BOSE DesignMax DM10S-SUB Surface-Mount Subwoofer Installation Guide
- June 11, 2024
- Bose
Table of Contents
PROFESSIONAL
Design Max DM10S-SUB Surface-Mount Subwoofer
Installation Guide
Design Max DM10S-SUB
Surface-mount Subwoofer
Important Safety Instructions
Please read and keep all safety and use instructions.
This product is intended for installation by professional installers only!
This document is intended to provide professional installers with basic
installation and safety guidelines for this product in typical fixed-
installation systems. Please read this document and all safety warnings before
attempting installation.
Do not attempt to service this product yourself. Refer all servicing to
authorized service centers, installers, technicians, dealers or distributors.
To contact Bose Professional or to find a dealer or distributor near you,
visit PRO.BOSE.COM.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produces heat.
- Only use attachments/accessories specified by the manufacturer.
WARNINGS/CAUTIONS
This product contains magnetic material. Consult your physician on whether this might affect your implantable medical device.
- All Bose products must be installed in accordance with local, state, federal and industry regulations. It is the installer’s responsibility to ensure installation of the loudspeakers and mounting system is performed in accordance with all applicable codes, including local building codes and regulations. Consult the local authority having jurisdiction before installing this product.
- Unsafe mounting or overhead suspension of any heavy load can result in serious injury or death, and property damage. It is the installer’s responsibility to evaluate the reliability of any mounting method used for their application. Only professional installers with the knowledge of proper hardware and safe mounting techniques should attempt to install any loudspeaker overhead.
- Do not mount the product in locations where it may be exposed to water or condensation.
- This product is not intended for installation or use in indoor water facility areas (including, without limitation, indoor pools, indoor water parks, hot tub rooms, saunas, steam rooms and indoor skating rinks).
- Do not mount on surfaces that are not sturdy, or that have hazards concealed behind them, such as electrical wiring or plumbing. If you are not sure about installing the bracket, contact a qualified professional installer. Ensure the bracket is installed according to local building codes.
- Use only the hardware and accessories included or specified by Bose for use with Design Max DM10S-SUB loudspeakers. Hardware for securing the loudspeaker to the mounting surface is not supplied. For information on compatible accessories, see the product’s technical data sheet at PRO.BOSE.COM.
- Keep the product away from fire and heat sources. Do not place naked flame sources, such as lighted candles, on or near the product.
- Do not make unauthorized alterations to this product.
- The Design Max DM10S-SUB wall mounting bracket is only for use with model DM10S-SUB.
- Clean speakers using only a dry cloth. Do not expose loudspeaker to soap, detergent, mineral oil, alcohol or other cleaning agents or chemicals.
Product Ratings:
Input Voltage: 70V/100V
Impedance: 8 Ω, 250 W
Current or Power: (70V): 20W, 40W, 80W, 150W; (100V): 40W, 80W, 150W
Regulatory Information
This product conforms to all applicable EU directive requirements. The
complete declaration of conformity can be found at:
www.Bose.com/compliance.
**** This product conforms to all applicable Electromagnetic Compatibility
Regulations 2016 and all other applicable UK regulations. The complete
declaration of conformity can be found at:
www.Bose.com/compliance
This symbol means the product must not be discarded as household waste, and
should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
China Restriction of Hazardous Substances Table
Names and Contents of Toxic or Hazardous Substances or Elements
| Toxic or Hazardous Substances and Elements
Part Name| Lead (Pb)| Mercury (Hg)| Cadmium (Cd)| Hexavalent (CR(VI))|
Polybrominated Biphenyl
(PBB)| Polybrominated diphenyl ether (PBDE)
PCBs| X| 0| 0| 0| 0| 0
Metal Parts| X| 0| 0| 0| 0| 0
Plastic Parts| 0| 0| 0| 0| 0| 0
Speakers| X| 0| 0| 0| 0| 0
Cables| X| 0| 0| 0| 0| 0
This table is prepared in accordance with the provisions of SJ/T 11364.
