ON/OFF frequently could lead to failure of the camera.

Handle this product with care.
Do not drop this product, nor apply shock or vibration to the product. Failure to observe this may cause trouble.

Do not directly touch the dome cover with your bare hands.
A dirty dome cover causes deterioration of picture quality.

When an error is detected, this product will restart automatically.
This product will be inoperable for around 2 minutes after the restart just as when the power is turned on.

About the automatic status detection function
When this product malfunctions due to exogenous noise, etc. for 30 seconds or more, the product will automatically restart and will return to normal state. When the product is restart, initialization will be carried out as when the power of the product is turned on. When the product repeatedly resets, exogenous noise level around the product may be high and that may cause malfunction. Contact your dealer for instructions.

Periodically images on the screen appear to be distorted
When the camera is installed in a location where it is subject to small vibrations (for example, when it is installed near devices that vibrate), images may appear distorted and stretched lengthways. This phenomenon is a characteristic of image pickup devices that use CMOS sensors and is caused by the relationship between the periodic movements of the camera and the timing that the image sensor reads images. This is not a problem with the camera. To reduce the possibility of this phenomenon occurring, install the camera in a secure location.

We shall not be liable for content compen-sation, losses of recorded or edited con-tent and any direct or indirect consequent damages caused by failure to record or edit due to faults with this unit or the microSD memory card. In addition, the same provisions apply after unit is reparied.

About the CMOS image sensor

• When continuously shooting a bright light source such as a spotlight, the color filter of the CMOS image sensor may become dete-riorated and this may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spot-light for a certain period, the discoloration may remain.
• When shooting fast-moving subjects or performing panning/tilting operations, objects crossing the shooting area may look to be bending askew.

Cleaning this product body
Be sure to turn off the power before cleaning. Failure to observe this may cause injury.
Do not use benzine, thinner, alcohol, or any other types of solvents or detergents. Otherwise, it may cause discoloration. When using a chemical cloth for cleaning, read the caution provided with the chemical cloth product.

• Do not loozen or remove screws unless instructed to do so in the product documentation.
• The camera position may be moved inadvertently while cleaning the camera body. Restart the product or refresh the camera position (position refresh) to correct the camera position. Refer to the Operating Instructions for further information.

Cleaning of the dome cover
Use lens cleaning paper (used to clean camera or spectacles lenses) to remove any dirt on the dome cover.

About the stabilizer function
Depending on the conditions in the installation area, effects of the stabilizer function may not be fully achieved.

Consumable parts
The following are consumables: Replace them in accordance with their operating lifetimes. Their operating lifetimes vary depending on the usage environment and conditions. The oper-ating lifetimes below are just guides for when using the camera at +35 °C {95 °F}.

• Lens unit, panning motor, tilting motor, thin wire coaxial cable, flat cable for tilting: Approx. 3.7 million operations (Approx. 20000 hours)

Do not hold the dome section.
The dome section of this unit rotates. When removing this unit from a ceiling or wall, turn the unit while holding the fixed section.

Motor operating sound
The operating sound may be louder depending on the speed of panning/tilting operations. When you feel uneasy, the operating sound can be diminished by reducing the setting value of auto panning speed.

AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE http://www.mpegla.com

Lens and pan/tilt head
If a lens and pan/tilt head are not performed for a long period of time, the grease coating inside these parts may become sticky. That may obstruct the parts from moving. To prevent this, move the lens or pan/tilt head periodically. Or perform position refresh periodically in the manner described in “Position refresh”.

Position refresh
During the use for a long period of time, the preset positions may become inaccurate. When “Position refresh” is set for the created schedule, the camera position will be corrected periodically.
Refer to the Operating Instructions for how to perform the settings.

Product disposal/transfer
Data saved on this product or a storage device used with this product may lead to personal information leakage. When it is necessary to dispose or give this product to someone, even when for repair, make sure that there is no data on this product.
When abandoning the memory media, it is recommended to destroy it physically after deleting data by PC.
Effects on images and image quality Depending on the installation location, the dome cover may become dirty, causing image quality to deteriorate or images may become difficult to see.

About HEVC (High Efficiency Video Coding) patents
Covered by one or more claims of the HEVC patents listed at patent list. accessadvance.com.

Router
When connecting this product to the Internet, use a broadband router with the port forwarding function (NAT, IP masquerade).
Refer to the Operating Instructions for further information about the port forwarding function.

Time & date setting
It is necessary to set the time & date before putting this product into operation. Refer to the Operating Instructions for descriptions of how to perform the settings.

Parts and functions

The following are descriptions when using the model 61301Z2 .

