Fisher Paykel DW60UT4I2 Built Under Dishwasher Installation Guide

Fisher Paykel DW60UT4I2 Built Under Dishwasher

The Integrated DW60UT4I2, DW60U4I2, and DW60U2I2 models are built-under dishwashers that are designed for indoor use only. These dishwashers should be installed by a qualified plumber and electrician to ensure compliance with local building and electricity regulations.

Safety and Warnings

It is important to follow the safety instructions listed below to reduce the risk of fire, injury, or damage when using the dishwasher:

• Ensure that all water connections are turned off before installation.
• The dishwasher must be installed to allow for future removal from the enclosure if service is required.
• The switched power outlet must be outside the dishwasher cavity and accessible after installation.
• Care should be taken during installation or removal to reduce the likelihood of damage to the power supply cord and hoses.
• Only new hoses supplied with the dishwasher should be used for the connection. Old hoses should not be reused.
• The dishwasher should be placed between cabinetry to ensure stability and prevent damage or injury.
• Do not operate the appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts.
• Do not store or use flammable liquids near the dishwasher.
• Connect the dishwasher to a properly rated, protected, and sized power supply circuit to avoid electrical overload.
• Ensure that the power supply cord is located where it will not be stepped on, tripped over, or otherwise subject to damage or stress.
• Do not install or store the dishwasher where it will be exposed to temperatures below freezing or weather conditions.
• Do not use an extension cord or portable electrical outlet device to connect the dishwasher to the power supply.
• The dishwasher must be earthed in the event of a malfunction or breakdown.

Installation Guide

It is recommended that installation is carried out by a qualified plumber and electrician. The following steps should be followed:

1. Ensure that all water connections are turned off before installation.
2. Install the dishwasher to allow for future removal from the enclosure if service is required.
3. Ensure that the switched power outlet is outside the dishwasher cavity and accessible after installation.
4. Place the dishwasher between cabinetry to ensure stability and prevent damage or injury.
5. Connect the dishwasher to a properly rated, protected, and sized power supply circuit to avoid electrical overload.
6. Ensure that the power supply cord is located where it will not be stepped on, tripped over, or otherwise subject to damage or stress.
7. Do not install or store the dishwasher where it will be exposed to temperatures below freezing or weather conditions.
8. Do not use an extension cord or portable electrical outlet device to connect the dishwasher to the power supply.
9. Earth the dishwasher in the event of a malfunction or breakdown.

It is important to note that failure to install the dishwasher correctly could invalidate any warranty or liability claims. At the completion of the installation, the installer must perform a test run to ensure that the dishwasher is functioning correctly.

SAFETY AND WARNINGS

! WARNING!

| Electric Shock Hazard

Failure to follow this advice may result in electrical shock or death.

•    This appliance must be earthed.  This appliance has a cord with an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local regulations.

•   WARNING – Improper connection of the equipment-earthing conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are unsure if the appliance is properly earthed.

•    Do not modify the power supply plug provided with the appliance. If a different outlet is required have it installed by a qualified electrician? Do not use an extension cord, adapter plug or multi-box.

! WARNING!

| Cut Hazard

Failure to use caution could result in injury.

•     Take care – panel edges are sharp.

! WARNING!

| Weight Hazard

Failure to follow this advice may result in damage or personal injury.

•    Do not attempt to lift this product unassisted.

WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance.

Servicing
Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person

Installation

• Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.

• The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

• The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation.

• This dishwasher is manufactured for indoor use only.

• Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses.

• If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage.

• Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should not be reused.

• Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

• Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an unstable product, which may cause damage or injury.

• Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or has missing or broken parts, including a damaged power supply cord or plug.

• Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the dishwasher.

• Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.

• Make sure that the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress.

• Do not install or store the dishwasher where it will be exposed to temperatures below freezing or exposed to weather.

• Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket outlet box) to connect the dishwasher to the power supply.

• This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current.

• This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.

• EARTHING INSTRUCTIONS – This appliance must be connected to a earthed metal, permanent wiring system, or an equipment-earthing conductor must be run with
  the circuit conductors and connected to the equipment-earthing terminal or lead on the appliance.

• Ensure the product is not plugged in when fitting custom panels.

• Installation of custom panels requires basic mechanical and electrical skills.

• Installation must comply with your local building and electricity regulations.

• Failure to install the custom panels correctly could invalidate any warranty or liability claims.

