i-PRO WV-QDC504C Dome Cover Installation Guide
- June 10, 2024
- i-PRO
Table of Contents
WV-QDC504C Dome Cover
Installation Guide
Installation Guide
Included Installation Instructions
Dome Cover
Model No. WV-QDC504C
WV-CW7CN, WV-CW7SN , WV-CW7S
WV-QDC504C Dome Cover
- Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
- The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
- Read also the installation guide of the camera to be used.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage
resulting from failures arising out of improper installation or operation
inconsistent with this documentation.
“<Control No.: C**>” used in these documents should be used to search for
information on our technical information
website (https://i-pro.com/global/en/surveillance/training-support/support
/technical-information) and will guide you to the right information.
https://i-pro.com/global/en/surveillance/training-support/support
/technical-information
Caution:**
• Before attempting to connect or operate this product, please read these
instructions carefully.
Precaution
Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
Refer installation work or dome cover replacement to the dealer.
Installation work requires technique and experiences.
Failure to observe this may cause fire, electric shock, injury, or damage to
the product.
Be sure to consult the dealer.
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
When using this product, also read the “Precautions” described in the
operating instructions for the camera to be attached.
Preface
This product is the clear type dome cover.
This product is the smoke type dome cover (approx. 45 % of transmittance).
Specifications
| Ambient operating temperature: | –50 °C to +60 °C {–58 °F to 140 °F} |
|---|---|
| Dimensions: | ø115 mm × 60 mm (H) |
{ø4-17/32 inches × 2-3/8 inches (H)}
(Dome diameter 42 mm {1-21/32 inches})
Mass:| Approx. 74 g {0.16 lbs}
Finish:| PC resin Clear
Precaution for installation
„Screw tightening.
Do not use an impact driver. Use of an impact driver may damage the screws or
cause tightening excessively.
„About Clear Sight coating
-
Due to effectiveness of the Clear Sight coating, drops are likely to be accumulated right under the camera and it may cause a partial distortion of the video.
-
When cleaning the dome cover, hose or spray fresh water that is not containing lubricant agent or silicon substances and wash away adherents such as grain of sand. If dirt is hard to remove, use a sponge soaked into the fresh water mentioned above and wipe off.
-
Do not wipe the cover with a dry cloth. (Using dry cloth may spread oil constituent adhered to the surface, and it may result in damaging the Clear Sight coating.)
-
If dirt cannot be wiped off with a damp cloth, use a neutral detergent and sufficiently rinse off the detergent.
-
Do not use organic solvent such as benzine and thinner.
-
Before using a spray, abandon a few sprays to eliminate impurities.
-
The mark of light-shielding parts left inside the dome or dirt on the dorm cover may influence the reflection of infrared rays. Therefore, remove those marks and dirt using cleaning paper.
-
Improper cleaning of the dome cover may cause the Clear Sight coating to become less effective. In this case, in order to have effective Clear Sight coating, a new dome cover must be purchased to replace the existing dome cover. Consult with your dealer or construction contractor.
„ The procedure for installing this unit to the network camera varies depending on the model used. Install according to the following compatible models.
Installation Type1
Be careful to the following when replacing the dome cover:
– The waterproof rubber (Sealing Packing)may come off simultaneously. Attach
the waterproof rubber to the original position before attaching this product.
– It is recommended to check whether the waterproof rubber is deteriorated.
When it has deteriorated, the waterproof performance will decrease, so
consider repairing it.
When replacing the dome cover, remove the protection film covering outside
this product. After replacement, attach the protection film back to the
outside this product. (Handle the new dome cover with care not to scratch
inside and outside.)
Installation Type2
Be
careful to the following when replacing the dome cover:
– The waterproof rubber (Sealing Packing) may come off simultaneously. Attach
the waterproof rubber to the original position before attaching this product.
– It is recommended to check whether the waterproof rubber is deteriorated.
When it has deteriorated, the waterproof performance will decrease, so
consider repairing it.
When replacing the dome cover, remove the protection film covering outside
this product. After replacement, attach the protection film back to the
outside this product. (Handle the new dome cover with care not to scratch
inside and outside.)
i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2023
C0223-0
PGQP3698ZA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>