IKEA 23244 Wall Mounted Extractor Hood Instruction Manual

Safety Information

Before first use
Your safety and that of others is paramount.
Remove cardboard protection pieces, protective film and adhesive labels from accessories. Check the appliance for any transport damage.
To avoid any damage do not place any weights on the appliance. Do not expose the appliance to atmospheric agents. This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
** This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the attention symbol and the following terms:
DANGER: indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING:** Indicates a hazardous situation which, if not avoided, could cause serious injury.
All safety warnings give specific details of the potential danger/ warning present and indicate how to reduce risk of injury, damage and electric shock resulting from improper use of the appliance. Carefully observe the following instructions.

Precautions and general recommendations

• The electrical installation and the electrical connection must be carried out by a qualified technician according to the manufacturer’s instructions and in compliance with the local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the user manual.
• The appliance must be disconnected from the power supply before carrying out any installation work.

WARNING: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

• Earthing of the appliance is compulsory. (Not possible for class II hoods identified by the symbol on the dataplate).

• Do not pull the power supply cable in order to unplug the appliance.

• The electrical components must not be accessible to the user after installation.

• Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
  shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• All other maintenance services must be carried out by a specialised technician.

• When drilling through the wall pay attention not to damage electric connections and/or pipes.

• Air vents must always discharge to the outside.

• The manufacturer rejects all responsibilities for any damage caused by improper use or wrong settings.

• Appropriate maintenance and cleaning ensure the good working order and the best performance of the appliance. Regularly clean all stubborn surface dirt to avoid grease build up. Remove and clean or change the filter regularly. This must be completed in accordance with the “Cleaning and maintenance” instructions provided.

• Never flame cook food (flambé) under the appliance. Using free flames might cause fire.

• Failure to observe the instructions for cleaning the hood and replacing the filters may result in a fire.

• Exhaust air must not be vented through a flue used for removal of fumes produced by gas combustion appliances or other combustible materials, but must have a separate outlet. All national regulations governing extraction of fumes must be observed.

• There shall be adequate ventilation if the hood is being used at the same time as other appliances using gas or other combustible materials. The negative pressure of the room must not exceed 4 Pa (4x 10-5 bars). For this reason ensure that the room is well ventilated. In case of doubts, please consult an autorized service assitance center or similar qualified person.

• Do not leave frying pans unattended when frying, as the frying oil may catch fire.

• Before touching the light bulbs, ensure that they are cold.

• Do not use or leave the hood without the light bulb correctly fitted, as this may cause electric shock.

• The hood is not a work surface, therefore do not place any objects on top of it or overload it.

• During all installation and maintenance operations wear appropriate working gloves.

• This appliance is not suitable for outdoor use.

WARNING: when the hob is in use, accessible parts of the hood may become hot.
Installation and connection
In the event of problems, contact the Authorized Service Centre. To prevent any damage, only remove the appliance from its packaging at the time of installation.

Preparing for installation
WARNING: this is a heavy product; the hood should only be lifted and installed by two or more people.
The minimum distance between the hob and the bottom part of the hood must not be less than 65 cm for burning gas or other fuels and 50cm for electric cookers.
Before installation also check the minimum distances stated in the manual of the cooker.
If the installation instructions for the cooker specify a greater distance between cooker and hood, this distance must be observed.
Electrical connection
Make sure the power voltage specified on the appliance rating plate is the same as the mains voltage.
This information can be found on the inside of the hood, under the grease filter. Power cable replacement (type H05 VV-F) must be carried out by a qualified electrician. Contact an authorized service centre.
If the hood is fitted with an electric plug, connect the plug to a socket complying with current regulations, located in an accessible place.
WARNING: if no plug is fitted (direct wiring to the mains), or if the socket is not located in an accessible place, a qualified electrician should install a standardised double pole power switch that will enable complete isolation from the mains in case of category III overvoltage conditions, in accordance with wiring rules.

