BOSCH 150 Advanced Aquatak High Pressure Washer Instruction Manual

Original instructions

AdvancedAquatak
150 | 160

Safety Notes Explanation of symbols

General hazard safety alert.
** Never direct the water jet at people, animals, the unit or electric components.
Warning:** High pressure jets can be dangerous if subject to misuse.

According to the applicable regulations, the appliance must never be used on the drinking water network without a system separator. Use a separator as per IEC 61770 Type BA.
Water flowing though a system separator is considered not drinkable.

The AdvancedAquatak 150 is intended for use only in premises having a service current capacity ≥100 A per phase, supplied from a distribution network having a nominal voltage of 230 V. If in doubt please contact your Supply Authority.

Safety Notes for pressure washer
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

The warning and information signs attached to the unit provide important information for safe operation.
Apart from the information in the operating instructions comply with the general safety regulations and regulations for the prevention of accidents.

Connecting to the mains

• The voltage indicated on the rating plate must correspond to the voltage of the power source.
• We recommend that this equipment is only connected into a socket which is protected by a circuit-breaker that would be actuated by a 30 mA residual current.
• Remove the plug from socket whenever the machine is left unattended for any period.
• The electric supply installation should comply with IEC 60364-1.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• If the plug is damaged, pay attention to the following:
• Plugs and sockets situated near the work site or outdoors should be to class IP 55 of BS 5490 to provide adequate protection against ingress of water, etc. and cable  entries require effective sealing. Rubber shrouds should be provided over cable glands. Drip-proof (class IP X2 of BS 5490) plugs and sockets to BS 4343 are suitable for use indoors where the plug is away from the water spray area where the appliance is in use.
• Never touch the mains plug with wet hands.
• Do not pull plug while operating the device.
• Do not run over, crush or pull the power supply cord or extension cord, otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.
• Do not use the unit, if the power supply cord or important parts, e. g. high-pressure hose, power gun or safety devices are damaged.
• Warning: Inadequate extension cords can be dangerous.
• If an extension cord is used, the plug and socket must be of watertight construction. The extension cord must have a cross section in accordance with the operating instructions and be protected against splashed water. The connection must not be in water.
• When replacing plugs on the power supply cable or extension lead the spray water guard and mechanical stability must remain intact.

Water connection

• Comply with the regulations of your water supply company.
• All connecting hoses must have properly sealed joints.
• Make sure that the supply hose is at least 12.7 mm (1/2″) in diameter and is reinforced.
• The appliance should never be used on the drinking water supply without a back flow valve. Water which has passed the back flow valve is regarded as undrinkable.
• The high-pressure hose must not be damaged (danger of bursting). A damaged high-pressure hose must be replaced immediately. Only use hoses and connections  recommended by the manufacturer.
• High-pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer.
• Only clean or filtered water should be used for intake.

Application

• Before use, check that the unit and operating equipment are in perfect condition and are safe to operate. Do not use the unit if it is not in perfect condition.
• Do not direct the jet against yourself or others in order to clean clothes or footwear.
• Do not use solvent-containing liquids, undiluted acids, acetone or solvents! This includes petrol, paint thinners, heating oil. The sprayed vapour is highly flammable,  explosive and toxic.
• The appropriate safety regulations must be observed when using the unit in dangerous areas (e. g. petrol stations). It is forbidden to operate the unit in potentially explosive locations.
• The unit must be placed on a solid base.
• Take care if using the machine in a confined space ensuring that there is adequate ventilation. Ensure that all vehicles are switched off at all times whilst cleaning.
• Operation of this machine requires both hands to be used at all times. Do not operate from a ladder. Take care when using the machine on balconies or other raised areas ensuring that you can see any edges at all times.
• Only use detergents recommended by the manufacturer. Comply with the application, disposal and warning instructions of the detergent manufacturers.
• All current-conducting components in the working area must be protected against splashed water.
• The gun trigger must not be jammed in position “ON” during operation.
• Wear suitable protective clothing to protect against splashing from some parts. Do not use the appliance within the range of persons unless they also wear protective clothing.
• If necessary wear personal protective equipment (PPE) e. g. safety goggles, breathing protection etc to protect against water, particles and/or aerosols sprayed back from parts.
• High pressure may cause objects to rebound. If necessary wear suitable personnel protective equipment such as safety goggles.
• Vehicle tyres/tyre valves may only be cleaned from a minimum distance of 30 cm, otherwise the vehicle tyre/ tyre valve could be damaged by the high-pressure jet. The first indication of this is a discoloration of the tyre. Damaged vehicle tyres/tyre valves can be extremely dangerous.
• Materials containing asbestos and other materials which contain substances which are hazardous to your health must not be sprayed.
• Detergents must not be used undiluted. The products are safe to use as they contain no acids, alkalis or substances which are detrimental to the environment. We recommend that the detergents are kept out of the reach of children. If detergent comes into contact with the eyes, wash immediately with plenty of water and if swallowed contact a doctor immediately.
• Never use the pressure washer without the filter or with a dirty or damaged filter. Using the pressure washer without a filter or with a dirty or damaged filter may invalidate the warranty.
• Metal parts may become hot after prolonged usage, if necessary wear protective gloves.
• Avoid high pressure washing in bad weather conditions especially when there is a risk of lightning.

