iTECHWORLD GoFurther Power Station User Manual

iTECHWORLD GoFurther Power Station

Product Information

• The product is a battery box that is not recommended for jumpstarting a vehicle with a lithium battery. It has a non-slip surface of silicone pads pre-installed. The DCDC alternator input and solar input are unregulated. The output is rated for 175A max output and has a master switch that disconnects everything except the DCDC charger. It also has 4x Anderson plugs connected in a bank of 2x Anderson plugs with a maximum input/output of 50A each bank.
• The battery box has various features such as battery type selection, battery capacity and voltage measurement, low battery alarm, battery temperature protection, and battery protection alarms. The user manual provides detailed instructions for the operation of the product.

Product Usage Instructions

1. Do not try to jumpstart a vehicle with this battery box if using a lithium battery.
2. Connect the DCDC alternator input and solar input to the appropriate sources.
3. Use the non-slip surface of silicone pads to keep the battery box stable.
4. Check your battery type and select LifePO4 as the battery type on the DCDC charger by holding the MODE button for 2 seconds until the battery type light starts flashing. When this occurs, your selection is saved.
5. Ensure that the output does not exceed the rated 175A max output.
6. Use the master switch to disconnect all devices except the DCDC charger and prevent your battery from being drained.
7. Refer to the manual for detailed instructions on battery type selection, battery capacity and voltage measurement, low battery alarm, battery temperature protection, and battery protection alarms.
8. Connect devices to the 4x Anderson plugs connected in a bank of 2x Anderson plugs with a maximum input/output of 50A each bank.

IMPORTANT SAFETY INSTRUCTIONS

• For charging 12V iTECHWORLD lithium LiFePO4 batteries.
• Never attempt to recharge non-rechargeable batteries.
• The lid of the battery box must remain shut at all times whilst charging a battery or powering a device from an outlet.
• Do not allow any metal obiects to fall into the battery box or enter any of the ports.
• Never insert anything other than a compatible electrical plug into any of the ports on the battery box.
• Ensure that the battery box is shut and the screws are tight before powering any devices.
• Do not try to jumpstart a vehicle with this battery box if using an iTECHWORLD lithium battery

OVERVIEW

GETTING STARTED

1. Step 1 : The non-slip surface of silicone pads pre-installed
2. Step 2 : Lower your battery into the battery box base carefully, locating it as centrally as possible on the non-slip pads
3. Step 3: Secure the battery in place by tightening the velcro strap over the battery.
4. Step 4: Install the battery cables onto the terminal posts of the battery. Ensure the red cable is connected to the positive (+) terminal, the black cable connected to the negative (-) terminal. Tighten firmly but be sure not to over-tighten the battery terminals.
5. Step 5 : Tuck cables in under the battery box lid, lowering the lid carefully onto the box – ensuring the lid is correctly oriented
6. Step 6: Install the 4 provided screws to fasten the lid to the base, being sure not to over tighten with the supplied allen key.
7. Step 7 ATTENTION FOR DCDC CHARGER MODELS: Check your battery type. For example: select LifePO4 as the battery type on the DCDC charger by holding the MODE button for 2 seconds until the battery type light starts flashing. When this occurs, your selection is saved.

OPTIONAL ACCESSORIES

MOUNTING TRAY (OPTIONAL)

• Step 1:
  • Confirm install location of tray, drilling any required holes.
  • Install the strap under the tray, sliding the strap into the slots either side.
  • Ensure strap is oriented correctly so that the hooks face toward the Power Station when installed.
  • Securely affix the tray in position using bolts or screws, whichever is applicable.
  • Ensure that washers are used when installing the tray, to avoid damage.
  • Note: We do not provide the screws or bolts for this installation.
• Step 2 : Ensure straps are laying outside the tray before lowering the battery box carefully onto the tray. Attach each strap hook to the corresponding slot in the Power Station.
• Step 3 : For ease of tightening, place thumbs in each strap loop, pushing firmly downwards. The strap should tighten and hold the Power Station firmly in place. To release, depress the buckle and pull the strap to loosen.

Inverter Cables (Optional)

iTECHWOrLD Inverter leads have been designed to allow you to easily connect a high powered inverter to the battery box. When it comes to Inverter cables, there is no substitute for quality and these TeCHWOrLD Inverter Cables have been designed to work flawlessly and to provide a high currentflow to your inverter this output is rated for 175A max output, please do not exceed it.

SWITCHES

The Master Switch
The master switch disconnects everything (except DCDC Charger). Turning it off is a quick way to disconnect all devices to ensure your battery is not being drained.

Note : The DCDC Charger + Solar Regulator still can charge the internal battery while the Master Switch is in the OFF position.

LCD SCREEN
The TECHWORLD GOFURTHER Monitor has a display and two buttons. The screen is used to monitor the state and condition of the battery. The display features the following:

• Battery type
• Battery pack voltage
• Battery Temperature
• Total Capacity of Battery
• Mutable Low Battery Alarm
• Battery Protection Alarms

FOR DETAIL OPERATION REFER TO THE MANUAL

CONNECTIONS OUTPUTS

2 X CIGARETTE SOCKET OUTPUTS

• Maximum 10A output per socket
• 2 X DUAL USB / QC3.0

OUTPUTS

• PD+QC 3.0USB
• 2 x Quick Charge QC 3.0 Ultra
  High Powered USB Outputs

Benefits of Quick Charge C

When paired with compatible devices, a Quick Charge-enabled charger delivers more power, allowing the connected device to charge faster. As one of the most widely used of the fast charging technologies, Quick Charge is already in many of your favorite smartphones. If your smartphone is Quick Charge 3.0- compatible, you can charge up to 80% in just 35 minutes. To future-proof your chargers, each new Quick Charge generation is backward compatible, meaning it will work with the generations that came before.