Use

The hood has been designed to be installed and used either as a “Extraction installation”, or as a “Recirculation installation”.
Extraction installation (see symbol in installation booklet)
Cooking steam is sucked and channelled outside the house through a discharge duct (not supplied), fitted to the hood steam outlet.
Ensure that the discharge duct is correctly fitted to the air outlet, unit using an appropriate connection system.
Important: If already installed, remove the charcoal filter/s.
Recirculation installation
(see symbol in installation booklet)
The air is filtered through one or more the charcoal filters, and then resent into room.

Important: Ensure appropriate air circulation around the hood.
Important: If the hood is supplied without charcoal filters, these must be fitted before the hood can be used. Filters are available in IKEA shops.
The hood should be installed away from particularly dirty areas, windows, doors and heat sources.
The accessories for wall fixing are not included because walls made of different materials require different types of fixing accessories. Use fixing systems suitable for the walls of your home and the weight of the appliance. For more details, contact a specialized dealer.
Keep this booklet for future consultation.

Product description

1. Chimney.
2. Control Panel.
3. Light.
4. Grease filter.

Control panel

A Motor ON/OFF toggle switch
B Suction (power) speed selector knob
Low suction (power) speed
Medium suction (power) speed
High suction (power) speed
Maximun suction (power) speed
NB: the hood remains at the same speed when switched ON/OFF using the toggle switch
C Light ON/OFF toggle switch

Cleaning and maintenance

WARNING:
– Never use steam cleaning equipment.
– Disconnect the hood from the electric power supply.
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean immediately with a damp
cloth.

• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off with a dry cloth.

IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the surface.

• Use detergents specifically designed for cleaning the appliance and follow the manufacturer instructions.

IMPORTANT: clean the grease filters at least monthly to remove any oil or grease residuals.
To clean the grease filter
The metal grease filter has an unlimited life and must be washed once a month by hand or dishwasher at low temperature and with a short cycle. With cleaning in a dishwasher the grease filter may become dull; this does not effect its filtering capacity.

Grease filter maintenance:

1. Disconnect the hood from the electric power supply.
2. Remove the grease filters: pull the spring release handle downwards, then remove the filter.
3. After cleaning the grease filter, remount in reverse order ensuring the entire extraction surface is covered.

Charcoal filter maintenance (if the hood is installed in recirculation mode)

1. Pull out the plug or disconnect the powsupply.
2. Remove the grease filter
3. If the carbon filters are already fitted (two filters that cover the protective grilles for the motor impeller) and have to be replaced, turn the central handle anti-clockwise to unlock them.
4. Open the two filter shells
5. Pull out the two circular mats
6. Proceed in reverse order to fit the new filters.
7. Refit the grease filters.

Unlike traditional charcoal filters, this charcoal filter can be washed and reactivated.
With normal hood use, the filter should be cleaned once a month. The best way to clean the filter is in a dishwasher at the highest temperature possible, using a normal dishwasher detergent. To avoid particles of food or dirt settling on the filter during washing and giving rise to unpleasant smells, it is advisable to wash the fi lter on its own. After washing, dry the filter in the oven at 100°C for 10 minutes to reactivate it. The filter will retain its odourabsorbing capacity for three years, after which it will have to be replaced.

Lamp maintenance
The hood is equipped with a lighting system based on LED technology.
The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy.
For replacement, contact the Authorized Service Centre.

What to do if …

presence of mains electrical power.
Turn off the appliance and restart it to see if the faults persists.
The appliance is not connected to the
electrical supply| Check if the appliance is connected to the electrical supply.
Turn off the appliance and restart it to see if the faults persists.
The hood’s suction level is not enough| The suction speed is too low| Check the suction speed and adjust as necessary.
The grease filters are| Check that the filters are clean
If not, clean the filters in the dishwasher.
dirty 4
The anti-odors filters are dirty| Check that the anti-odour filters are properly washed as recommended
The air vents are obstructed| Check the air vents for any obstructions and remove as necessary.
The light does not work| The LED is broken 3| For replacement, contact the Authorized Service Centre.