Operation

• The operator must use the unit in accordance with the regulations. He/she must take local conditions into account and be aware of other people, especially children, when operating the unit.
• The unit may only be used by authorised persons who have received training or have demonstrated their ability to operate the unit. The unit must not be operated by children or juveniles (danger of accidents due to incorrect use of the unit).
• Never allow children, persons with physical, sensory or mental limitations or a lack of experience and/or knowledge and/or people unfamiliar with these instructions to use the garden tool. Local regulations may restrict the age of the operator.
• Children should be supervised to ensure that they do not play with the machine.
• The unit must never be left unsupervised while the unit is switched on.
• The water jet from the high-pressure nozzle produces a recoil on the gun. You should therefore hold the gun and spray lance firmly with both hands.
• Never use a roto nozzle or pencil jet to clean motor vehicles.

Transport

• Switch off the motor and secure the unit before transporting.

Maintenance

• Switch off the unit prior to all cleaning and maintenance work and before replacing components. Pull out the mains plug if the unit is mains-operated.
• Repairs may only be carried out by authorised Bosch Service Centres.

Accessories and spare parts

• Accessories and spare parts which have been approved by Bosch must be used. Original accessories and spare parts guarantee that the unit can be operated safety and without any breakdowns.

Symbols

The following symbols are important for reading and understanding the operating instructions. Please take note of the symbols and their meaning. The correct interpretation
of the symbols will help you to use the machine in a better and safer manner.

Intended Use
The product is intended for cleaning areas and objects outside the house, tools, vehicles and boats, if the appropriate accessories and cleaning agents approved by Bosch are
used. Intended use is related to operation within 0°C and 40°C ambient temperature. This product should not be used for professional use.

Technical Data

The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary. Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.276 ohm. If in doubt please contact your Supply Authority.
Noise/Vibration Information

Sound emission values determined according to EN 60335-2-79.| 3 600 …| HA7 7..| HA7 8..
---|---|---|---
Typically the A-weighted noise levels of the product are:| 1| |
Sound pressure level| dB(A)| 77| 79
Sound power level| dB(A)| 88| 90
Uncertainty K| dB| 2| 2
Vibration total values ah (triax vector sum) and uncertainty K determined according to| | |
---|---|---|---
EN 60335-2-79:| | |
Vibration emission value ah| m/s²| 3.2| 2.9
Uncertainty K| m/s²| 1.0| 1.0

Mounting and Operation

269
Roto lance Connecting high pressure gun to lance Adjust water jet| 13| 270
Gun storage| 14| 271
Storage| 15| 271
Transport| 16| 272
Selecting Accessories| 17| 273

Starting
For Your Safety
Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.

The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Only use approved extension cables. Contact your Bosch Service Centre for
details.
If you want to use an extension cable when operating your high pressure washer, only the following cable dimensions should be used:
– 2.5 mm²
– max length 25 m

Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch Service Centre.

WARNING! Inadequate extension cables can be dangerous. Extension cable, plug and socket must be of watertight construction and intended for outdoor use.