0: Indicates that this toxic or hazardous substance contained in all of the
homogeneous materials for this part is below the limit requirement of GB/T
26572.|
X: Indicates that this toxic or hazardous substance contained in at least one
of the homogeneous materials used for this part is above the limit requirement
of GB/T 26572.
Taiwan Restriction of Hazardous Substances Table
Equipment name: Design Max DM10S-SUB, Type designation: 829380
| Restricted substances and its chemical symbols
Unit| Lead
(Pb)| Mercury
(Hg)| Cadmium
(Cd)| Hexavalent chromium (Cr+6)| Polybrominated
biphenyls (PBB)| Polybrominated Biphenyl ethers (PBDE)
PCBs| –| 0| 0| 0| 0| 0
Metal Parts| –| 0| 0| 0| 0| 0
Plastic Parts| 0| 0| 0| 0| 0| 0
Speakers| –| 0| 0| 0| 0| 0
Cables| –| 0| 0| o| 0| 0
Note 1: “0” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 2: The “-” indicates that the restricted substance corresponds to the
exemption.
Date of Manufacture: The eighth digit in the serial number indicates the
year of manufacture; “7” is 2007 or 2017.
China Importer: Bose Electronics (Shanghai) Company Limited, Part C,
Plant 9, No. 353 North Raying Road, China (Shanghai) Pilot Free Trade Zone
EU Importer: Bose Products B.V., Gershan 60, 1441 RG Referendum, The
Netherlands
Mexico Importer: Bose de México, S. de R.L. de C.V. , Paseo de las Palmas
405-204, Lomas de Chapultepec, 11000 México, D.F. For importer & service
information: +5255 (5202) 3545
Taiwan Importer: Bose Taiwan Branch, 9F-A1, No. 10, Section 3, Minhang
East Road, Taipei City 104, Taiwan. Phone Number: +886-2-2514 7676
UK Importer: Bose Limited, Bose House, Quayside Chatham Maritime,
Chatham, Kent,
ME4 4QZ, United Kingdom
Bose and Design Max are trademarks of Bose Corporation.
Bose Corporation Headquarters:
1-877-230-5639
©2021 Bose Corporation. No part of this work may be reproduced, modified,
distributed or otherwise used without prior written permission.
Warranty Information
This product is covered by a limited warranty.
For warranty details, visit PRO.BOSE.COM.
Package Contents
Product Dimensions
Technical Specifications
For additional specifications, see the Design Max DM10S-SUB technical data sheet at PRO.BOSE.COM.
Physical
Product Dimensions| Height: 502 mm (19.78 in)
| Width: 316 mm (12.45 in)
| Depth: 323 mm (12.70 in)
Net Weight, Loudspeaker with grille and bracket| 16.10 kg (35.5 lb)
Shipping Weight| 18.82 kg (41.5 lb)
Important Installation Information
This product is intended for indoor use only.
It is the installer’s responsibility to ensure installation of the
loudspeakers and mounting system is performed in accordance with all
applicable codes, including local building codes and regulations. Consult the
local authority having jurisdiction before installing this product.
It is the responsibility of the installer to ensure the safety of the
loudspeaker installation. Failure to properly install the loudspeaker could
result in damage, injury, or death.
Do not mount the product in locations where it may be exposed to water or
condensation.
Do not mount the product in locations where condensation may occur.
This product is not intended for installation or use in indoor water facility
areas (including, without limitation, indoor pools, indoor water parks, hot
tub rooms, saunas, steam rooms and indoor skating rinks). Do not block any
ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produces heat. The
hardware for securing the loudspeaker to the mounting surface is not
supplied. Consult a building professional for the proper mounting hardware
before installing the loudspeaker.
Do not mount on surfaces that are not sturdy, or that have hazards concealed
behind them, such as electrical wiring or plumbing. If you are not sure about
installing the bracket, contact a qualified professional installer. Ensure
the bracket is installed according to local building codes.
Wiring the Loudspeaker
Wire Gauge
The Design Max DM10S-SUB loudspeaker is designed to work with 18 AWG (0.8 mm2
) to 14 AWG (2.1 mm 2 ) size wire only.