Before contacting the Authorized Service Centre:
Switch the appliance on again to see if the problem has disappeared. If not, switch it off again and repeat the operation after an hour. If your appliance still does not work properly after carrying out the checks listed in the troubleshooting guide and switching the appliance on again, contact the Authorized Service Centre, clearly explaining the problem and specifying:

• the type of fault;
• the model;
• the type and serial number of the appliance (given on the rating plate);
• the Service number (the number after the word SERVICE on the rating plate inside the appliance).

Technical data

Additional Product Information compliant to commission regulation (EU) No 66/2014
Model identifier| | MATTRADMON 20443209
Annual Energy Consumption| kWh/a| 43.
Time increase factor| | 0.9
Fluid Dynamic Efficiency| %| 31,6
Energy Efficiency Index| | 523
Measured air flow rate at best efficiency point| m3/h| 314,0
Measured air pressure at best efficiency point| Pa| 416,0
Maximum air flow| m3/h| 550
Measured electric power input at best efficiency point| W| 115,0
Nominal power of the lighting system| W| 7
Average illumination of the lighting system on the cooking surface| lux| 203,0
Power consumption in standby mode| W| NA
Power consumption off mode| W| NA
A-waighted Sound Power Emission at maximum speed| d8(A)| 65

The technical information is situated in the rating plate on the internal side of the appliance.

Environmental concerns

Disposal of packing
The packing material is 100% recyclable and is marked with the recycle symbol . The various parts of the packing must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

Scrapping the product
– This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
– By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste butmust be taken to an appropriate ollection centre for the recycling of electrical and electronic equipment.

Scrapping of household appliances

• This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut off the power supply cable.
• For further information on the treatment, recovery and recycling of household electrical appliances, contact your competent local authority, the collection service for household waste or the store where you purchased the appliance.

Energy saving tips

• Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished.
• Increase the speed only in case of large amount of smoke and vapour and use boost speed(s) only in extreme situations.
• Replace the charcoal filter(s) when necessary to maintain a good odour reduction efficiency.
• Clean the grease filter(s) when necessary to maintain a good grease filter efficiency.
• Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.

Declaration of conformity
This appliance has been designed, manufactured and marketed in compliance with:
– safety objectives of the “Low Voltage” Directive 2014/35/EU;
– the eco design requirements of european regulations n. 65/2014, and n. 66/2014 in conformity to the european standard en 61591 ;
– the protection requirements of Directive
“EMC” 2014/30/EU.
Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system.

IKEA GUARANTEE

How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years – two (2) years if the appliance is named LAGAN or TILLREDA – from the original date of purchase of your appliance at IKEA or from the installation date with maximum limit of three months from the purchase date.
The original sales receipt, is required as proof of purchase.
If service work is carried out under guarantee, this will not extend the guarantee period for the appliance.
Once a warranted product has been replaced, the replaced product warranty will be valid for the balance period from date of original purchase invoice
Who will execute the service?
IKEA service provider will provide the service through its own service operations or authorized service partner network.

What does this guarantee cover?

• The guarantee covers faults of the appliance, which have been caused by faulty construction or material faults from the date of purchase from IKEA or from the installation date with maximum limit of three months from the purchase date.
• This guarantee applies to domestic use only.
• The exceptions are specified under the headline “What is not covered under this guarantee?” Within the guarantee period,
• The costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that the appliance is accessible for repair without special expenditure. On these conditions the respective local regulations are applicable.
• Replaced parts become the property of IKEA.
• In case of non-repairable product, the retail value of the replacement will not exceed the purchase price that was paid by the customer

What will IKEA do to correct the problem?

• IKEA appointed Service Provider will examine the product and decide, at its sole discretion, if it is covered under this guarantee. If considered covered, IKEA Service Provider or its authorized service partner through its own service operations, will then, at its sole discretion, either repair the defective product or replace it with the same or a comparable product.