Cable connections should be kept dry and off the ground.
For increased electrical safety use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Always check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch Service Centre.
For products not sold in GB:

WARNING: For your safety, it is required that the plug attached to the machine is connected with the extension cord. The coupling of the extension cord must be protected against splash water, be made of rubber or coated with rubber. The extension  cord must be used with a cable strain relief. To prevent damage to the appliance, do not allow
it to operate dry.

Products sold in GB only : Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent.
The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

Operation
Starting
Attach water supply hose (not supplied) to the mains water supply and machine. Connect the product to the mains supply ensuring that the mains switch is in the off position. Open water tap. Press the safety lock (back button on the gun handle) to release the trigger. Fully press the trigger  until there is a constant flow of water to clear the
air from the machine and water supply hose. Release trigger. Press the safety lock (front button on the gun handle). Turn button on main switch. Point the power gun downwards. Press the trigger safety lock to release the trigger. Fully press  thetrigger.

Autostop function
The machine is designed to switch off the motor when the trigger is released on the gun.

Working Advice

General
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the pressure washer by pulling the hose, this could cause the machine to become unstable and fall over. Do not kink
or drive a motor vehicle over the high pressure hose. Do not expose the highpressure hose to sharp edges or corners.

• Never use a roto nozzle or pencil jet to clean motor vehicles.

WARNING! The Patio Cleaners supplied are only intended to be used on flat surfaces! Do not attempt to use them on steps. Never attempt to touch the rotating nozzle  while operating the machine!

Working advice for cleaning with detergents

• Only use cleaning agents suitable specifically for high pressure washers.

We recommend that you use detergent sparingly for the sake of the environment. Observe the recommended dilution on the detergent label. The high-pressure foam nozzle supplied with this product includes a regulator to control detergent use. Adjust as required.

Recommended cleaning method
Step 1: Attach the fixed fan nozzle and remove the heavy dirt.
Step 2: Attach the foam bottle and spray on the detergent sparingly.
Step 3: Rinse off the loosened dirt and detergent with the fan nozzle.
Note: When cleaning a vertical surface spray off dirt/detergent from the bottom and work in an upwards direction. Rinse from  the top and work downwards.

Use with alternative water sources
This high-pressure washer will self prime and can draw water from water tanks and natural water sources. It’s IMPORTANT that the water is clean and the BOSCH inlet filter is clear and fitted to the machine.
Run the pressure washer with the gun disconnected until a steady flow of water appears from the high pressure hose. Stop if this has this has not been achieved within 25 seconds and check all the connections. Switch off and connect the gun, lance and nozzle to operate.
It is important to ensure that all hose and coupling connections are of good quality, air tight and that all washers are in good condition and correctly seated in place. Failure
to do so may affect the self priming performance.

Water Tanks with outlet connections
When connecting the pressure washer to a water tank with a suitable tap outlet, first connect the supply hose (not provided) to the tank outlet, open the tap to allow the water to displace all the air in the hose and then connect to the pressure washer.

Troubleshooting

the model
tag
Motor protector has activated| Allow to cool for 15 minutes
Fuses blow| Fuses incorrectly rated| Change to a mains supply higher than the pressure washer amp consumption
Motor starts but no pressure| Nozzle partly blocked| Clean nozzle
Motor “sounds” but fails to start| Insufficient power supply| Check that the voltage of the mains power supply
line is the same as that on the plate
Voltage loss due to use of extension
cable| Check characteristics of extension cable
Appliance not used for a long periodof time| Contact your Bosch Service Centre
Problems with TSS (Total Stop
System) device| Contact your Bosch Service Centre
Pressure pulsating| Air in the inlet water supply hose/pump| Allow pressure washer to run with open spray handle and  nozzleat low pressure until regular working  pressure is obtained
Inadequate water supply| Check that the water supply corresponds to specifications.
The minimum specification for the water  supply hose is 1/2″ or
13 mm diameter
Water filter blocked| Clean water filter
Water supply hoses squeezed| Straighten out kinked water supply hoses
High pressure hose too long| Remove high pressure extension hose. Retry (extension hose max. 7 m)
Pressure too low, but steady
Note: Several types of accessory will normally deliver a lower pressure| Nozzle worn| Change the nozzle
Start/stop valve worn| Activate trigger five times in quick succession
Motor starts up but with restricted or no working pressure| No water supply| Connect water supply
Water filter clogged up| Clean the water filter
Nozzle clogged up| Clean nozzle
The pressure washer starts irregularly by itself| Pump/power gun leaky| Contact your Bosch Service Centre
Water leaks from machine| Leaking pump| A slight water leak is permissible; in case of excessive
leak, contact Bosch Service Centre

Maintenance and Service

Maintenance

• Stop, remove plug from the power supply and disconnect from water supply.