• Terminals

RJ45 network terminal
Connect an Ethernet cable (category 5e or better, straight, 4 pairs (8 pins)) to the RJ45 network terminal.

IMPORTANT:

• Use all 4 pairs (8 pins) of the Ethernet cable.
• The maximum cable length is 100 m {328 feet}.
• Make sure that the PoE device in use is compliant with IEEE802.3af standard.
• When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V DC will be used for power supply.
• When the Ethernet cable is disconnected once, reconnect the cable after around 2 seconds. When the cable is quickly reconnected, the power may not be supplied from the PoE device.

Power supply terminal (12 V DC) / Power cord plug (accessory)
Connect the output cable of the DC power supply to the power cord plug.

IMPORTANT:

• Be sure to use the power cord plug provided with this product.
• Be sure to fully insert the power cord plug into the power supply terminal (12 V DC). Otherwise, it may damage the camera or cause malfunction.
• When installing the camera, make sure that excessive force is not applied to the power cable.
• Be sure to use an AC adaptor compliant with the Specifications (written in the indication label on the bottom side of this unit) regarding power source and power consumption.

Audio input terminal
Connect a microphone or the line out of an external device using a stereo mini plug (ø3.5 mm).

< For microphone input>

• Recommended microphone (locally procured): Plug-in power type (Sensitivity of microphone: –51 dB to –38 dB (0 dB=1 V/Pa,1 kHz))
• Input impedance: Approx. 2 kΩ (unbalanced)
• Supply voltage: 2.5 V ±0.5 V
• Recommended cable length: Less than 1 m {3.28 feet}

< For line input>

• Input level for the line input: Approx. –10 dBV
• Recommended cable length: Less than 10 m {32.8 feet}

Audio output terminal
Connect an external speaker* using a stereo mini plug (ø3.5 mm). (Audio output is monaural.)

• Output impedance: Approx. 600 Ω (unbalanced)
• Recommended cable length: Less than 10 m {32.8 feet}
• Output level: –20 dBV
• Use a powered speaker.

IMPORTANT:

• Connect/disconnect the audio cables and turn on the power of the camera after turning off the power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
• Make sure that the stereo mini plug is connected to this cable. When a monaural mini plug is connected, audio may not be heard.
  When connecting a monaural speaker with amplifier, use a locally procured conversion cable (mono-stereo).

Note:

• The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on our product information website for descriptions of how to switch the output.

EXT I/O terminals
Note:

• Off, input, and output of the ALARM IN2 and 3 can be switched by configuring the setting. Refer to the Operating Instructions for further information about the ALARM IN2 and 3 settings (“Off”, “Alarm input”, “Alarm output” or “AUX output”).

< Ratings>

• Alarm input1 / Black & white input / Auto time adjustment input, Alarm input2, Alarm input3 Input specification: No-voltage make contact input (4 V – 5 V DC, internally pulled up) OFF: Open or 4 V – 5 V DC
  ON: Make contact with GND (required drive current: 1 mA or more)

• Alarm output, AUX output
  Output specification: Open collector output (maximum applied voltage: 20 V DC)
  OPEN: 4 V – 5 V DC by internal pull-up
  CLOSE: Output voltage 1 V DC or less (maximum drive current: 50 mA)

IMPORTANT:

• Install external devices so that they do not exceed the rating of the network camera.
• When using the ALARM IN2 and/or 3 as the output terminals, ensure they do not cause signal collision with external signals.

Indicators and buttons

• Front side

• Back side

1. INITIAL SET button (Initializing / NTSC ⇔ PAL switch button)
   Follow the steps below to initialize the network camera.

2. Turn off the power of the camera.
   When using a PoE hub, disconnect the Ethernet cable from the camera. When using an external power supply, disconnect the power cord plug (accessory) from the power supply terminal (12V DC).

3. Turn on the power of the camera while pressing the INITIAL SET button, and make sure to release the button after approximately 15 seconds. In about 2 minutes later, the camera will start up and the settings including the network settings will be initialized. Retry if the camera does not start up normally.
   IMPORTANT:

  * When the camera is initialized, the settings including the network settings will be initialized. Before initializing the settings, it is recommended to write down the settings in advance.
  * Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and may cause malfunction.

