i-PRO WV-QSR504 Mount Bracket Instruction Manual

WV-QSR504 Mount Bracket
Instruction Manual WV-QSR504F-W
Operating Instructions
Included Installation Instructions
Mount Bracket
Model No. WV-QSR504

WV-QSR504 Mount Bracket

• Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation or through use of parts other than this product, such as locally procured parts.
“<Control No.: C****>” used in these documents should be used to search for information on our technical information website (https://i-pro.com/global/en/surveillance/trainingsupport/support/technical- information) and will guide you to the right information.

Caution:

• Before attempting to connect or operate this product, please read these instructions carefully.

Notice:

• This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily reach.
• For information about screws and other parts required for installation, refer to the corre- sponding section of this document.

Precautions

• Do not use this bracket except with suitable cameras.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Refer installation work to the dealer.
  Installation work requires technique and experience.
  Failure to observe this may cause fire, electric shock, injury, or damage to the product.
  Be sure to consult the dealer.

• Install the product securely on the bracket by following the installation instructions.
  Failure to observe this may cause injury or accidents.

• The screws and bolts must be tightened to the specified torq ue.
  Failure to observe this may cause a drop resulting in injury or accidents.

• The measures of protection against a fall of this product shall be taken.
  **QSR504F QSR504M QSR504F1 QSR504M1**
  Failure to observe this may cause a drop resulting in injury or accidents.
  Be sure to install the safety wire.

• Do not rub the edges of metal parts with your hand.
  Failure to observe this may cause injury.

When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.

About notations

| Connection part
specifications of this product| Mount bracket
corresponding with this product
---|---|---
**QSR504**
**QSR504S**| 4 holes| WV-QCL501, WV-QWL501
WV-QCL501S, WV-QWL501S
**QSR504F**| Female screw (ISO)
40A, Rp 1-1/2, 11crest
depth 25.4 mm {1 inch}
(parallel thread)| Locally procured
40A, R 1-1/2, 11crest
length 25.4 mm {1 inch} or more
(taper pipe thread)
**QSR504F1**| Female screw (ANSI)
40A, NPSC 1-1/2, 11.5 crest
depth 25.4 mm {1 inch}
(parallel thread)| Locally procured
40A, NPT 1-1/2, 11.5 crest
length 25.4 mm {1 inch} or more
(taper pipe thread)
QSR504M| Male screw (ISO)
40A, R 1-1/2, 11 crest
length 25.4 mm {1 inch}
(taper pipe thread)| Locally procured
40A, NPT 1-1/2, 11.5 crest
length 25.4 mm {1 inch} or more
(taper pipe thread)
**QSR504M1**| Male screw (ANSI)
40A, NPT 1-1/2, 11.5 crest
length 25.4 mm {1 inch}
(taper pipe thread)| Locally procured
40A, NPSC 1-1/2, 11.5 crest
depth 25.4 mm {1 inch} or more
(parallel thread)

Preface

This product is a mount bracket for PTZ camera. Use this product when connecting the WV-S65340 series camera to a ceiling mount bracket, wall mount bracket or a locally procured bracket.
The latest information about the supported cameras
The model number is abbreviated in some descriptions in this manual.

Specifications

Height: 121 mm {4-3/4 inches}
Mass:| Approx. 1.0 kg {2.21 lbs}
Finish:| Main body: Aluminum die cast,
**QSR504 QSR504F QSR504M QSR504F1 QSR504M1**
i-PRO white/black
**QSR504S** Heavy salt damage prevention coating, i-PRO white

Precautions for installation

• In order to prevent injury, this product must be securely mounted to a bracket according to Installation Guide.

• Mounting method for this product
  This product is designed to be used as a pendant mount camera. If it is mounted on a desktop or at a slant, the camera may not work correctly and its lifetime may be shortened.

• Installation place **QSR504S**
  Salt damage prevention is applied to this product. However, it is not completely anti-corrosive. Therefore, consider a place for installation where direct splash of seawater can be avoided. Especially when installing this product in a seashore area or a place where a snow-melting agent is applied, and also where rainwater is avoided, it is recommended to regularly clean and rinse off salt with water. In case of installing this product in a seashore area, regularly check the status of equipment. (Replace the parts as required.)

• Make sure to remove this product if it will no longer be used.

Standard Accessories

Operating Instructions (this document) ……………………………..1 pc.
**QSR504 QSR504S**
Hexagon screw (M6) ……………………………………………………5 pcs. (of them, 1 for spare)
Other items that are needed (not included)
Common

• Screws to fix a locally procured bracket on the installation surface
  **QSR504 QSR504S**

• 5 mm (distance between two parallel sides of a hexagon) hex wrench
  **QSR504F QSR504M QSR504F1 QSR504M1**

• Sealant for waterproof treatment

• Safety wire

• Safety wire fixing screw

• Use a screw having a pull-out strength that is enough to hold the sum of weight of the camera, this bracket, locally procured bracket, wire and cables.

• Select a fixing method in accordance with the installation place surface for a part where the safety wire is to be fixed.

• Use the dedicated tool when processing the wire.

• Maximum weight of locally procured bracket: 5 kg {11 lbs}

Installation

**QSR504 QSR504S**→ Step1→Step2
QSR504F QSR504M QSR504F1 QSR504M1 → Step3 – Step7
Step1
Check of combination of brackets

• Brackets with normal specification
  QSR504 + WV-QCL501
  (Ceiling mount bracket)
  + WV-QWL501
  (Wall mount bracket)

• Brackets with heavy salt damage resistance specification
  QSR504S + WV-QCL501S
  (Ceiling mount bracket)
  + WV-QWL501S
  (Wall mount bracket)

Note:

• Refer to the operating instructions of each bracket for how to fix the brackets to be used with to the installation surface.

Step2 ⇒ Follow the installation procedure described in the installation guide or in the installation procedure leaflet of the camera for the subsequent procedures.

Step3 Check of brackets Step4 Preparations Step5

• Securely fasten when fixing this product.
• Depending on the fixing position of this bracket, the camera may not face the front. Perform an adjustment of the camera direction by panning the camera. Step6 Refer to the installation guide or the installation procedure leaflet of the camera for connection.
Step7 ⇒ Follow the installation procedure described in the installation guide or in the installation procedure leaflet of the camera for the subsequent procedures.

i-PRO Co,Ltd
https://www.i-pro.com/
Ns0522-1122
Printed in China
© i-PRO Co., Ltd. 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>