SECO-LARM U S A Inc IP 5MP 2.8-12mm Motorized Bullet Camera with WDR Installation Guide

SECO-LARM USA Inc IP 5MP 2.8-12mm Motorized Bullet Camera with WDR

Product Information

The IP 5MP 2.8~12mm Motorized Bullet Camera with WDR (EV-N1506-NW4WQ) is a smart camera that comes with AI functions. It features a SmartSens CMOS sensor and a resolution of 5MP (2880×1620). The camera supports H.265/H.264/MJPEG video encoding and has 2DNR DNR and 3DNR backlight options. It also has a motorized bullet camera and a viewing angle of 91/2 (242mm). The camera has an IP rating and can operate within given temperature and electrical limits. It comes with an RJ45 Ethernet jack, CVBS LAN, CVBS LAN RESET, ZOOM+, and reset button compartments.

Product Usage Instructions

1. Read the manual carefully before using the camera.

2. Ensure that the camera is used within the given temperature and electrical limits.

3. Avoid mounting the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.

4. Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the location where the camera is to be mounted.
   The 12VDC power supply wire is not required if using PoE.

5. Install and execute Device Config Tool on a computer connected to the same network as the camera.

6. Press the Search button. This will search for IP cameras connected to the same router on the network. A default IP address is 192.168.1.168.

7. Once the search is complete, click on the camera IP or type the IP address manually using Internet Explorer.

8. Adjust the camera angle and positioning by loosening the camera angle adjustment screw and mounting the arm adjustment screw. Rotate the camera and position the mounting arm in the desired position and retighten the screws.

9. If you face any issues with the camera, refer to the troubleshooting section in the manual.

Features

• 1/2.7″ 5MP SmartSens CMOS sensor

• 30FPS@ 5MP (2880×1620)

• 2.8~12mm Motorized lens

• Tri-stream encoding:
  H. 265, H.264, and MJPEG

• True Wide Dynamic Range (WDR)

• Digital Noise Reduction (3DNR)

• True Day & Night function with ICR module

• ICR Sensitivity adjustment

• Corridor mode

• IP66 Weatherproof

• IR Range 147′ (45m)

• Smart IRs adjust IR strength to conditions

• MicroSD slot (512GB max)

• PoE (IEEE802.3af), 12VDC

• ONVIF® Profile G, S, and T conformant

• Operating Temperature: -40°~131°F (-40°~55°C)

AI Functions

• Human and Vehicle Detection
• Perimeter Intrusion Detection
• Line Crossing Detection
• Stationary Object Detection
• Cross Counting
• Heat Map
• Crowd Density Detection
• Queue Length Detection
• Face Detection

For the full Web Administration manual, download from the camera’s product page on www.seco-larm.com.

Parts List

• 1x Camera
• 3x Mounting Screws
• 2x Hex Key
• 1x Manual
• 1x Mounting Template
• 1x Weatherproof Connector

Specifications

AI functions

| Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, Stationary Object Detection, Cross Counting, Heat Map, Crowd Density Detection,

Queue Length Detection, Face Detection

# of IR LEDs| 4pcs (850nm)
Lens| 2.8~12mm, Motorized
Viewing angle| 38°~134°
Minimum illumination| Color: 0.002 lux at F1.2 (AGC on) 3 Lux with IR on
F Stop| F1.8 (W)~3.3 (T)
Gamma correction| Auto
S/N ratio| 39dB
Gain control| Auto
White balance| Auto
Operating voltage| 12VDC, PoE (IEEE802.3af Class 0)
Current draw (IR Off)| 80mA max.
IP Rating| IP66
Operating temperature| -40°~131° F (-40°~55° C)
Dimensions| ø35/16” x 91/2” (ø84×242 mm)
Weight| 21.87-oz (620g)
On-board storage| Built-in memory card slot, Supports MicroSD/SDHC/SDXC up to 512GB

Overview

IMPORTANT NOTES

• Do not cut the DC jack or RJ45 jack as the warranty will be voided.
• Do not open the camera case, no user-serviceable parts.

Before Starting

1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
4. Do not point the camera at the sun. Heat could damage the camera, even when not in use.
5. Do not open or disassemble the camera. There are no field-serviceable parts inside.
6. Do not drop the camera or subject it to strong vibrations.

Installation

1. Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the location where the camera is to be mounted. The 12VDC power supply wire is not required if using PoE.

2. Install and Execute “Device Config Tool” on a computer connected to the same network as the camera.

3. Press the “Search” button. This will search for IP cameras connected to the same router on the network. It may take several seconds to complete. Default IP address is 192.168.1.168.

4. Once the search is complete, click on the camera IP or type the IP address manually using Internet Explorer.

5. IP Address : The camera may use Dynamic or Static IP addressing. An example of a typical static IP setting is as follows:
   IP Address: 192.168.0.10 (you can change the last column)
   Netmask: 255.255.255.0
   Gateway: 192.168.0.1
   DNS1/2: You can copy the PC’s network properties. This is for an internet environment.

6. Input “admin” for user ID and password. If this is the user’s first time logging into the camera, the user will be prompted for a new password.
   NOTE: If the password is unknown, hold the RESET button located on the camera for about 10 seconds and reload “Device Config Tool”.

7. In order to access the camera web interface, the user will be prompted to download and install the Active-X web plugin.

8. Once installed, the user will be able to view live camera video and modify necessary configurations.

Camera Angle and Positioning

To adjust the camera angle and positioning, loosen the camera angle adjustment screw and mounting arm adjustment screw. Rotate the camera and position the mounting arm in the desired position and retighten the screws.

Troubleshooting

• The screen is blank
  • Check that the camera is powered up.
  • Check that the power supply’s polarity is correct.
  • Check that the monitor is powered up.
  • Check that the video cable connecting the camera to the monitor is connected properly.
• The screen image is dim
  • Clean the lens using a soft, clean cloth.
  • Check that the light source is adequate.
• The screen image has poor contrast
  • Adjust the monitor’s contrast knob.
  • Change the position of the camera.
• The screen image flickers
  • Change the position of the camera.
• The screen image is distorted
  • Change the position of the camera.
• The camera case is hot
  • Check that the correct power supply is in use.

FCC COMPLIANCE STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT

NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

California Proposition 65 Warning: These products may contain chemicals that are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if the damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason, SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

Website: www.seco-larm.com
Phone : 949-261-2999 | 800-662-0800
Email: sales@seco-larm.com

References

• La Armería de Madrid - fabricantes de armas y rifles
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>