2. LINK indicator

   • When the camera is able to communicate with the connected device
     Lights orange

3. ACT indicator
   When data is being sent via the network camera
   Blinks green (accessing)

4. SD MOUNT indicator

   • When a microSD memory card is inserted and could be recognized
     Lights off → Blinks green → Lights off

   • When data can be saved after the microSD memory card is inserted and the SD ON/OFF button is pressed (less than 1 second)
     Lights off → Lights green

   • When data can be saved to the microSD memory card Lights green

   • When the microSD memory card is removed after holding down the SD ON/OFF button (about 2 seconds)
     Lights green → Blinks green →
     Lights off (recording)
     Lights green → Lights off
     (waiting for recording)

   • When data cannot be saved to the microSD memory card because an abnormality was detected or the microSD memory card is configured not to be used
     Lights off
     Note:
     Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the installation conditions. (☞ Operating instructions on our product information website)

5. SD ON/OFF button

6. When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights up in green and data can be saved to the microSD memory card.

7. When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights off and the microSD memory card can be removed.

Insert / remove a microSD memory card

Note:

• Use a microSD memory card dedicated to i-PRO cameras.
• Refer to the Operating Instructions on our product information website for further information about the microSD memory card settings.

Insert a microSD memory card

1. Open the SD memory card cover.

2. Insert the microSD memory card until it makes a clicking sound.

3. After the microSD memory card has been inserted, press the SD ON/OFF button, and make sure the SD MOUNT indicator is continually lit.
   If you do not press the SD ON/OFF button after inserting the microSD memory card, the SD MOUNT indicator is automatically lit approximately 5 minutes later.

4. Close the SD memory card cover.

Remove a microSD memory card
When removing a microSD memory card, reverse the procedure.

• To remove the microSD memory card, hold down the SD ON/OFF button for about 2 seconds. When the flashing SD MOUNT indicator goes out, you can remove the microSD memory card.

IMPORTANT:

• Before turning off the camera power switch, make sure that the SD MOUNT indicator is turned off. If you turn off the camera power switch while the SD MOUNT indicator is lit or flashing, the recorded data may be corrupted or damaged.

Note:

• Refer to the Operating Instructions on our product information website for further information about the microSD memory card settings.
• When using a microSD memory card, format it using this product. Recorded data on the microSD memory card will be deleted when formatted.
• If an unformatted microSD memory card or a microSD memory card formatted with other devices is used, this product may not work properly or performance deterioration may be caused. Refer to the Operating Instructions on our product information website for how to for-mat a microSD memory card.

Troubleshooting

Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below.

• Are the PoE device (IEEE802.3af compliant) and the RJ45 Network connector connected using an Ethernet cable?
  Check whether the connection is appropriately established.

• Depending on the PoE device, the power supply will stop when the demanded power exceeds its total power limit for all PoE ports.

Refer to the operating instructions of the PoE device in use.

| Installation Guide
When using DC power supply

• Is the power cord plug (accessory) firmly inserted into the power supply terminal (12 V DC) of the camera? Confirm the power plug is firmly connected.
• Is the AC adaptor in use compliant with the Specifications?
  Check the Specifications regarding AC adaptor.

The camera does not move to the preset positions accurately.|

• When the preset positions become inaccurate during use, it is possible to correct the positions by executing the position refresh function.
  In addition, when “Position refresh” is set for the created schedule, the camera position will be corrected periodically. In some situations, reconfigure the preset positions.

| Operating Instructions
When the camera is panning/tilting, the camera stops panning/ tilting and mechanical noise comes from the camera.|

• The camera position may have become inaccurate. Carry out the refresh position function from the [Default reset] tab of the “Maintenance” page of the setup menu.

| Operating Instructions
The camera starts panning unpredictably.|

• This may be caused by noise.

Check the exogenous noise level around the camera.

| 6
When using an optional inner cover, upper side of images are hidden (become black) when the tilt angle of the camera is almost level.| The inner cover is designed to be used to reduce the visibility of the i-PRO white body silhouette through the dome cover that is provided with the mount bracket.

• This is not malfunction. This is caused by the shape of the inner cover.
  Also, if the setting of “Maximum gain” is too large, the image will become white depending on the subject.

| −
Symptom| Cause/solution| Reference pages
---|---|---

The LINK indicator does not light in orange even when the Ethernet cable is connected to the camera.

|

• Is the Ethernet cable connected appropriately? Connect the Ethernet cable appropriately.

• Is the hub or router connected to the camera operating appropriately?
  Check if the hub or router in use is operating appropriately.

• Is the Ethernet cable connected to the camera broken? Replace the cable with another one.

| 9
The SD MOUNT

indicator does not light even when a microSD memory card is installed.

| This indicator lights up green when the microSD memory card is recognized correctly and ready for use.

• Has the inserted microSD memory card been formatted on a PC?

