i-PRO WV-X8571N Network Camera Installation Guide

Installation Guide
Included Installation Instructions
Network Camera
For professional use only
Model No.
WV-X8571N
Outdoor use
WV-S8531N
Outdoor use

WV-X8571N Network Camera

About the user manuals
Product documentation is composed of the following documents.

• Installation Guide (this document): Provides information about “Precautions”, “Precautions for installation” and the installation method.
• Basic Information (in the following website): Provides information about “Precautions for use” and “Detail specifications”.
• Operating Instructions (in the following website): Explains how to perform the settings and how to operate this camera.

https://i-pro.com/global/en/surveillance/documentation_database

“<Control No.: C****>” used in these documents should be used to search for information on our support website
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information) and will guide you to the right information. ![i-PRO WV-X8571N Network Camera

• qr code1](https://manuals.plus/wp-content/uploads/2023/05/i-PRO-WV-X8571N- Network-Camera-qr-code1.jpg)

  • Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
  • SDXC/ SDHC/ SD memory card is described as SD memory card.
  • The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.

Caution:

• The DC power supply connected to the camera must be in the same building.
• The network camera is only intended for a connection to an ethernet or PoE network without routing to the outside plant.
• This product has no power switch. Be sure to install disconnect devices such as a circuit breaker to shut down the main power of power supplying equipment to this product.
• Only connect 12 V DC Class 2 power supply (UL1310/CSA 223) or limited power source (IEC/EN/ UL/CSA 60950-1 or IEC/EN/UL/CSA 62368-1 Annex). (WV-X8571N)
• Before attempting to connect or operate this product, please read these instructions carefully.

Notice:

• This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily reach.
• This product is a professional equipment.
• For information about screws and other parts required for installation, refer to the corresponding section of this document.
  **** : Direct current symbol

Precautions

• Do not insert any foreign objects.
  Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter inside the unit. Turn the power off immediately and contact qualified service personnel for service.

• Do not use this product in an inflammable atmosphere.
  Failure to observe this may cause an explosion resulting in injury.

• Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.
  Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur.

• Do not strike or give a strong shock to this product.
  Failure to observe this may cause injury or fire.

• Keep SD memory cards away from infants and children.
  Otherwise, they may swallow the cards by mistake.
  In this case, consult a doctor immediately.

• Do not hang down from this product or use this product as a pedestal.
  Failure to observe this may cause injury or accidents.

• Do not damage the power cable. X8571
  Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable. Do not place heavy objects on it, and keep it away from heat sources.
  Use of a damaged power cable may cause electric shock, short circuit, or fire.
  Consult the dealer for repair.

• Do not install this product on a place that is greatly influenced by wind.
  Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall of the product resulting in injury or accidents.

• Do not sprinkle more water, exceeding the performance limit of waterproof with a high pressure cleaning machine, etc.
  Fire or electrical shock may be caused by immersion.

• Do not attempt to disassemble or modify this product.
  Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections.

• Do not install or clean the camera, or touch this product, the power cable or the connected cables during thunder storms.
  Failure to observe this may cause electric shock.

• Refer installation work to the dealer.
  Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• Stop the operation immediately when something is wrong with this product.
  When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or damage to the product. In this case, turn the power off immediately and contact qualified service personnel for service.

• Select an installation area that can support the total weight.
  Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or accidents. Installation work shall be started after sufficient reinforcement.

• Periodic inspections shall be conducted.
  Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
  Consult the dealer for the inspections.

• The exclusively designed mount bracket shall be used.
  Failure to observe this may cause a drop resulting in injury or accidents.
  Use the exclusively designed mount bracket for installation.

• The screws and bolts must be tightened to the specified torque.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Turn the power off when do wiring of this product.
  Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire.

• Install this product in a location high enough to avoid people and objects from bumping the product.
  Failure to observe this may cause injury.

• The measures of protection against a fall of this product shall be taken.
  Failure to observe this may cause a drop resulting in injury.
  Be sure to install the safety wire.

• Do not install this product in locations subject to vibration.
  Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.

