RAYDEM X1 Native 1080P LED Full HD Projector User Manual
- June 10, 2024
- Raydem
Table of Contents
- IMPORTANT SAFEGUARDS
- ACCESSORIES LIST
- PROJECTOR OVERVIEW
- STANDARD SETTING
- HOW TO INSTALL THE PROJECTOR ON THE CEILING:
- SWITCHING MACHINE OPERATION
- FOCUS / KEYSTONE CORRECTION / ZOOM
- SOURCE SETTINGS
- PROJECTION SETTINGS
- IOS CAST–WIRELESS CONNECTION
- IOS CABLE
- MIRACAST-WIRELESS CONNECTION
- SPECIFICATIONS
- MULTIMEDIA SUPPORTED FORMATS
- WARRANTY INFORMATION
- WHAT IS NOT COVERED
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PROJECTOR
NATIVE 1080P LED FULL HD
FHD
1080P
User Manual
IMPORTANT SAFEGUARDS
- Please read the manual carefully before operating projector. To ensure stable power supply, please use standard power cord.
- Please use the power supply and cable indicated on the rating label. The projector should be kept away from cloth, sofas and anything that may block the ventilation scoop. Please keep the unit away from flammable and explosive materials.
- Please do not disassemble the unit by yourself as this will invalidate the warranty service. To protect your eyes, do not stare directly at the lens when the projector is on. The projector must be kept away from water and any other liquids.
- To prevent electric shock, please keep the projector out of the rain and away from moisture. It is recommended to turn off the projector after 6 hours of operation (or when not in use). Please use the original foam and other cushioning materials when transporting the projector.
- If the projector does not work, please contact the authorized service agent.
ACCESSORIES LIST
AV Signal Cable ×1
Remote Control ×1
Power Cabel ×1
User Manual ×1
Adjustable Foot ×1
HD Cable ×1
PROJECTOR OVERVIEW
STANDARD SETTING
Refer to the data in the table below to place the projector away from the
projection screen according to the preset graphic size. When installing, place
the projector on a solid, stable countertop . The airframe should be well
ventilated. Do not cover or block the vents.
There should be no obstructions within 30cm of the vents.
( Tip: The shortest projection distance of the projector is 1.8 meters)
Aspect Ratio | 16:09 |
---|---|
Picture Size (inch) | Projection Distance (m) |
60 | 1.8 |
70 | 2.17 |
100 | 3.11 |
120 | 3.73 |
200 | 6.19 |
Note: The above data is for reference only, please refer to the physical measurement.
HOW TO INSTALL THE PROJECTOR ON THE CEILING:
-
Determine the best throw distance and ratio for your projector.
Once you evaluate the room and decide where it makes the most sense to mount the projector. You can start to install the projector mount. -
Prepare for a mount and tools(not included) that suit the projector depending upon your ceiling type.
-
Turn the projector upside down. Remove the rubber feet from the bottom of the projector and attach the mount to the projector.
Ensure that the entire mount is attached to the projector before securing it to the ceiling. -
Secure the projector and install the mount to your ceiling.
-
Attach the cables to the projector.
-
Adjust the settings to fine tune the image.
Warning:
– Before installing, ensure the mount can withstand the weight of the
projector, ceiling mounting bracket and other components to prevent unit from
dropping.
– Raydem will not be liable for any accidents occurring from the unit dropping
due to improper mounting, etc.
SWITCHING MACHINE OPERATION
Power On:
Step1: Press the power button on the body or the power button on the remote
control, the indicator light will turn blue.
Step2: After 2 seconds, the projector starts to start, the image ppears on the
screen, and the unit enters the normal working state.
Step3: If the projector is newly installed, the image may be blurred or
trapezoidal distortion when it is turned on for the first time. Please refer
to the “Focus/Keystone Correction” section for calibration.
Step4: After the image is adjusted clearly, it can be viewed normally.
Power Off:
Step1: In the working state, press the power button of the body or the power
button on the remote control to switch the projector to the shutdown state.
Step2: After the projector enters into the shutdown state,the indicator light
will change from blue to red.
FOCUS / KEYSTONE CORRECTION / ZOOM
Image Focusing
Place the projector lens perpendicularly to the projection screen or curtain
wall,and press the F+ and F- focus buttons on the remote control until the
image is clear,that means the image focusing is finished.
During the focusing process, you can play the programs or pick up the product
menu images to match the focusing adjustment.
Keystone Correction
Please turn on the keystone correction on the main interface, and adjust the
image through the horizontal, vertical or four-point keystone correction
function until the image is displayed normally.
Zoom
Please zoom the picture 80%-100% by zoom function.
Cast Mode: Front, Rear Ceiling
Note: As the product system is updated from time to time, the specific
operation content is based on the actual situation.
SOURCE SETTINGS
Select the appropriate input source (HD, AV, USB-Movie-Music-Photo-Office
Documents) in the menu (as shown in the Figure on the following) using the
remote control or
pressing the keys on the operational panel of the projector.
Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.
PROJECTION SETTINGS
-
From Home Screen, select ‘Settings’ to change projection settings.
-
“Network Settings”, “Bluetooth Settings”, “Bluetooth Speaker”, “Language Settings”, “Restore Factory Settings”, “Focus Settings” can be set.“System Info” can be obtained. Press the ” ∧” and ” ∨” on the remote control to select the range of settings.