INPUTS/OUTPUTS

1 X (175A) ANDERSON-STYLE PLUG

• High Current Inverter Output
• Connected directly to battery

WARNING:

1. Master switch Will disconnect the battery from this connector.
2. This output is NOT Fused or Short Circuit Protected.
3. Check battery specifications and compatibility with high current draw before using jump start connector
4. Lithium batteries should not be used for jump starting.

ANDERSON STYLE PLUGS

• Input / Output Capable.
• 4x anderson plugs are connected in a bank of 2x anderson plugs with a maximum input/output of 50A each bank. (one bank is 2 anderson pugs on left and other is right)

WARNING:

1. Do not plug in multiple chargers as inputs.
2. Do not use an external charger while the DC-DC Charger is operating.
3. Exceeding 50A current rating will trigger the safety breaker. Safety breaker will auto-reset in time.

NOTE: THE 4 ANDERSON PLUGS INDICATED CANNOT EXCEED A TOTAL OF 50 AMPS PER BANK OF 2X ANDERSON PLUGS

INPUTS ALTERNATOR

1 X TRIPLE ANDERSON STYLE PLUG

• 9-32V DC Starter Battery Input (+/-)
• Ignition source connection

MPPT SOLAR
1 X (50A) ANDERSON STYLE PLUG

• Minimum Solar Input Voltage: 9V DC
• Maximum Solar Input Voltage: 32V DC
• Maximum Solar Input Current: 25A

Unregulated Solar Input – utilises in built DCDC MPPT regulator. Not suitable for regulated solar input, connect to a standard in/out connector when using an external or panel-mounted solar controller/regulator.

WARNING:

1. Do not exceed the Maximum Voltage of 32V DC
2. Do not exceed the Maximum Input Current of 25A

CONNECTING TO EXTERNAL CHARGERS

TheiTECHWORLD GOFURTHER may be charged in a number of ways:

• Connecting an AC charger to any of the in/out Anderson style connectors.
• Connecting a solar panel with regulator/controller to any of the in/out Anderson style connectors.
• Connecting alternator power to optional DCDC Charger in a vehicle.
• Connecting an unregulated solar panel input to optional DCDC Charger.

Warning:

• Connecting multiple chargers to the battery at any one time is not recommended.
• Do not connect an unregulated solar panel directly to the battery via any of the in/out connectors.

TYPICAL DIAGRAMS

CONNECTING DDC CHARGER

CONNECTING TO ALTERNATOR INPUT

• The /TECHWORLD GOFURTHER includes a built-in DCDC Charger suitable for charging from a vehicle alternator.
• The easiest way to connect the Power Station to your vehicle is by using the iTECHWORLD Plug & Play Wiring Kit (sold separately).
• The triple Anderson style connector fitted to the Power Station interfaces with the
• TECHWORLD Plug & Play Wiring Kit, providing a simple, quick release vehicle charging solution. This triple connector and cable provides alternator power to the DCDC on the
• Power Station, along with an Ignition Source for charging in vehicles that are fitted with Smart or Temperature Compensating Alternator.
• For more information on installing a Dual Battery Wiring Kit and Ignition Wire, please visit www.iTechworld.com.au/pages/HelpCentre

Wiring Kit

Sold Separately

CONNECTING TO UNREGULATED SOLAR
iTECHWORLD GO FURTHER includes a built-in DC-DC Charger with an MPPT regulator suitable for charging from unregulated solar panels. To connect your solar panel to the regulator simply plug it in via the Anderson style plug on your battery box.

Note:

• Your solar panel open circuit voltage must not exceed 32 VoC, the voltage of your panel can generally be found on the sticker on the rear of your solar panel
• If your solar panel is fitted with a built-in regulator, you will need to bypass the regulator port. Alternatively, you can connect your regulated solar panel to any of the 4 in/out anderson style connectors.

FREQUENTLY ASKED QUESTIONS

Q. If storing my iTECHWORLD GOFURTHER for long periods, what should I do to look after my battery’s health?
A lithium battery can be stored at any state of charge due to a very low rate of discharge. It is recommended that if storing for long periods, the battery be charged to a minimum of 70% before switching off the Master Switch and storing.

NOTE: The battery will not go into storage mode if:

• There are loads connected to it.
• It is being charged

Q. Is my iTECHWORLD GO FURTHER Water Proof ?
TheiTECHWORLD GO FURTHER has been designed to be as resistant to moisture and dust as possible, though it is not waterproof.
Do not leave exposed to rain or weather, and do not submerge.

Q. Can I Jump Start with my iTECHWORLD GO FURTHER?
It is not recommended jump starting with the iTECHWORLD GO FURTHER
The information in this document is subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>