• Be sure to leave these Instructions with the Customer.

• At the completion of the dishwasher installation, the Installer must perform the Final Checklist.

• Remove all packaging materials supplied with the dishwasher.

• If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product

SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer

COMPONENTS REQUIRED

PARTS

• Keep all packing materials until the unit has been inspected.
• Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage.
• Fisher & Paykel is not responsible for shipping damage.

Supplied

TOOLS

Not supplied

Supplied

PRODUCT DIMENSIONS

CUSTOM PANEL DIMENSIONS

Material specifications

• Maximum weight of door panels must not exceed 10kg (including handle)
• The panel should be adequately sealed to withstand moisture (50°C @ 80% RH). The back and sides of the panel should be completely sealed with a waterproof vapour barrier, such as polyurethane, to prevent damage.
• Installation outside these specifications may result in condensation on cabinetry surfaces.

Toe kick considerations
Depending on the desired toe kick recess depth and door panel extension, the toe kick panel height may need to be adjusted to allow adequate door swing .

CABINETRY

DIMENSIONS

depending on adjustment of levelling feet
including 19mm door panels on adjacent cabinetry
For more information on service requirements, refer to ‘Plumbing & electrical considerations’ and ‘Cabinetry preparation’.

CLEARANCES

PLUMBING & ELECTRICAL CONSIDERATIONS

Hose and cord lengths

• Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements.
• The drain hose should not extend more than 4m. A longer drain hose will cause reduced performance

Water connection

• The dishwasher should not be connected to a water system where there is no temperature control, unless the system is fitted with a suitable tempering valve.
• The dishwasher must not be connected to an undersink high-pressure push-through hot water system, as damage to the system will result.
• Maximum water temperature: 60°C
• 3/4 BSP connector water inlet hose
• Ensure water connection complies with local plumbing regulations

Water pressure

• 0.03-1MPa

Electrical requirements

• 230V, 50Hz, 10A

Anti-flood protection

• This dishwasher has anti-flood protection, which will stop the water flowing in the event of a leak within the machine

excluding plug
standpipe install illustrated. Distance is the same for all plumbing installs

SERVICE ACCESS

• We recommend locating the service holes on either side of the Dishwasher as shown.
• If the holes are created through wood, ensure the edges are smooth and rounded
• If the holes are created through metal, ensure an edge protector is fitted

UNPACK PRODUCT

• Cut straps, lift carton off product and remove the top cap. Dispose of packaging responsibly.
• Remove the install kit, any internal packaging, all rubber bands and all tape.

CABINETRY PREPARATION

• Ensure all minimum cabinetry and service specifications have been met and that all services will be accessible after installation.
• Ensure cabinetry floor is free from bumps and obstructions that could prevent the Dishwasher from sliding into the cavity.
• Align the supplied moisture protection tape to the cabinetry as shown.
  Ensure this area is free of debris before carefully applying the tape to the surface.

DOOR PANEL PREP

• Ensure door panel meets all specifications.
• Using the template as a guide, pre-drill all holes into the panel.
• Ensure the sliding bracket is oriented correctly before securing it to the panel.
• Loosely fit both 16mm Philips hanging screws onto the door panel. Ensure there is a minimum space of 3 mm between the screw-head and the panel.

PUSH INTO CAVITY

• Using a flat-bladed screwdriver, turn to raise the leveling feet. Level the rear, and outside legs first followed by the front legs. Do not adjust the rear middle leg yet.

• Remove both screw covers before partially pushing the product into the cavity, pulling the hoses through as you push to avoid crushing or twisting them. Take care not to bend the legs.
  Push the product from the outside edges to avoid door damage.

• Check the product sits level within the cavity.
  If required, the rear middle leg can be adjusted from the front of the product using a 5mm Allen key.

• Select desired spacer width and cut to size. Remove the adhesive and fit two spacers to each side of the product.
  Push the product into the cavity from the outside edges.

SECURE DOOR PANEL

• Align the door panel to the product. Slot slider bracket and upper screws into place. Slide the panel upwards to lock it into place.
• Align door panel to surrounding cabinetry. Open the door and secure the panel to the product using 4 x screws.

FIT EXIT VENT

• Measure the custom panel overhang from the base of the inner door.
  Refer to the table below for the recommended cut location.

• On a protected surface, carefully cut the vent at the desired location.

• Slot the exit vent into the product and secure using two 3.5x11mm screws.

Not required for DW60U2I2 models

BALANCE DOOR

• Use a 4mm Allen key to adjust the door tension. Rotate clockwise to increase tension, and rotate counterclockwise to decrease tension.
  Ensure both sides are adjusted evenly.

• Open the door at a 45° angle and ensure it holds. If the door does not stay open, repeat the above step.

SECURE TO CAVITY

1. Loosely fit 2 x side fixing screws.
2. If needed, adjust the Dishwasher within the cavity before tightly securing in place. Replace the screw covers.
3. Secure to benchtop using 2 x screws if possible.

INSTALL SOUND SEAL & TOE KICK

FIT SOUND SEAL

• Align both sound seal sheets to the base of the dishwasher. If required, trim excess felt.
• Ensure the door swing is unobstructed before securing the seals using the provided washers and 4.2 x 50mm screws.

CONTINUOUS TOE KICK PANEL

• Align toe kick to product and ensure all door swing clearances have been met.
• Fit panel to surrounding cabinetry

CUSTOM TOE KICK PANEL

1. Mark the pilot hole locations for each bracket. Measure the centre of the panel and mark 237mm to each side.
   To determine the height of the brackets, measure the height of the lowest bracket hole against the toe kick panel.

2. Ensure brackets are oriented correctly before fitting to the panel using 2 x screws per bracket.

3. Measure the toe kick depth:

4. Use Z to determine which tooth to bend back on each toe kick bracket.

5. Align the brackets to the slots on the product and slide into place.

Ø38MM STANDPIPE INSTALLATION

• Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to ‘Plumbing & electrical considerations’ for minimum install heights.
• Pull the hose through the support guide and rest in standpipe.
  • Ensure the drain hose does not extend into water retained in the trap; an air gap is required to prevent wastewater from siphoning back into the tub.
• Ensure the rubber washer is fitted when connecting the inlet hose to the tap. Hand-tighten into place.
  • Using a spanner or pliers, turn a further 180° to secure. Avoiding over-tightening.
  • Do not turn the water supply on. The Dishwasher must be powered on for the flood protection feature to be enabled.
• Plug the product in.

SINK TRAP/WASTE TEE INSTALLATION

• Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to ‘Plumbing & electrical considerations’ for minimum install heights.
• Pull the hose through the drain hose support before threading the hose clamp onto the hose and fitting to the sink trap. Secure to trap using the clamp. Ensure the hose is routed straight to the trap.
  • Unplug or drill out the waste tee before securing the joiner to the sink trap or waste tee.
• Ensure the rubber washer is fitted when connecting the inlet hose to the tap. Hand-tighten into place.
  • Using a spanner or pliers, turn a further 180° to secure. Avoiding over-tightening.
  • Do not turn water supply on. The Dishwasher must be powered on for the flood protection feature to be enabled.
• Plug product in.

INSTALLER CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Installation

• Check all parts are installed correctly and are secure.
• Ensure all packaging, tape, and rubberbands have been removed.
• Ensure all clearance gaps have been maintained.
• Ensure the Dishwasher is securely fastened to the cabinetry and door opens and closes freely with no resistance.
• Ensure the panel is fitted correctly to the Dishwasher
• Check the spray arm is in place, mounted correctly and rotates freely

Plumbing

• Ensure any knock-outs or plugs in the drain connection have been drilled out and the drain connection has been made.
• The drain hose joiner must not support the weight of excess hose material. Keep the drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the drain hose support.
• Ensure the inlet hose has supplied a rubber washer fitted, and that it is tightened.
• If connecting the drain hose to the sink trap, ensure the high loop is a minimum of 150mm higher than the drain hose joiner.
• Water softener models: adjust the water softener setting from the default setting to suit the water hardness of the area. Refer to your user guide.
• Ensure the water supply is turned off until the power is connected and turned on. The Dishwasher must be powered on for the flood protection feature to be enabled

Electrical

• Ensure all electrical tests have been conducted in accordance with local regulations.
• If the site is left without power after installation is complete, ensure the water supply is turned off to prevent flooding.

TEST OPERATION

1. Turn the power and water supply on and open the dishwasher.
2. Select RINSE
3. After the RINSE cycle has finished, ensure the dishwasher has run and drained correctly

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2023. All rights reserved.
The models shown in this guide may not be available in all markets and are subject to change at any time.
The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>