BY MASSON 017152 Bianco Large Conical Ribbed Pendant Instruction Manual

BY MASSON 017152 Bianco Large Conical Ribbed Pendant Instruction Manual

To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this luminaire. Please keep instructions for future reference.

Installation Requirements

• Must be assembled and installed by a licensed electrician.

• All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
  E.g. AS/NZS 3000 Electrical Installations.

• Do not exceed the maximum wattage rating.

• Select a suitable location for installation:

  • This luminaire is suitable for indoor use only.
  • The mounting point must support 2 times the weight of the luminaire.
  • Ensure the luminaire is not installed in direct line of an air vent/system.
  • If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure no components are missing before assembling.
  If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the luminaire has been damaged during transport. Do not operate/install any product whichappears damaged in any way.
  Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.

2. Determine the suspension length required for your installation by loosening the cord anchorage (H) and adjusting the length of the suspension cord (I).Tighten the cord anchorage (H), take care not to overtighten and damage the cord.

3. Remove the mounting bracket (C) from the canopy (G) by loosening the screws (B) on the sides.

4. Use the mounting bracket (C) as a template to mark the screw positions on the ceiling.

5. Install the mounting bracket (C) onto the ceiling by using appropriately sized mounting screws (D) and anchors (A).
   Ensure the screws (D) and anchors (A) used are suitable for the mounting surface and the surroundingenvironment.

6. Connect the mains supply wire to the terminal block (F).
   Mains Supply Wire| Luminaire Wire / Terminal Block
   ---|---
   Earth – Yellow/Green| Yellow/Green
   Neutral – Blue or Black| Blue or N
   Live – Brown or Red| Brown or L

NOTE: This luminaire is a Class I product and must be earthed during wiring and installation.

7. Ensure the wires are secure and no bare wires are exposed.
8. Install the canopy (G) back onto the mounting bracket (C) and secure by tightening the screws (B) on the sides.
9. Position Shade (J) onto the light fixture (K).
10. Install a lamp (L – not included) into the lamp holder of light fixture (K). Do not exceed the maximum wattage rating.
11. After the installation, switch on the luminaire to test all the lighting functions and enjoy your new luminaire.
    

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the lamp or making any adjustment to the luminaire.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.

Specifications

SKU #: 017152
Colour: White
Rated Voltage: 220-240V~ 50Hz
Rated Wattage: Max. 45W
Lamp Holder: ES/E27
Weight: 4.5kg
Canopy Dimensions: H:30mm Dia:100mm
Luminaire Dimensions: H:180mm Dia:500mm Susp:2000mm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>