• Correctly perform all wiring.
  Short circuits in the wiring or incorrect wiring may cause fire or electrical shock.

• The measures of protection against snowfall shall be taken.
  Weight of snow may cause a fall of the product resulting in injury or accidents.
  Protect the product against snowfall by installing it under eaves.

• Install the product securely on a wall or a ceiling in accordance with the installation instructions.
  Failure to observe this may cause injury or accidents.

• Turn the power off when cleaning this product.
  Failure to observe this may cause injury.

• Do not rub the edges of metal parts with your hand.
  Failure to observe this may cause injury.

About notations
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models. The illustrations without any notation are of the illustrations of WV-X8571N.
X8571 :The functions with this notation are available when using the model WV-X8571N (4K model).
S8531 :The functions with this notation are available when using the model WV-S8531N (2M pixel model).

Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU Lesser General Public License), etc.
• Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.
• For details concerning licensing and source code of open source software, click “Click here for OSS information” on “Support” page of the setup menu of this product and read the displayed content.
• Please note that we shall not respond to any inquiries regarding the contents of the source code.

Copyright

Except for open source software licensed under GPL/LGPL and so on, distributing, copying, disassembling, reverse compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition, exporting any software provided with this product violating export laws is prohibited.
Trademarks and registered trademarks

• Microsoft, Windows, Windows Media, Internet Explorer, Microsoft Edge, and ActiveX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Intel and Intel Core are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
• Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe in the United States and/or other countries.
• SDXC Logo is a trademark of SD-3C, LLC.
• iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
• Android and Google Chrome are trademark of Google LLC.
• Firefox is a trademark of the Mozilla Foundation in the US and other countries.
• The word “QR Code” is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.
• All other trademarks identified herein are the property of their respective owners.

Precautions for installation

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

• In order to prevent injury, the product must be securely mounted to a ceiling or wall according to Installation Guide.

• Installation area for this product Select an appropriate place for the installation area (such as a strong wall or ceiling) in your particular environment.

  • Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
  • Install the camera in the foundation area of the architecture or where sufficient strength is assured.
  • Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.

• Mounting method for this product.
  This product is designed to be used as a pendant mount camera. If the product is mounted on a desktop or at a slant, it may not work correctly and its lifetime may be shortened.

• Do not place this product in the following places

  • Locations where a chemical agent is used such as a swimming pool
  • Locations subject to moisture or oil smoke such as a kitchen
  • Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
  • Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
  • Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
  • Locations where the temperature is not within the specified range
  • Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for on-vehicle use.)
  • Locations subject to condensation as the result of severe changes in temperature
  • Locations near rubber products (packing, rubber feet, etc.)

• Screw tightening
  Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.

• Installing in low temperature environments X8571
  This product may not function properly, if it is installed and operated in an environment where the temperature is below –25 °C {–13 °F}. In such a case, wait approximately 2 hours or more until the camera is warmed up. Then, turn on the power again.
  As the camera warms up, snow or frost accumulated on the dome cover will melt. However, it may not be defrosted from the cover depending on the ambient temperature or weather condition.

• Installing in low temperature environments S8531
  This product is equipped with an internal heater unit for use in cold climates. The heater unit turns on automatically when the temperature inside the product drops below around 0°C {32 °F}. When this product is installed and operated in low temperatures below –10 °C {14 °F}, it may require time to start up since the camera will wait to be warmed up internally by the internal heater right after the power is turned on. Also, the camera may not function properly, if it is installed and operated in an environment where the temperature is below –25 °C {–13 °F}. In such a case, wait approximately 2 hours or more until the camera is warmed up. Then, turn on the power again.
  As the camera warms up, snow or frost accumulated on the dome cover will melt. However, it may not be defrosted from the cover depending on the ambient temperature or weather condition.

• About reflection of light from outside or IR light A ghost may appear on the screen depending on the incident angle of external light.
  In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in a part of the screen or the entire screen turning whitish.

  • Refer to our support website for image examples and measures to take.