-
Network Setting
Select your WIFI to make sure that the projector connect to the same wifi to your phone. Press the ” ∧” and ” ∨” on the operation panel to select the correct WiFi. Press the “OK” key to enter the password page. -
Bluetooth Speaker
Select the Bluetooth speaker function, then use a device such as a mobile phone to turn on Bluetooth, search for the Bluetooth name of the projector to connect (the projector will enter the black screen energy-saving mode after entering the Bluetooth speaker mode, if you want to exit, click the back button on the remote control) -
Restore Factory
When you choose to restore the factory settings, you can restore the projector’s system to the factory settings, and it can be used after restarting. -
Language Setting
There are English, Deutsch, France, Chinese, Italian, Espanol and Japanese. etc for your choice.
Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.
IOS CAST–WIRELESS CONNECTION
Step1: Select iOS Cast on the main interface,then select Wireless Cast.
Step2: The iOS device and the projector must be connected to the same network.
Step3: Select Screen Mirroring on the control center of the iOS device.Then
select PROJECTOR-X1-XXXXXX from the searching results to connect.
MIRROR YOUR IPHONE, IPAD OR IPOD TOUCH
Make sure that your iOS device is connected to the same network as your
projector.
1. On your iOS device, open Control Center and tap screen Mirroring.| 2.
Looking for devices that can be mirrored on.| 3. Select PROJECTOR-X1-XXXXXX
from the list
---|---|---
| |
IOS CABLE
Step 1: Select iOS Cable from IOS Cast in the main interface.
Step2: Use the data cable to connect the iOS device and the projector (through
the USB port of the projector).
Step3: Click Trust in the pop-up window of the iOS device.
Step4: Enter the iOS device password.
Note: If still cannot connect with projector afer clicking Trust, can try
to use the original data cable to reconnect.
iOS Cable
1. Connect the lightning connector to the phone. Connect the other end to the
projector| 2. Click “Trust” the window that pops up
on the phone.| 3. Enter device password.
---|---|---
| |
MIRACAST-WIRELESS CONNECTION
Step 1: Select Miracast on the main interface.
Step 2: Turn on the Wireless Display function of the Android device.
Note: Different Android devices have different names and opening methods
for the Wireless Display function. For details, please refer to the manual of
the Android device you are using.
Step 3: Select the corresponding projector device name.
Miracast
To connect Android Mobile/Pad Device with Projetor Based on WiFi-Display
Techenology
- On your Android Mobile/Pad, open the settings menu.
- Access your display settings or screen-mirroring.
- Select your Miracast receiver: PROJECTOR-X1
Miracast
To connect Android Mobile/Pad Device with Projetor Based on WiFi-Display
Techenology
- On your Android Mobile/Pad, open the settings menu.
- Access your display settings or screen-mirroring.
- Select your Miracast receiver: PROJECTOR-X1
Waiting for connection…
Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.
SPECIFICATIONS
Model | X1 |
---|---|
Lamp | LED |
Image System | LCD |
Language | English, total 26 Languages |
Resolution | 1920×1080p |
Input Voltage | 110-250V~ |
Weight | 2.36KG |
Working Temp | 0-35°C |
Input Port | HDMI / USB / AV |
Output Port | Headphone |
Aspect Ratio | 16:9 / 4:3 |
Size | 243mm248mm112mm |
Operation Mode | Remote Control |
MULTIMEDIA SUPPORTED FORMATS
Image Format | JPG,PNG,BMP ,GIF |
---|---|
Video Format | AVI ,MKV ,MP4 ,MOV,MPG ,VOB |
Audio Format | MP3 、AAC、WAV、FLAC、WMA |
File Format | EXCEL ,WORD,PPT,PDF,TXT |
WARRANTY INFORMATION
TWO YEAR NON-TRANSFERRABLE LIMITED WARRANTY
To provide customers with quality shopping and user experience, we guarantee
to replace or issue a refund or provide acceptable solutions for any defective
products (as customers prefer) from the date of purchase up to 2 years.
Proof of purchase must be provided (Amazon order number or receipt) when
making a claim to our customer support center.
Warranty registration may be requested within a month from the date of
purchase, by sending your Amazon order number to the mailbox:
support@aborderproducts.com.
The warranty is not transferable. We only provide warranty services to buyers
who purchased from our Amazon store and possess the purchase proof, and not to
any other purchaser or subsequent owner.
Price matching policy is not applicable. No price difference refund.
Sellers are the responsible party. Amazon allows different sellers to sell the
same product, so please confirm the seller by checking the order details
before contacting us.
WHAT IS COVERED
- Received defective or used (proof needed) products.
- Received with missing parts.
- Defective item under proper use.
WHAT IS NOT COVERED
MANUFACTURER SUPPORT
- Purchased from non-Amazon channel or other physical stores.
- Gift without proof of purchase.
- Tampering/ abnormal use/ accidental damage or commercial use.
- Replacements and parts.
- Installation fee/ labor fee.
MAKING A CLAIM
If you have any problems when using our products, you can choose any of the
methods to reach out to us.
Toll free: 1-888-281-8150 (Mon-Fri,
10am-6pm EST)
Email: support@aborderproducts.com
(24/7)
30 days free Return & Replacement
2-Year Product Warranty
Gifted parts, replacements, consumable products are not covered by the 2-year
warranty.
Manufacturer’s warranties may not apply in all cases, depending on factors
such as use of the product, where the product was purchased, or who you
purchased the product from.
Please review the warranty carefully, and contact the manufacturer if you have
any questions.
Warning:
Warning: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference. (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However. there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, this equipment
should be installed and operated with minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>