AI-Eye VS18210 8MP Motorized Lens Bullet Camera User Guide
- June 11, 2024
- AI-Eye
Table of Contents
AI-Eye VS18210 8MP Motorized Lens Bullet Camera User Guide
1. General
1.1 Accessing via Web Browser Default IP address
1.2 Appearance Description
The overview of the bullet camera is shown below:
1.3 Packing list
Component Camera Drilling sticker Expansion tube Tapping screw
1.4 Cable
2. Installation
2.1 Note
2.1.1 Make sure the device in the package is in good condition and all the assembly parts are included.
You will need the following:
2.2 Caution
Please do not lift a camera by its cable.
Please do not screw-off the screws of the front cove.
2.3 Front cover of the camera removes
- Use a Allen key screwdriver to remover the front cover of camera, and rotator the cover to open it. Then, you can see the Reset button and SD card slot.
2.4 Reset Button
- To restore the camera to factory settings and software reboot the camera, you need to press and hold the reset button 5~10 seconds.
- To restore the camera to factory settings and hardware reboot the camera, you need to press and hold the reset button more than 10 seconds.
2.5 Micro SD card installation
The SD card slot supports only class 6 or higher Micro SD card. To replace a Micro SD card, the device must be powered off. Otherwise, system exception may occur. When a Micro SD card is used for the first time, log in to the web client of the device and format the Micro SD card. For details, see the Configuration Guide.
Please refer to figure 2.5, insert the memory card to memory card slot on the rear housing of the camera. During SD card installation, you are advised to turn the camera maintenance position upward and insert the SD card into the SD card slot from upon to avoid accidentally dropping the SD card into the camera.
2.7 Camera mounting
The suggested mounting height is over 3 meters at least.
The right height and angle of camera is important to ensure image quality. The
figure of the camera is installation requirements for concept and reference
only.
Wall Mounting Installation
Step 1:
Confirm that the cable outlet on the wall is large enough for the pigtails to
pass through (size of hole size inserted here). Affix the drilling sticker to
the camera installation position and ensure that the center of the sticker
matches the cable outlet on the wall.
Step 2:
Use a 5mm drill bit to drill four 35mm deep holes in the positions marked by
the drilling sticker. Use a hammer to carefully drive the white plastic
expansion tubes into the holes.
Step 3:
Connect the external cabling to camera pigtails, insulate the connections (see
Cable Connections), and feed the cabling through the cable entry on the wall.
Fasten the tapping screws. Make sure the cable outlet at the camera base is
installed facing downwards and is sealed with waterproof glue or caulking to
prevent water from getting into the camera.
Step 4:
Loosen the three Philips head screws and adjust the camera to the required
angle. Then re-tighten the screws, and adjust the position of the sunshield.
Wall Mounting Installation with Junction Box and Camera
Step 1
Place the junction box on the wall such that the arrows of bottom point to the
ground as well as. Then use 4 screws to mount the junction box on to the wall.
Step 2
Use 3 screws to fix the camera onto the cover of junction box. Then, clip the
safety rope of the cover of the junction box to the bottom of the junction
box. Thread the cables through the junction and attach them to the camera
pigtails. Finally, tighten the screws to fix the cover onto the junction box
in place.
Pole Mounting Installation with Junction Box
2.11 Cable connection
2.11-1 For safety precautions
The lightning arrester must be installed and grounded if you install camera outdoor. Strong and weak current cables must be kept at least 5 cm apart from each other. When connecting the cables to the device, take care to avoid connecting strong current cables to weak current interfaces or you will damage your device. The tail of cable must be cut if it cannot pass through the wall, please keep the label on tail of cable. And please make sure to use insulating tape and waterproof tape to insulate and waterproof all tail of cable to avoid short circuits and water leakage. Wrap all pigtail cables in insulated, waterproof, rubber tape to prevent short circuits or water damage.
2.11-2 Power cable connection
Connect the power cable to the device.
2.11-3 Ground cable installation
Please connect ground cable of camera to ground.
2.11-4 Audio and alarm cable installation
Connect the ground cable to ground the device, and then connect the power cable. If crimp terminals are not used, the wire thickness cannot exceed 1.5mm2, and the length cannot exceed 25m. If crimp terminals are used, the wire can be up to 0.75mm2 for a 15m length of wiring or up to 1.0mm2 if 20m is required. Longer wiring is not supported. The ground impedance cannot exceed 5 ohms.
2.12 Cable waterproof and insulation
Waterproof and insulate all cables including power cables, network cables, and unused pigtails.
- Wrap one layer of insulation tape around each cable joint.
- Stretch the waterproofing tape evenly to twice its original length. Then apply it for three layers from bottom to top, from top to bottom, and from bottom to top again.
- Stretch the insulation tape evenly to twice its original length. Then apply it for three layers from bottom to top, from top to bottom, and from bottom to top again.to up. Finally tie the upper and lower ends with cable ties. Then use cable ties to secure the both ends.
- Cover the rest of the cabling in a conduit or with protective waterproof rubber tape. Make a drip loop as shown below to create an artificial lowest point of the cable.
3. Check Item
Please confirm the following to ensure that the equipment is installed correctly.
Declaration of toxic and hazardous substances in electronic and electrical products
FCC compliance statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>