Use a microSD memory card formatted on the camera. Or install the software to format the microSD memory card on the PC.

Refer to our technical information website for further information about the supported software.

• Is the inserted microSD memory card faulty?

Replace the card with a normal one.

| 13
Audio input contains noise.|

• Check the following.
• Grounding of the camera, a switching hub or peripheral devices are not done.
• The camera is used near an electrical power line.
• The camera is used near a device which produces strong magnetic field or radio waves (such as near a TV/radio antenna, a motor of an air conditioning system, a transformer, etc.)

When audio input still contains noise even after checking the above possibilities, use a powered microphone or connect audio output with low output impedance.

| Installation Guide
The focus can not be automatically adjusted.|

• In the following locations or with the following subjects, the focus may not be able to be automatically adjusted. In this case, manually adjust the focus from the setup menu.
• When the subject moves a lot
• When there are large changes to the lighting intensity
• When the light level is low
• When the subject or location is extremely bright or reflective
• When viewing through windows
• When the dome cover is in a locations where it can easily become dirty
• Locations where there is not much contrast such as a white wall
• When there is harsh flickering

| Operating Instructions

Power source*1:| 12 V DC

PoE (IEEE802.3af compliant)

---|---
Power consumption*1:| 12 V DC:            970 mA/Approx. 11.6 W

PoE 48 V DC: 270 mA/Approx. 12.95 W (Class 0 device)

Operating environment Ambient operating temperature:

**** Ambient operating humidity:

| –10 °C to +50 °C {14 °F to 122 °F}

(Power On range: 0 °C to 50 °C {32 °F to 122 °F}) 10 % to 90 % (no condensation)

Storage environment

Storage temperature: Storage humidity:

| –30 °C to +60 °C {–22 °F to +140 °F}

10 % to 95 % (no condensation)

EXT I/O terminal:| ALARM IN1

(Alarm input 1/ Black & white input/ Auto time adjustment input) (x1)

ALARM IN2 (Alarm input 2/ ALARM OUT) (x1) ALARM IN3 (Alarm input 3/ AUX OUT) (x1)

Audio input:

For microphone input:

For line input:

| ø3.5 mm stereo mini jack

Recommended applicable microphone: Plug-in power type (Sensitivity of microphone: –51 dB to –38 dB (0 dB=1 V/Pa, 1 kHz)) Input impedance: Approx. 2 kΩ (unbalanced)

Supply voltage: 2.5 V ±0.5 V

Input level: Approx. –10 dBV

Audio output*2:| ø3.5 mm stereo mini jack (Audio output is monaural.) Output impedance: Approx. 600 Ω (unbalanced)

Output level: –20 dBV

Dimensions:| Maximum diameter: ø117 mm × 155 mm (H)

{ø4-19/32 inches × 6-3/32 inches (H)} Dome radius: 52 mm {2-1/16 inches}

Mass:| Approx. 1.2 kg {2.65 lbs}

(Including camera mount bracket, decorative cover: Approx. 200 g {0.44 lbs})

Finish:| Main body:     Aluminum die cast/PC+ABS resin, i-PRO white

Dome cover: Acrylic resin, Clear

1. Refer to our technical information website for further information about Power source and Power consumption information.
2. The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on our product information website for descriptions of how to switch the output.

Camera

Approx. 5.1 megapixels

61301Z2 61301Z1

Approx. 2.1 megapixels

Scanning area:| 61501Z1

5.12 mm (H) × 3.84 mm (V) {3/16 inches (H) × 5/32 inches (V)}

61301Z2 61301Z1

5.57 mm (H) × 3.13 mm (V) {7/32 inches (H) × 1/8 inches (V)}

Scanning system:| Progressive
Minimum illumination:| 61501Z1

Color: 0.08 lx {0.00743 footcandle}

(30IRE, F1.6, Maximum shutter: Off (1/30 s), AGC: 11)*

0.11 lx {0.01022 footcandle}

(50IRE, F1.6, Maximum shutter: Off (1/30 s), AGC: 11)

0.007 lx {0.00065 footcandle}

(50IRE, F1.6, Maximum shutter: max. 16/30 s, AGC: 11)* BW: 0.06 lx {0.00557 footcandle}

(50IRE, F1.6, Maximum shutter: Off (1/30 s), AGC: 11)

0.004 lx {0.00037 footcandle}

(50IRE, F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*

61301Z2 61301Z1

Color: 0.011 lx {0.00102 footcandle}

(30IRE, F1.6, Maximum shutter: Off (1/30 s), AGC: 11)*

0.015 lx {0.00139 footcandle}

(50IRE, F1.6, Maximum shutter: Off (1/30 s), AGC: 11)

0.001 lx {0.00009 footcandle}

(50IRE, F1.6, Maximum shutter: max. 16/30 s, AGC: 11)* BW: 0.006 lx {0.00056 footcandle}

(50IRE, F1.6, Maximum shutter: Off (1/30 s), AGC: 11) 0.0004 lx {0.00004 footcandle}

(50IRE, F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*

• Converted value

Intelligent Auto:| On/Off
Super Dynamic*1:| On/Off

The level can be set in the range of 0 to 31.

