LiFE WindPro Stand 65 Industrial Stand Fan User Manual

LiFE WindPro Stand 65 Industrial Stand Fan

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

Read the operating instructions carefully before putting the appliance into operation and keep the instructions, the receipt, and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions.

USER MANUAL SYMBOLS

Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine

WARNING: This sign warns you of dangers to your health and indicates
possible injury risks.
CAUTION: This sign refers to possible hazards to the machine or other objects.

NOTE: This sign highlights tips and information

SAFETY INSTRUCTIONS

1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. Make sure the fan is disconnected from the power supply before removing the protective grills.
4. Use the fan only for purposes described in the instruction manual.
5. Always use on dry, level surfaces.
6. To protect against electrical shock, do not immerse the fan, plug, or cord in water or any other liquid or spray with liquids.
7. The fan should not be placed near heat sources such as radiators, electric hobs or direct sunlight.
8. The fan should not be placed near places with water, such as sinks, bathrooms, swimming pools, etc.
9. Do not use the appliance in areas with flammable materials and gases, or in an environment with a lot of dust, air or steam.
10. Before using the fan, make sure that the voltage in your mains is the same as that indicated on the label of the appliance.
11. Unplug from the electrical outlet when not in use, when moving the fan from one location to another, before putting on or taking off parts, and before clearing.
12. Do not operate the appliance without supervision. If you leave the room, you should always turn the appliance off.
13. The protective grills are to prevent direct access to moving parts when the fan is in use Avoid contact with any moving parts.
14. To avoid injury, do not insert your fingers between the grilles when the appliance is plugged in or when it is turned on.
15. Do not move the fan while it is running. Disconnect the fan and wait until the fan blades stop completely.
16. Do not place clothes or other objects on the fan.
17. Do not use the appliance near curtains.
18. Check all parts of the appliance before using it. If there is any defect do not use the appliance and contact the manufacturer.
19. Do not operate any appliance, with a damaged cord plug after the appliance malfunctions, or has been dropped damaged in any manner.
20. Make sure the power cord is easily accessible at all times.
21. The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
22. Do not use the appliance before assembling it.
23. To disconnect from the electrical supply, grip the plug and pull from the wall outlet. Do not pull on the cord.
24. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard.
25. If you use the appliance outdoors and there is a need to use an extension cable, use a cable extension suitable for outdoor use in order to avoid fire and electric shock.
26. In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene, etc.) out of their reach.

CAUTION: Do not allow small children to play with the foil. There is a danger of suffocation!

BATTERY SAFETY INSTRUCTIONS (OF REMOTE CONTROL)

1. Different battery types or new and used batteries must not be used together.
2. Batteries can leak and lose battery acid. If the remote control is not used for a long period of time, remove the batteries.

PARTS IDENTIFICATION

1. Front grille
2. Fan blades
3. Motor
4. Tilt angle adjustment
5. Support and
6. Height regulator
7. Controller
8. Base
9. Remote control

REMOTE CONTROL

1. ON / OFF button
2. Nab.Jral wind mode selection button
3. Timer button
4. Oscillation button
5. Speed selection button

CONTROLLER

1. indicator lights (fan operating speed)
2. indicator light (natural wind simulation function)
3. Timer function indicator lights
4. Swlng mode selection button
5. limer selection button
6. Fan speed selection button
7. ON/OFF button

ASSEMBLY

1. Place the upright support shaft in the base.

2. Then secure the upright support shaft by turning the nut clockwise to the bottom of the base using the base washer as well.

3. Remove the Inner tube by pulling It out, then Install the ring.

4. Place the inner tube in place and secure it by screwing the three saws as shown in the image below.

5. Loosen the lock adjuster located on the small motor shaft, then align the small motor shaft with the slot on the inner tube. Secure the motor shaft to the pipe using the long bolt and washer.
   CAUTION: Make sure the motor is properly lod<ed in place and there is no risk of it slipping out of use.

6. Place the rear protective mesh on the front of the motor and align it. Then Insert the 4 saws and screw until It locks Into place.

7. Rotate the fan motor shaft until the flat surface on the shaft is at the 12mm position.

8. Install the Impeller onto the motor shaft. Align the mounting hole In the fan Impeller with the notch (flat part) on the motor shaft, and sea. ire with the mounting saw.

9. open the locking clips of the front protective mesh and unscrew the screw located at the bottom
   of it. Then align the upper locking clip of the front guard mesh with the center top of the rear guard mesh. Cose the side and bottom locking clips. Then screw in the screw at the bottom to complete the joint and sewer.

CAUTION

• Never operate the device if the protective mesh is not fully assembled.
• Make sure the fan is fully assembled (and that the protective meshes are in place and secured) before switching on the device.

OPERATING IN5TRUCTIONS

1. Before connecting the appliance, make sure that the voltage of your appliance corresponds exactly to the voltage at the mains.
2. Press the ON/ OFF button to tum on the fan. The fan will enter NORMAL mode. To deactivate the fan, press the ON/ OFF button.
   • The fan has 4 operating speeds:
   • Low (L)
   • Medium (M)
   • High (H)
   • Very high (H +)
   • You can select the desired operating speed by pressing the speed selector button on the remote control.

NATURAL WIND MODE

The fan has a natural wind simulation mode. Follow the following steps ID select it:

1. Tum on the fan by pressing the ON/ OFF button.

2. Select the desired operating speed (Medium to Very High)
   NOTE: This feature c.annot be activated at low speed.

3. Select the natural wind simulation function by pressing the Natural button on the remote control.

TIMER
The timer can be set ID switch the fan off at a time that you can program. Press the TIMER button to start setting the timer, then select the desired time (up to 7 hours) by pressing the time selection key on the remote control. With each press of the button, the time setting Increases by one hour e.g. If you press the button three times, the fan will run for three hours. When the tan stops running and shuts off, the previous timer setting will be lost.

SELECTION OF FAN INCLINATION

Follow these steps to select the desired tilt angle

1. Loosen the motor mount post nut and mounting screw.
2. Select the desired fan tilt angle and secure by tightening the nut and screwing the fixing screw.

CAUTION: Make sure it is properly secured and firmly in place before operating the device.

OSCILlATION MODE

To start and stop the oscillation mode of the fan, press the SWING button on the remote control. Press again ID bJrn off the feature.

NOTE: All fan functions can be selected either from the remote control or by pressing the buttons on the motor controller and the com.!Sponding indicator lights will illuminate accordingly.

CLEANING AND MAINTENANCE

Follow these Instructions to correctly and safely care for your fan.

1. Always disconnect the fan from the power supply before cleaning or assembling.

2. Do not Immerse or pour water directly onto the appliance. Risk of electric shock and fire!

3. Do not allow water to drip on or into the fan motor housing.
   CAUTION: Clean the surface with a damp, soft cloth. Do not use wire brushes or other sharp objects.

4. Do not use hard, abrasive or corrosive detergents or solvents to clean the appliance and any of the following as a cleaner: benzene, diluents or benzene.

FAN STORAGE

Your fan can be stored partially disassembled or reassembled.

1. Always disconnect the device from the power supply before storing the device.
2. Make sure the appliance is cold and dry before storage.
3. Always store the device away from children.
4. Always store the device in a safe and clean place. For the best protection of the device, store it in its original packaging.

Ionias Kalochori, 570 09 Thessaloniki, Greece, TEL. +30 2310 700.777 e-mail: info@sun.gr – www.life.gr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>