• Take notice of humidity
  Install this product when the humidity is low. If installation is performed when it is raining or in very humid conditions, the inside may be affected by humidity, causing mist-over inside the dome cover.

• Protection from lightning
  When cables are used outdoors, there is a chance that they may be affected by lightning. In such a case, install a lightning arrestor close to the camera, and make the length of the network cable between the camera and lightning arrestor as short as possible to prevent the camera from being affected by lightning.

• When noise disturbance may happen
  Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and transformers, or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power distribution work to keep 1 m {3.28 feet} away from them or conduct the electric conduit work using metal pipes. (Be sure to make ground connection of the metal pipes.)

• Make sure to remove this product if it will no longer be used.

• This product has no power switch.
  When turning off the power, disconnect the power supply from the 12 V DC power supply X8571 or the PoE+ device.

• About the battery
  A battery is installed inside the camera. Do not leave the battery exposed in environments of excessive heat as a result of sunlight or fire.

• Equipment classification and power source indication label
  Remove the rear cover of this product to refer to the indication label for the equipment classification, power source, and other information.

Specifications

*For further information, refer to the Basic Information.

PoE+ DC 54 V: 350 mA/Approx. 20 W (Class 4 device)  S8531
PoE+ DC 54 V: 390 mA/Approx. 22 W (Class 4 device)
Operating environment Ambient operating temperature:
Ambient operating humidity:| –40 °C to +60 °C {–40 °F to +140 °F}
(Power On range: –20 °C to +60 °C {–4 °F to +140 °F}) 10 % to 100 % (no condensation)
Storage environment  Storage temperature: Storage humidity:| –30 °C to +60 °C {–22 °F to +140 °F} 10 % to 95 % (no condensation)
EXT I/O terminals 3: X8571| ALARM IN1(Alarm input 1/ Black & white input/ Auto time adjustment input) (x1) ALARM IN2 (Alarm input 2/ ALARM OUT) (x1)
ALARM IN3 (Alarm input 3/ ALARM OUT/ AUX OUT) (x1)
Audio input: X8571
For microphone input:
For line input:| ø3.5 mm stereo mini jack (Audio input is stereo.) Recommended applicable microphone: Plug-in power type (Sensitivity of microphone: –48 dB±3 dB (0 dB=1 V/Pa, 1 kHz)) Input impedance: Approx. 2 kΩ (unbalanced)
Supply voltage:  2.4 V ±0.5 V
Input level:  Approx. –10 db
Waterproof 4:| IP66 (IEC 60529), Type 4X (UL50E) / NEMA 4X compliant
Shock resistance:| IK10 (IEC 62262)
Wind resistance:| Up to 40 m/s {approx. 89 mph}
Dimensions:| When using WV-QJB501-W (optional base bracket): ø230 mm × 232 mm (H) {ø9-1/16 inches × 9-1/8 inches (H)} Dome radius 80 mm {3-5/32 inches}
When using attachment plate only: ø230 mm × 196 mm (H) {ø9-1/16 inches × 7-23/32 inches (H)} Dome radius 80 mm {3-5/32 inches}
Mass:| When using WV-QJB501-W: Approx. 3.3 kg {7.28 lbs} X8571 (optional base bracket) Approx. 3.2 kg {7.06 lbs} S8531
When using attachment plate only: Approx. 2.8 kg {6.18 lbs}  X8571
Approx. 2.7 kg {5.96 lbs} S8531
Finish:| Main body: Aluminum die cast, i-PRO white
Outer fixing screws: Stainless steel (Corrosion-resistant treatment)
Dome cover: Polycarbonate resin (with Clear Sight coating), Clear
Others:| Tamper-resistant enclosure *5