Dynamic range:| 61501Z1

Max. 132 dB (Super Dynamic: On, Level: 31, 15 fps*2)

61301Z2 61301Z1

Max. 144 dB (Super Dynamic: On, Level: 31)

Maximum gain:| The level can be set in the range of 0 to 11.
Adaptive black stretch:| The level can be set in the range of 0 to 255.
Back light compensation (BLC)/ High light compensation (HLC):| BLC/ HLC/ Off

The level can be set in the range of 0 to 31. (only when Super Dynamic/ Intelligent Auto: Off)

Fog compensation:| On/Off

The level can be set in the range of 0 to 8.

(only when Intelligent Auto / Auto contrast adjust: Off)

Light control mode setting:| Outdoor scene/ Indoor scene (50 Hz)/ Indoor scene (60 Hz)/

Fix shutter

Shutter speed:| 61501Z1 [30 fps mode]

1/30 Fix, 3/120 Fix, 2/100 Fix, 2/120 Fix, 1/100 Fix, 1/120 Fix,

1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix

[25 fps mode]

1/25 Fix, 3/100 Fix, 2/100 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix,

1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix

61301Z2 61301Z1

[60 fps mode]

1/60 Fix, 1/100 Fix, 1/120 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix,

1/2000 Fix, 1/4000 Fix, 1/10000 Fix

[30 fps/ 15 fps mode]

1/30 Fix, 3/120 Fix, 2/100 Fix, 2/120 Fix, 1/100 Fix, 1/120 Fix,

1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix

[50 fps mode]

1/50 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix,

1/4000 Fix, 1/10000 Fix

[25 fps/ 12.5 fps mode]

1/25 Fix, 3/100 Fix, 2/100 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix,

1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix

Maximum shutter:| 61501Z1 [30 fps mode]

Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s, Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s,

Max. 2/100 s, Max. 3/120 s, Max. 1/30 s, Max. 2/30 s, Max. 4/30 s,

Max. 6/30 s, Max. 10/30 s, Max. 16/30 s

[25 fps mode]

Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,

Max. 1/250 s, Max. 1/100 s, Max. 2/100 s, Max. 3/100 s, Max. 1/25 s, Max. 2/25 s, Max. 4/25 s, Max. 6/25 s, Max. 10/25 s, Max. 16/25 s

| 61301Z2 61301Z1 [60 fps mode]

Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,

Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s, Max. 1/30 s, Max. 2/30 s, Max. 4/30 s, Max. 6/30 s, Max. 10/30 s, Max. 16/30 s [30 fps/ 15 fps mode]

Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s, Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s,

Max. 2/100 s, Max. 3/120 s, Max. 1/30 s, Max. 2/30 s, Max. 4/30 s,

Max. 6/30 s, Max. 10/30 s, Max. 16/30 s

[50 fps mode]

Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,

Max. 1/250 s, Max. 1/100 s, Max. 2/100 s, Max. 1/25 s, Max. 2/25 s,

Max. 4/25 s, Max. 6/25 s, Max. 10/25 s, Max. 16/25 s

[25 fps/ 12.5 fps mode]

Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,

Max. 1/250 s, Max. 1/100 s, Max. 2/100 s, Max. 3/100 s, Max. 1/25 s, Max. 2/25 s, Max. 4/25 s, Max. 6/25 s, Max. 10/25 s, Max. 16/25 s

Color/BW:| Off/ On/ Auto1/ Auto2/ Auto3(SCC)
White balance:| ATW1/ ATW2/ AWC
Digital noise reduction:| The level can be set in the range of 0 to 255.
Stabilizer:| On/Off
Privacy zone:| On/Off

Up to 32 zones available

VIQS:| On/Off

Up to 8 zones available

Camera title on screen:| On/Off

Up to 40 characters, Up to 2 lines (alphanumeric characters, marks)

Video Motion Detection (VMD):| On/Off

4 areas available

Scene Change Detection (SCD):| On/Off

1 area available

Audio Detection:| On/Off
AI Sound classification: