i-PRO WV-QDC502G Dome Cover Instruction Manual

i-PRO WV-QDC502G Dome Cover

Product Information

• Product Name: Smoke Type Dome Cover
• Model Number: WV-QDC502G
• Transmittance: Approx. 45%
• Ambient Operating Temperature: Not Specified
• Dimensions: Not Specified
• Mass: Not Specified
• Finish: Not Specified

Product Usage Instructions

1. Before installing the product, read the operating instructions and the precautions carefully.
2. Ensure that the decorative cover is rotated by approximately 10 degrees counterclockwise in topneath view.
3. Remove the dome cover holding plate (4 pcs.).
4. Remove the decorative cover.
5. Remove the old dome cover and attach the new one (smoke). Remove the protection film covering outside the new dome cover. Keep the removed protection film until using it upon installation. (Handle the new dome cover with care not to scratch inside and outside.)
6. Tighten the mounting screws (accessory) to attach the dome cover holding plate (accessory). Ensure that the screws and bolts are tightened to the specified torque (a bit length of 75 mm{2-15/16 inches} or more).
7. Attach the decorative cover.
8. Rotate the decorative cover by approximately 10 degrees clockwise in topneath view. Attach the protection film removed in Step 5 to the surface of the dome cover again. After completing the installation, remove the protection film.
9. Install the camera by following the instructions in the Installation Guide of the camera.

Standard accessories

• Operating Instructions (this document) – 1 pc.
• Dome cover holding plate – 4 pcs.
• Mounting screw – 10 pcs. (of them, 2 for spare)

Precautions

• Do not use this product except with suitable cameras. Failure to observe this may cause a drop resulting in injury. Refer installation work to the dealer. Installation work requires technique and experience. Failure to follow this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.
• When using this product, also read the Precautions described in the operating instructions for the camera to be attached.

Operating Instructions

• Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
• Read also the installation guide of the camera to be used.

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

“<Control No.: C****>” used in these documents should be used to search for information
on our technical information website (https://i-pro.com/global/en/surveillance/trainingsupport/support/technical- information) and will guide you to the right information.

i-PRO Co., Ltd.
https://www.i-pro.com/

Caution

Before attempting to connect or operate this product, please read these instructions carefully.

Precaution

• Do not use this product except with suitable cameras.
  Failure to observe this may cause a drop resulting in injury.

• Refer installation work to the dealer.
  Installation work requires technique and experience.
  Failure to observe this may cause fire, electric shock, injury, or damage to the product.
  Be sure to consult the dealer.

• The screws and bolts must be tightened to the specified torque.
  Failure to observe this may cause a drop resulting in injury or accidents.

When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.

Preface

• This product is the smoke-type dome cover (approx. 45 % of transmittance).
• The latest information about the supported cameras .

Specifications

• Ambient operating temperature: –50 °C to +60 °C {–58 °F to 140 °F}
• Dimensions: ø131 mm × 89 mm (H) {ø5-5/32 inches × 3-1/2 inches (H)}
• Mass: Approx.110g {0.24lbs}
• Finish: PC resin, Smoke

Standard accessories

Operating Instructions (this document)……………………………………………………………………………….1 pc.
Dome cover holding plate………………………………………………………………………………………………4 pcs.
Mounting screw………………………………………………………………………………………………………….10 pcs.
(of them, 2 for spare)

Installation

Step 1
Rotate the decorative cover by approximately 10 degrees counterclockwise in topneath view.

Step 2

Remove the decorative cover.

Step 3

Remove the dome cover holding plate (4 pcs.).

Caution

• Use the screwdriver (locally procured) with a bit length of 75 mm {2-15/16 inches} or more.
• Dispose of the removed dome cover holding plates (4 pcs.) and mounting screws (8 pcs.).

Step 4

Remove the dome cover.

Step 5

Attach the dome cover (smoke). Remove the protection film covering outside the new dome cover. Keep the removed protection film until using it upon installation. (Handle the new dome cover with care not to scratch inside and outside.)

Step 6

Tighten the mounting screws (accessory) to attach the dome cover holding plate (accessory).

Caution

• Use the screwdriver (locally procured) with a bit length of 75 mm {2-15/16 inches} or more.

• Tighten the mounting screws from ① to ④ in order in the illustration.

• 0.3 N·m {0.22 lbf·ft}

Step 7

Attach the decorative cover.

Step 8

• Rotate the decorative cover by approximately 10 degrees clockwise in topneathview.
• Attach the protection film removed in step 5 to the surface of the dome cover again.
• After completing the installation, remove the protection film.

Step 9

Install the camera by following the instructions in the Installation Guide of the camera.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>