1 Refer to our support website for further information about Power source and Power consumption information.
2 When used with DC 12 V power source, some functions to be added on update may sometimes be unavailable. It is recommended to use with PoE+.
3 Refer to the Operating Instructions for further information about the EXT I/O terminal settings.
Input specification : No-voltage make contact input (4 V – 5 V DC, internally pulled up)
OFF : Open or 4 V – 5 V DC
ON : Make contact with GND (required drive current: 1 mA or more)
Output specification : Open collector output (maximum applied voltage: 20 V DC)
OPEN : 4 V – 5 V DC by internal pull-up
CLOSE : Output voltage 1 V DC or less (maximum drive current: 50 mA)
4 Only when installation work is properly performed according to the Installation Guide and appropriate waterproof treatment is performed.
*5 Component that has a structure on which the screws that are accessible after installation cannot be screwed or unscrewed using an ordinary screwdriver.
*Optional accessories¹**

1. Refer to our support website <Control No.: C0501, C0112> for further information about optional accessories.
2. This product can only be installed indoors when WV-Q105A is used to install it on the ceiling.

Standard accessories

Installation Guide (this document) ………………… 1 pc.
IMPORTANT SAFETY INSTRUCTIONS …………. 1 pc.
Code label*¹…………………………………………….. 1 pc.
The following parts are used during installation procedures.
Attachment plate ………………………………………. 1 pc.
Template A (for the attachment plate) ………….1 sheet
Ferrite core X8571 ……………………………… 1 pc.
Waterproof tape ………………………………………… 1 pc.
RJ45 waterproof connector cover ……………….. 1 pc.
RJ45 waterproof connector cap ………………….. 1 pc.
Bit (Hex wrench, screw size 6.35 mm {1/4 inches} T20) …………………… 1 pc.
4P alarm cable X8571 …………………………. 1 pc.
2P power cable X8571 ………………………… 1 pc.
Wire lug plate …………………………………………… 1 pc.
Extended safety wire …………………………………. 1 pc.
Rain wash coating label ……………………………… 1 pc.
Other items that are needed (not included)

• Fixing screw

Junction box : Mount the camera on the two-gang junction box using the attachment plate| M4/ 4 pcs.| 539 N {121 lbf}
Directly mount : Directly mount the camera onto the ceiling using the attachment plate
QJB501 : Mount the camera onto the ceiling using WV-QJB501-W
: Mount the camera using WV-QSR502A-W (option), QSR502 etc.| Refer to the operating instructions of each bracket.

1 Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.
2 For information about the minimum pull-out strength, refer to our support website .

• RJ45plug, Ethernet cable (category 5e or better, straight, all 4 pairs (8 pins))
• As necessary, audio input cable, audio output cable, alarm I/O cables, power supply cable
• Tools

Parts and functions

Indicators

Note:

• Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or blinking.) Refer to the Operating instructions for information about settings.

LINK indicator
When the camera is able to communicate with the connected device………………………Lights orange
ACT indicator
When data is being sent via the network camera……………………………………………..Blinks green (accessing)
SD MOUNT indicator

When an SD memory card is inserted and could be recognized
When data can be saved after the SD memory card is inserted and the SD ON/OFF button is pressed (less than 1 second)
When data can be saved to the SD memory card
When the SD memory card is removed after holding down the SD ON/OFF button (about 2 seconds)
When data cannot be saved to the SD memory card because an abnormality was detected or the SD memory card is configured not to be used| Lights off → Blinks green
→ Lights off
Lights off → Lights green
Lights green
(recording) Lights green →
Blinks green → Lights off
(waiting for recording)Lights green → Lights off
Lights off
---|---
SD ERROR indicator X8571 SD ERROR/AF indicator S8531
When AF (Auto Focus) operation is being executed S8531
When the network camera is being started
When an SD memory card is recognized normally
When the SD slot is not used or an abnormality is detected in SD memory card after the camera has started| Blinks red (Interval of 1 time/ second)
Lights red
Lights red → Lights off
Lights red → Stays red
---|---

Buttons

• INITIAL SET button (Initializing)
  Follow the steps below to initialize the network camera. Retry if the camera does not start up normally.

The camera will start up and the settings including the network settings will be initialized

• Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and may cause malfunction.

  • SD ON/OFF button
  • When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights up in green and data can be saved to the SD memory card.
  • When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights off and the SD memory card can be removed.

