SUREFIRE X300-A-Series Illumination Tool Handgun Light Lever Latch Mount Instruction Manual

SUREFIRE X300-A-Series Illumination Tool Handgun Light Lever Latch Mount

Instruction Manual

| X300T-A| X300U-A
---|---|---
OUTPUT| 650 lumens| 1,000 lumens
RUNTIME| 1.5 hours| 1.25 hours
PEAK BEAM INTENSITY| 66,000 candela| 11,300 candela
DISTANCE| 514 meters| 213 meters
CONSTRUCTION| Aluminum
FINISH| Hard Anodized (MIL-A-8625 Type III, Class 2)
WEIGHT (w/batteries)| 4.0 oz (113 g)
LENGTH| 3.76 in (9.55 cm)
BEZEL DIAMETER| 1.125 in (2.9 cm)
BATTERIES| Two 123A lithium (incl.)
SWITCHING| Ambidextrous push/toggle
LIQUID INGRESS PROTECTION| IPX7, Submersion up to one meter for 30 minutes

BEFORE INITIAL USE, REMOVE BATTERY INSULATOR

KIT CONTENTS:

• X300 WeaponLight
• Battery Cover
• Battery Cover Retaining Pin
• Universal Lever Latch (marked “U,” installed)
• Picatinny Lever Latch (marked “P”)
• Spring (installed)
• Rail Latch Lock
• Universal Rail Latch (marked “U”)
• Picatinny Rail Latch (marked “P”)
• Lock Actuator
• Lock Actuator Screw
• 5/64-inch Hex Wrench
• One Tube Loctite 242
• Two 123A Batteries

BATTERY INSTALLATION / REPLACEMENT

1. Attach Battery Cover (Figure 1).
   

2. Insert two 123A Batteries with terminals oriented as shown in the engraved schematic on X300 body (Figure 1).

3. Close Battery Cover until compartment latch clicks and locks cover in

4. To replace batteries, depress latch to open Battery

5. Install fresh batteries and re-secure Battery

6. (OPTIONAL) Using pliers, insert battery cover Retaining Pin through both holes in latch bracket, until pin locks in place and latch cannot be released (Figure 2).

CAUTION: Mixing a depleted battery with a new battery can cause damage to the weaponlight. Always use two fresh batter- ies when replacing old ones.

MOUNTING X300 TURBO TO WEAPON

point using a spring-assisted latch that can be actuated by hand and is done without tools. A Picatinny Lever Latch is included to fit host weapon accessory rails with Picatinny cross slots.
X300 A-series weaponlights also include the Rail-Lock system that provides a more robust attachment platform that is also easily actuated by hand but does require a hex key to rigidly attach to

a weapon accessory rail. A Universal and Picatinny Rail-Lock is included to fit host weapon accessory rails with Universal and Picatinny cross slots.

INSTALLATION & REMOVAL (LEVER LATCH SYSTEM)

1. Align Rail Guides with grooves of Universal accessory

2. Pull down on Lever Latch tabs and slide X300 onto the accessory rail of host weapon until Lever Latch clicks and locks securely in place (Figure 3).
   

3. To remove, press down on Lever Latch tabs and slide X300 forward off rail (Figure 3).

INSTALLATION & REMOVAL (RAIL-LOCK SYSTEM)

1. Pull Rail Latch Lock tabs rearward to release Rail Latch. Slide Rail Latch to the open position–Rail Latch is not designed to come all the way out (Figure 4).
2. Slide X300 onto host weapon accessory rail and align rail latch with accessory rail slot on host Press in Rail Latch until it locks in place (Figure 5).
3. Insert 5/64-inch Hex Wrench into slot and tighten Lock Actuator
4. To remove, loosen Lock Actuator Screw with Hex Wrench, pull back Rail Latch Lock tabs, slide Rail Latch to the open position and remove weaponlight from host weapon accessory

LEVER LATCH REMOVAL & INSTALLATION

1. Use the 5/64-inch Hex Wrench to remove Rail Guides by unscrewing the Hex Screws (Figure 6).
   

2. Lift up and remove Lever Latch from hinge Capture Lever Latch Spring and retain. Retain and store replaced Lever Latch future use (Figure 7).

3. Hook Lever Latch onto X300 Hinge Pin so the SureFire logo is Place Spring under Lever Latch so it nests in round slot on the underside of Lever Latch and on the top of the X300 body (Figure 7).

4. Press down and hold Lever Insert screws into Rail Guides. Align left Rail Guide with holes on left side of body and tighten screws using an alternating pattern until all three screws
   stop turning. Repeat for right side Rail Guide. Tighten screws to 4 in-lbs, or use the 5/64” hex wrench and tighten screws with light pressure (do not over- tighten).

5. While holding down Lever Latch tabs, slide X300 onto host weapon accessory rail until Lever Latch’s crossbar mates with accessory rail cross

6. (OPTIONAL) Sparingly apply Loctite 242 to each Rail Guide Screw to further prevent screws from loosening from live fire

RAIL-LOCK® INSTALLATION

1. Using the 5/64-inch Hex Wrench, remove both Rail Guides (Figure 6).

2. Remove Lever Latch and Store both for future use.

3. Insert Lock Actuator into slot on Rail Latch Insert Lock Actuator Screw into screw hole and turn clockwise until it engages Lock Actuator (Figure 8).

4. Place hooked end of Rail Latch Lock onto Hinge Pin and insert Rail Latch Lock (actuator facing down) so it fits into slot on top of Lock Actuator Screw may need to be loosened or tightened for screw head to align with screw head slot (Figure 9).

5. Select appropriate Rail

6. Lift front edge of Rail Latch Connect slotted side of Rail Latch to front edge of Rail Latch Lock (Figure 8).
   

7. Lower Rail Latch Lock and attached Rail Latch, fitting both into their designated slots in

8. Insert screws into Rail Guides. Align left Rail Guide with holes on left side of body and tighten screws using an alternating pattern until all three screws stop Repeat for right side Rail Guide. Tighten screws to 4 in-lbs, or use supplied 5/64” hex wrench and tighten screws with light pressure (do not over- tighten). One Rail Guide has a notch, which fit over the Rail Latch (Figure 6).

9. (OPTIONAL) Sparingly apply Loctite 242 to each Rail Guide Screw to further prevent screws from loosening from live fire

LIGHT OPERATION

For momentary-on light operation, press and hold either the right or left side of tailcap toggle switch; release to turn light off (Figure 10). For constant-on operation, rotate tailcap toggle switch up or down; rotate in the opposite direction to turn light off (Figure 10).

Note: Remote switches are available for SureFire X-Series WeaponLights. Visit www.surefire.com/parts-accessories/ switches.html

Read More About This Manual & Download PDF

References

• SureFire
• SureFire | Tactical Illumination Tools & Suppressors for Professionals
• Parts & Accessories | SureFire

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>