Cambridge Audio C165SS Premium In Ceiling Stereo Speaker User Manual

Cambridge Audio C165SS Premium In Ceiling Stereo Speaker

Last updated : December 6, 2022 03:49. Revision #8133

Introduction

The C165SS Ceiling Speaker is a high-quality audio device designed for use in residential and commercial settings. It is built with premium materials and advanced technology to deliver clear and immersive sound.

What’s included with the C165SS?
1 x C165SS Ceiling Speaker is included in the package.

Installation Instructions

Follow the steps below for proper installation of the C165SS Ceiling Speaker:

1. Remove the cardboard pad from inside the supplied template to mark the position for the mounting hole at the selected location.
2. Before cutting ceiling speaker holes, it is suggested that the area is tested for clearance by making an L-shaped probe from strong wire (see illustration below), drilling a small hole in the target area, inserting the probe and slowly turning. Any obstructions will be immediately obvious, and the target area can be moved to a more suitable position.

Painting the speaker grille and frame

The C165SS speaker grille is attached by a magnet, allowing it to be easily removed for painting. Follow the steps below to paint the grille:

1. Carefully remove the grille ensuring not to damage the speaker cone.
2. Paint the grille using your chosen paint.
3. If you wish to paint the speaker surround, please use the included clear plastic painting mask to cover the speaker cone and avoid causing damage.

Technical specifications

The technical specifications of the C165SS Ceiling Speaker are as follows:

• Frequency Response: 55Hz – 20kHz
• Power Handling: 50 Watts RMS, 100 Watts Max
• Impedance: 8 Ohms
• Sensitivity: 90dB
• Dimensions (Diameter x Depth): 235mm x 87mm

Manual Generated: 07.03.2023 – 22:57

C165SS Ceiling Speaker
Last updated: December 6, 2022 03:49. Revision #8133

Introduction

• This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully checked for accuracy at the time of printing; however, Cambridge Audio’s policy is one of continuous improvement, therefore design and specifications are subject to change without prior notice.
• This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. All trademarks and registered trademarks are the property of their respective owners.
• © Copyright Cambridge Audio Ltd .
• For upcoming news on future products, software updates and exclusive offers, make sure you register your product at http://www.cambridgeaudio.com/register

What’s included with the C165SS?

Last updated: Januar 19, 2023 01:55. Revision #8397 1. 1 x C165SS Ceiling Speaker.

Installation Instructions

Last updated: Januar 19, 2023 01:55. Revision #8398

1. Firstly, remove the cardboard pad from inside the supplied template to mark the position for the mounting hole at the selected location.
2. Before cutting ceiling speaker holes, it is suggested that the area is tested for clearance by making an L-shaped probe from strong wire (see illustration below), drilling a small hole in the target area, inserting the probe and slowly turning. Any obstructions will be immediately obvious, and the target area can be moved to a more suitable position.
3. Cut the mounting hole with a drywall, or keyhole saw. Be sure the mounting surface is between 10 and 30mm (0.39 – 1.18”) thick, and that there is at least 93mm(3.74”) of clearance behind the mounting surface.
4. Use 16 gauge minimum speaker cable to connect between your amplifier and your speakers. Ensure that speaker cables are routed away from any electrical cables and that any amplifiers/sources are switched off during installation.
5. Use a wire stripper to strip 10mm of insulation from the end of each speaker cable and twist the strands together.
6. When connecting speakers pay extra attention to polarity ensuring that red (+) terminals on your amplifier are connected to the red (+) terminals on your speakers, and that the black (-) terminals on your amplifier are connected to the black (-) terminals on your speakers.
7. Ensure that the four fixing screws on the speaker are slackened off allowing the mounting dog-legs to move freely. Move each dog-leg foot to the LEFT into its holding slot and then line the speaker up in the mounting hole.
8. With the speaker in the mounting hole use a cross-head screwdriver to slowly turn each fixing screw clockwise, moving the dog-legs out of their slots. Tighten these screws until the dog-legs grip the ceiling.
   Note : Please check with your builder/installer whether you need to install a fire hood with this product. “Low smoke/zero halogen” specification Speaker cable may also be required.

Painting the speaker grille and frame

The C165SS speaker grille is attached by a magnet, allowing it to be easily removed for painting.

1. Carefully remove the grille ensuring not to damage the speaker cone.
2. Paint the grille using your chosen paint.
3. If you wish to paint the speaker surround, please use the included clear plastic painting mask to cover the speaker cone and avoid causing damage.

Technical specifications

Last updated: Januar 19, 2023 01:55. Revision #8400

• Sensitivity (SPL) 86dB (2.83 Vrms input)
• Frequency Response 60Hz – 20kHz
• Impedance 4 Ohms
• Drivers
  • 1 x 6.5” (165mm) woofer.
  • 2 x 0.5” (13mm) tweeters.
• Speaker Dimensions (H x W x D) 97 x ø 240mm (3.8 x ø 9.4”)
• Weight 1.28kg (2.8lbs)

References

• Register your product | Cambridge Audio US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>