Note: To ensure long and reliable service, carry out the following maintenance regularly. Regularly check for obvious defects such as loose fixings, and worn or damaged components. Check that  covers and guards are undamaged and correctly fitted. Carry out necessary maintenance or repairs before using. If the replacement of the supply cord is necessary, this has to be done  by Bosch or an authorized Bosch service agent in order to avoid a safety hazard.

After use/Storage
Turn the main switch off and operate the trigger to drain the water from the high pressure hose. Clean the exterior of the machine thoroughly using a soft brush or cloth. Do not use water, solvents or polishes. Remove all debris, especially from the ventilation slots. End of season storage: Drain water out of pump running motor for a few seconds.
Pull trigger to release all water. Do not place other objects on top of the machine. Store in a frost-free area. Ensure cables are not trapped when storing. Do not kink high pressure hose.

After-sales Service and Application Service
www.bosch-do-it.com
In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the machine.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au

Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za

KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com

Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za

Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: rbsa-hq.pts@za.bosch.com

Environmental Protection

Chemicals dangerous to the environment must not be allowed to enter the ground, ground water or ponds, streams, etc. For the use of cleaning agents, observe the instructions on the package and the prescribed concentration exactly.
For the cleaning of motor vehicles the local regulations should be observed: Do not allow oil sprayed off to enter into the ground water. Recycle raw materials instead of waste disposal.

Disposal
The pressure washer, accessories and packaging should be sorted for environmental-friendly recycling.
Do not dispose of pressure washers into household waste!
Only for EC countries:
**** According to the European directive 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national law, electrical and electronic equipment that are no longer usable must be collected separately and disposed of in an environmentally correct manner. Subject to change without notice.

EU Declaration of Conformity
Pressure washer
Article number
**** We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.

AdvancedAquatak 150
2000/14/EC: Measured sound power level 88 dB(A), uncertainty K =2 dB, guaranteed sound power level 90 dB(A); Conformity assessment procedure in accordance with
annex V. Product category: 27 AdvancedAquatak 160  2000/14/EC: Measured sound power level 90 dB(A), uncertainty K =2dB, guaranteed sound power level 92 dB(A); Conformity assessment procedure in accordance with annex V. Productcategory:  27 Technical fileat: *

• Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2,
  Stowmarket, Suffolk IP14 1EY, England

Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 01.01.2017

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-do-it.com

References

• Invented for life | Bosch Global
• The domain name bosch.mk is for sale
• dz.com
• Check out our sponsor - Spency.tv
• Location selection | Bosch DIY
• bosch-powertools.com.ua
• Bosch Elektrowerkzeuge | Bosch Elektrowerkzeuge
• Bosch Услуги | Электроинструменты Bosch
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Bosch Elektrowerkzeuge | Bosch Elektrowerkzeuge
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Elettroutensili Bosch | Elettroutensili Bosch
• Home | Bosch Power Tools
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Home | Bosch Power Tools
• Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
• Elektronarzędzia Bosch | Elektronarzędzia Bosch
• Bosch Услуги | Электроинструменты Bosch
• Elektrické náradie Bosch | Elektrické náradie Bosch
• Bosch România | Bosch în România
• Начало | Бош в България
• Invented for life | Bosch Global
• Home | Bosch in Australia
• Domovská stránka | Bosch Česká republika
• Innostavia tuotteita ja palveluita | Bosch Suomessa
• Дом | Қазақстандағы Bosch
• Strona główna | Bosch w Polsce
• Domov | Bosch Slovensko
• herramientasbosch.net
• Karcher Centar KELLER | Karcher Centar KELLER | Niš Srbi...

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>