What is not covered under this guarantee?

• Normal wear and tear.

• Deliberate or negligent damage, damage caused by failure to observe operating instructions, incorrect installation or by connection to the wrong voltage, damage caused by chemical or electrochemical reaction, rust, corrosion or water damage including but not limited to damage caused by excessive lime in the water supply,
  damage caused by abnormal environmental conditions.

• Consumable parts including batteries and lamps.

• Non-functional and decorative parts which do not affect normal use of the appliance, including any scratches and possible colour differences.

• Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems or soap drawers.

• Damage to the following parts: ceramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults.

• Cases where no fault could be found during a technician’s visit.

• Repairs not carried out by our appointed service providers and/or an authorized service contractual partner or where non- original parts have been used.

• Repairs caused by installation which is faulty or not according to specification

• The use of the appliance in a non-domestic environment i.e. professional use.

• Transportation damages. If a customer transports the product to his home or another address, IKEA is not liable for any damage that may occur during transport. However, if IKEA delivers the product to the customer’s delivery address, then damage to the product that occurs during this delivery will be covered by IKEA.

• Damage resulting from power outage, power surges or dips, fluctuating voltage or improper voltage All workout parts are not covered by the guarantee e.g.: filters and cleanliness.

• Cost for carrying out the initial installation of the IKEA appliance. However, if an IKEA appointed Service Provider or its authorized service partner repairs or replaces the appliance under the terms of this guarantee, the appointed Service Provider or its authorized service partner will reinstall the repaired appliance or install the replacement, if necessary.

• All plumping and electrical installation, are not the responsibility of IKEA, and customer must complete these work before the execution work.

How country law applies
The IKEA guarantee gives you specific legal rights, which cover or exceed all the local legal demands. However these conditions do not limit in any way consumer rights described in the local legislation.
Area of validity
This warranty is valid only in the country where the product has been purchased; the services will be provided in the framework of the guarantee conditions.
An obligation to carry out services in the framework of the guarantee exists only if the appliance complies and is installed in accordance with:

– the technical specifications of the country in which the guarantee claim is made;
– the Assembly Instructions and User Manual Safety Information.

The dedicated AFTER SALES for IKEA appliances
Please don’t hesitate to contact IKEA appointed After Sales Service Provider to:

• make a service request under this guarantee;
• ask for clarifications on installation of the IKEA appliance in the dedicated IKEA kitchen furniture;
• ask for clarification on functions of IKEA appliances.

To ensure that we provide you with the best assistance, please read carefully the Assembly Instructions and/or the User Manual before contacting us.
How to reach us if you need our service

Please refer to the last page of this manual for the full list of IKEA appointed Authorized Service Centre and relative national phone numbers.

In order to provide you a quicker service, we recommend to use the specific phone numbers listed on this manual. Please also always refer to the IKEA article number (8 digit code) placed on the rating plate of your appliance.
SAVE THE SALES RECEIPT!
It is your proof of purchase and required for the guarantee to apply. The sales receipt also reports the IKEA name and article number (8 digit code) for each of the appliances you have purchased.

UNITED ARAB EMIRATES & OMAN

QATAR| Toll free:
Web| 8 004 532
www.IKEA.com
---|---|---
EGYPT| Hotline:
Web:
e-mail:| 16576
www.IKEA.eg
IkeaCairo.customerservice@alfuttaim.com
STATE OF KUWAIT| Contact centre:
Web:
e-mail:| +965 18 40 40 8
www.IKEA.com.kw
info@IKEA.com.kw

References

• Hej! Welcome to IKEA Global
• Fresh home furnishing ideas and affordable furniture - IKEA
• Enjoy shopping online! Shop furniture & accessories - IKEA
• Fresh home furnishing ideas and affordable furniture - IKEA
• Buy Furniture & Home Accessories Online in Qatar - IKEA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>