LAVEX JANITORIAL B-1500-FP Electric Burnisher Instruction Manual
- June 9, 2024
- LAVEX JANITORIAL
Table of Contents
Electric Burnisher
ELECTRICAL RATING
| V| A| Hz
---|---|---|---
b-1500-FP| 120| 15| 60
B-1500-FC| 120| 15| 60
OPERATION INSTRUCTIONS MANUAL DE OPERACION
CONGRATULATIONS!
YOU HAVE JUST ACQUIRED ALAVEX JANITORIAL BURNISHER, PLEASE READ THIS MANUAL
CAREFULLY BEFORE CONNECTING YOUR BURNISHER.
KEEP THIS MANUAL ON HAND FOR FURTHER REFERENCES. MODELS / MODELOS B-1500-FP,
B-1500-FC.
GENERAL DIAGRAM
No. PART LIST
1 Circuit breaker
2 Switch lock
3 Cover
4 Handle grip
5 Starting switch
6 Handle tube
7 Lever assembly
8 Cable support
9 Line cord
10 Female motor cord
11 Motor cord
12 Pressure adjusting knob
13 Clamp
14 Wheels
15 Motor cover
16 Chassis
17 Plate
18 Security nut
19 Box switch insert
20 Dust Control compartment (only on Dust Control models) 
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING AN ELECTRICAL BURNISHER, BASIC PRECAUTIONS SHOULD BE FOLLOWED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING THE MACHINE.
SAVE THESE INSTRUCTIONS FOR FURTHER REFERENCE
To reduce risk of fire, electric shock or injury:
-
“WARNING OF POTENTIAL INJURY”.
The burnisher contains moving parts, be sure to unplug machine servicing to reduce the risk of injury. -
Do not put any objects into openings.
-
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
-
Make sure the machine is in operating position.
-
Do not leave machine unattended when plugged in. Unplug the electrical cord when not in use or before servicing.
-
Use only as described in this manual. Use only manufacturer’s recommended attachments.
-
Do not use with damaged cord or plug. If machine is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, retum it to service center before using.
-
Do not pull or carry by cord, use cord as handle, close a door on cord, or pull a cord around sharp edges or corners.
-
Do not run machine over cord. Keep cord away from heated surfaces.
-
Do not use extension cords or outlets with inadequate current carrying capacity.
-
Verify if local voltage is 120 V~
THESE MODELS ARE GROUNDED, CONNECT TO A PROPERLY GROUNDED OUTLET ONLY, SEE GROUNDING INSTRUCTIONS.
GROUNDING INSTRUCTIONS
General. This floor-finishing machine shall be grounded while in use to
protect the operator from electric shock. The machine is provided with a
three-conductor cord and a three-contact grounding type attachment plug to fit
the proper grounding type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Never connect this wire to other
than the grounding pin of the attachment plug.
WARNING Improper connection of the equipment-grounding conductor can
result in a risk of electric shack. Check with a qualified electrician or
service person if you are in doubt of the outlet been grounded and if so have
a proper outlet installed.
This machine is for use on a nominal 120 V~ circuit and has a grounding plug
than resembles the plug illustrated in sketch A. Make sure that the machine is
connected to an outlet having the same configuration as the plug. No adapter
should be used with this machine.
Note: In Canada, the use of a temporary adaptor is not permitted by the
Canadian Electrical Code.
Warning: The power cord on this product contains lead, a chemical known
to the State of California to cause bisth defects or other reproductive harm.
WASH HANDS AFTER HANDLING.
HOW TO ASSEMBLE THE HANDLE TUBE
Model: B-1500 FP and B-1500 FC
- Before assembling the handle tube (6), make sure the handle clamp (13) is positioned with the hole in the tube facing the motor (see Fig A).
- Slide the handle tube (6) through the handle damp (13), hold the yoke (20) vertical and insert the tube over the yoke (see Fig A).
- Turn the handle tube so the box switch insert faces the motor, align the holes on the tube and the yoke, place the two screws in the holes with the heads towards the motor (see Fig B).
- Place the safety nuts (23) on the screws, with the flat part facing the screw, tum them manually until they get hard, then hold the head with one 7/16 wrench and tight the nut with the other wrench as far as it can go (See Fig B).
- Move the handle release lever(7) down on the lock position and turn the pressure-adjusting knob (12) as far as it goes (see Fig C).
- Place the handle release lever (7) up on the release position and tighten the pressure adjusting knob 1/4 more.
- Place the handle lever (7) down again, and try tilting the machine over the rear wheels pulling down the handle, if the handle damp (13) slips over the tube, move the handle lever (7) up to the release position, and turn the adjusting knob 1/4 more.