Step1 Processing the installation surface (process according to the installation type)
Common

• Attach the attachment plate (accessory) so that the marking (part number) faces toward the ceiling or wall to be installed.

Junction box

1. Install the junction box on the installation surface.
2. Mount the attachment plate to the junction box. Minimum pull-out strength: 539 N {121 lbf} (per 1 pc.)

Directly mount

1. Drill a hole in the installation surface using template A (accessory). (4 screw holes / 2 cable access holes)
   Note:
   • Make a hole so as to face the FRONT mark of the template to the front side of the camera (in the direction of i-PRO logo).
   • If you want to be able to change the direction of the camera after installation, drill through a 73 mm {2-7/8 inches} diameter hole in the center. By doing so you can adjust the mounting direction of the camera in 90° increments.

2. Install the attachment plate on the installation surface.
   Minimum pull-out strength: 539 N {121 lbf} (per 1 pc.)

QJB501

1. Make a hole on the installation surface using template B (accessory of WV-QJB501-W). (Screw holes (M4:4 places) / Cable access hole (1 place)

• The cable access hole is unnecessary when using a conduit.
• Select either of the two cable access holes of template B to proceed with the installation work.
• Depending on the condition of the ceiling surface, five patterns of screw positions are available for fixation. Select a pattern from the following table and make holes.

| Vertical| Horizontal
---|---|---
A| 85 mm {3-11/32 inches}
(85.7 mm {3-3/8 inches})| 85 mm {3-11/32 inches}
(85.7 mm {3-3/8 inches})
B| 138 mm {5-7/16 inches}| 138 mm {5-7/16 inches}
C| 83.5 mm {3-9/32 inches}| 46 mm {1-13/16 inches}
D| 63 mm {2-15/32 inches}| 63 mm {2-15/32 inches}
E| Do not use Position E.|
F| 70 mm {2-3/4 inches}| 108.5 mm {4-9/32 inches}

When using a conduit
Remove the cap for the female thread for the conduit using a 5mm {3/16 inches} hexagon wrench and attach the conduit.
The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

1. Install WV-QJB501-W on the installation surface. Minimum pull-out strength: 539 N {121 lbf} (per 1 pc.)
2. Mount the attachment plate onto the base bracket. Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

IMPORTANT:

• Installation work shall be such that there is no exposure to water into the architecture through the conduits having been joined.
• If open wiring is conducted, be sure to use conduits and run the cables inside the tubes to protect the cables from direct sunlight.

QSR502
Install on a wall or celling by combining WV-QSR502A-W (optional mount bracket) with WV-QWL501-W (optional wall mount bracket) or WV-QCL501-W (optional ceiling mount bracket).

1. Install the attachment plate (accessory) onto WV-QSR502A-W using the fixing screws for the attachment plate (4 pcs.) (accessory of WV-QSR502A-W).
   Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

2. Fix at the installation place by combining each bracket.

• Refer to the manual of each bracket for how to attach the bracket.

Step 2 Preparation for cable connection X8571
When using the power supply cable, the EXT I/O cable, or the audio input cable, remove the cable case fixed by 4 screws at the upper side of the camera and pull out the power supply cable, the EXT I/O cable, and the audio input cable stored inside.

IMPORTANT:

• Alarm I/O cable / Audio input cable with the ferrite core (accessory) must be used for EMS (Electromagnetic Susceptibility). (Refer to the right illustration)

Step 3 Fixing the brackets (Attach the safety wire)

1. When using other than QSR502 , attach the wire lug plate (accessory) on the ceiling by following the instructions below. (When using QSR502 , go to 【2】.)
2. Bore a hole near the position where the camera is to be installed to fix the wire lug plate.

• The illustration on the right shows the available range for fixing the wire lug plate for the camera installation. 2. Fix the wire lug plate with an M6 bolt-nut or anchor (locally procured).
  Minimum pull-out strength: 724 N {163 lbf}

  2. Attach the safety wire to the wire lug plate.