Connection Diagrams
Expose six millimeters (1/4 inch) of bare wire to attach to the terminals.
Note: The loudspeaker is not rated for use with a rigid conduit. The
loudspeaker is suitable for a flexible conduit or wiring connection
only.
Loudspeaker Settings
70V
40W| 40W| 80W| 150W*| 8Ω
20W| 20W| 150W| NC**
100V|
- Factory default
NC: No Connection (do not use)
Transformer Tap Setting**
Set tap by turning. Use a flat head screwdriver.
Using a Safety Cable
Some regional construction codes require the use of a secondary method of
securing loudspeakers to support structures to provide additional safety.
Choose a mounting position, method, and hardware consistent with local
building codes and regulations.
A safety cable can be attached to the loudspeaker using the threaded insert on
the back of the enclosure. The insert is sized for an M8 screw (not included)
with a depth of 15 millimeters (0.59 inches).
Installation Options
There are two pairs of slots used to secure the loudspeaker to the mounting
bracket, located on the back and side of the loudspeaker. There are two
different loudspeaker mounting positions: horizontal and vertical. See the
table to the right to choose the installation option best suited for your
installation.
Note: Installation in close proximity to cooking surfaces where the
loudspeaker may be directly exposed to cooking oils, such as in commercial
cooking environments, may decrease the performance or functionality of the
loudspeaker.
Installing the Bracket
Note: When choosing an installation location, at least one of the
mounting bracket’s attachment points must be secured to a support structure.
Attachment points not secured to a support structure must be secured using
appropriate hardware for the installation. Choose fasteners that are
consistent with all local building codes and requirements.
Note: Choose appropriate fasteners to support the weight of the
loudspeaker (16.10 kg [35.5 lb]).
- Mark the drill holes.
- Drill four holes (sized for appropriate fasteners) into the wall.
- Secure the bracket to the wall with four screws (not included). Note: Use M6 or 1/4-inch sized screws.
Wiring the Connector
- Feed the wires through the center hole of the bracket.
- Remove the connector from the loudspeaker.
- Wire the connector. For wiring information, see Wiring the Loudspeaker on page 4.
Installing the Loudspeaker
WARNING: Failure to follow the steps below could lead to an unsafe
mounting condition, which could create a falling hazard.
Note: A 6-millimeter hex key is required for proper installation.
- Attach the loudspeaker to the bracket by sliding the arms of the bracket into the slots on the loudspeaker, either on the back or side of the loudspeaker depending on your chosen loudspeaker position (see Installation Options on page 5).
- Insert one of the included M8 screws into the hole on each side of the loudspeaker.
- Tighten the screws using the hex key to secure the loudspeaker to the bracket.
- Insert one rubber cap into the hole on each side of the loudspeaker.
Rotating the Logo
You can rotate the Bose logo to align with your loudspeaker orientation. To
rotate the logo, first remove the grille by removing the three screws on each
side of the grille.
With one hand, press the button on the back of the grille. Rotate the logo
with the other hand. The logo can be rotated clockwise or counterclockwise.
Once you’ve rotated the logo to your desired orientation, replace the grille
and secure it into place with the six screws.
Note: Do not pinch the button inward unless you intend to remove the
logo.
Safety and Regulatory Compliance
The Bose Design Max DM10S-SUB loudspeaker has passed testing and complies with
the following specifications and uses:
Listed to ANSI/UL 1480A-2016, Speakers for Commercial & Safety Professional
Use
General-Purpose Use – UL Category UEAY, File Number S 5591 Control Number 3N89
Suitable for installation using Class 1, Class 2, Class 3 wiring methods in
accordance with NFPA 70, National Electrical Code, 2017, Article 640
The Design Max DM10S-SUB loudspeaker has been designed to the requirements
defined in the following European regulatory specification for combination
systems:
Tested to IEC60268-5, 2007
PROFESSIONAL
©2021 Bose Corporation, All rights reserved.
Framingham, MA 01701-9168 USA
PRO.BOSE.COM
AM837253 Rev. 02
November 2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>