- Repeat step No.7 until the handle clamp does not slips when trying to tilt the machine.
- Connect the motor cord (11) to the female motor cord (10).
DUST CONTROL MODEL: B-1500 FC
THIS MODEL INCLUDES A DUST CONTROL SYSTEM THAT COLLECTS FLOOR FINISH DUST INTO
A FILTER BAG, MAINTAINING HEALTHIER INDOOR AIR QUALITY.
HOW TO INSTALL PADS
- Make sure the machine is unplugged.
- Lower the unit until the box switch is on the ground.
- This machine includes a plastic tube located at the lower part of the plate that avoids brush skirt to get damaged during transportation. Remove this piece by pulling it outwards (Fig. 3).
- Place the pad in position and secure it by using the center plate (included). Tum the center plate clockwise until it is tight.
HOW TO REPLACE FILTER BAG
-
Make sure machine is unplugged.
-
Open the Burnisher’s front compartment (Fig.4).
a. Grasp the bag and pull it carefully from the connector.
b. Place the new bag around the connector and close the front compartment. -
Change the filter bag at least every 6 months or when the bag is about half of its capacity.
STORAGE
- To avoid brush skirt damage, while the machine is not in use lean back on its 4 wheels, lifting the plate from the floor.
HOW TO USE YOUR MACHINE
ALWAYS UNPLUG THE MACHINE BEFORE PLACING THE DRIVER OR PADS
HOW TO INSTALL THE PAD DRIVER
- Make sure machine is unplugged (9).
- Lower the unit until the box switch (3) is on the ground.
- Unscrew the center plate (17), located at the lower part of the plate, counter clockwise. Insert center plate and turn clockwise until it is tight.
HOW TO START YOUR MACHINE
- . Place the appropriate pad and connect the line cord into a grounded outlet.
- Place the machine over the rear wheels. Turn on the starting switch and push the switch lock, with this the motor start working. Wait 5 seconds and place pad on the floor.
- Some models are provided with an overload protector that will work if the pad is overloaded. If that occurs, wait 30 seconds, approximately, and push the red button, you will hear a click. After that you can turn on the machine as described in point 2.
OPERATING TIPS
- It is convenient that the operator start at the position closest to the current outlet and move outward as far as the line cord will go. Then return to the original point.
- To stop the machine just release the handle levers.
- Remove driver & pads before storing.
- To go up or down stairs use the rear wheels.
- Due to it’s high speed never use on wet floors or with pads larger than 20″ in diameter.
- Use the appropriate discs: the darker discs are more abrasive. The correct disc will give you the best results according to the floor condition and type.
- Model: B-1500 FP N and B-1500 FC N. It is important to lower the handle tube to a comfortable height to operator. This machine should operate with the handle free. Do not fix it with the handle lever (7).
CAUTION: DO NOT USE THIS MACHINE WITH THE HANDLE TUBE IN VERTICAL
POSITION, YOU WILL NOT CONTROL It
(-WARRANTY This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state. This product is
warranted against malfunctions and defects in material and workmanship for a
period of 1 (one) year and 5 (five) years on motor and transmission. THIS
WARRANTY SHALL NOT APPLY to any products or parts there of which have been
damaged by tampering, misuse or abuse or which have been altered or repaired
by an unauthorized person or service center. THIS WARRANTY SHALL NOT APPLY to
brushes, since length of their life depends upon the amount of use. FOR
REPAIR, the inoperative machine must be delivered with shipping and delivery
charges prepaid, together with satisfactory evidence of the purchase date to
the dealer from whom it was purchased Lavex will either repair or replace, at
its election, all defective machines during the warranty period. THE FOREGOING
OBLIGATIONS ARE IN LIEU OF ALL OBLIGATIONS AND LIABILITIES INCLUDING
NEGLIGENCE AND STATE LAVEX’S ENTIRE AND EXCLUSIVELY LIABILTIY AND PURHCASER’S
EXCLUSIVE REMEDY LAVEX WILL IN NO EVENT BE LIABLE FOR ANY DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES WHATSOEVER, AND LAVEX
LIABILITY UNDER NO CIRCUMSTANCES WILL EXCEED THE CONTRACT PRICE FOR THE GOODS
OR PARTS FOR WHICH LIABILITY IS CLAIMED.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to
you.
Product / …………………………………….Brand / ………..Model I Serial………… Number! ……………Distributor /…………………….. Address………………….
Delivery Date Signature
Modelos: B-1500-FP, B-1500-FC.
Manufactured for: Fabricado para: Lavex Janitorial 2205 Old Philadelphia Pike
Lancaster,
PA 17602 P 717-392-7550
www.webstaurantstore.com
MADE IN MEXICO / HECHO EN MEXICO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>