Silverstar SS358XCE LED Stage Lighting User Manual

Silverstar SS358XCE LED Stage Lighting

PRODUCT

TECHNICAL SPECIFICATIONS

-20°C~45°C (SS358XCEM\SS342XCET)

Dimensions| 245X246X202mm
Weight| 4.8kg

Safety Notes

• This product must be installed by a qualified
• In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
• The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the

CAUTION!

• Make sure that the available voltage is not higher than stated on the rear
• Do not touch the power cables if your hands are
• The earth wire must always be connected to the Therefore it is essential to connect the yellow/green conductor to earth.
• Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time. The electric connection, repairs and servicing must be carried out by a qualified
• Always disconnect power input cable to completely remove power from unit when not in use or before cleaning or servicing the fixture.
• Do not switch the fixture on and off in short intervals as this would reduce the lamp’s
• Do not touch the device’s housing bare hands during its operation (housing becomes hot)! The surface of the product’s casing can reach up to 70° C (158° F) during operation. Avoid contact by persons and Do not install the product in a location where there is a risk of accidental contact. Allow the product to cool for at least 1O minutes before handling.
• For replacement use lamps and fuses of same type and rating
• Please protect the fixture and avoid destroy during transport and installation. If there is any damage to the coating, the shell may be
• When hanging lamps and lanterns, it is necessary to verify that facilities and hooks can bear at least 1O times the weight of lamps and
• Fix the safety rope at the correct holes only. Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly

The maximum ambient temperature 45°C must never be exceeded. Do not

operate the product if the ambient temperature (Ta) exceeds 45° C (115° F).

Electrical Warning

• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person

INSTALLATION

MOUNTING

UPRIGHT

• **** For overhead use, always install a safety cable that can hold at least 10 times the weight of the

• For overhead installation, the fixture must be always secured with a safety wire that can bear at least 10 times the weight of the fixture: Secure the fixture with a safety cable through the rear safety eye as shown

• Ensure that the structure (truss) to which you are attaching the fixture is secure

• POWER CONNECTIONS

• POWER Linking: 11 units@110V: 22 units@220V.

This product has an auto-ranging power supply that can work with an input voltage range of 100-240 VAC, 50/60 Hz

AC Plug

Data network requirements

• Connect the OMX512 controller to the units in series. A OMX 512 data link is required  in  order to control the fixture via OMX. The fixture has 3/5-pin XLR connectors for OMX data  input and
• Each unit has 13 OMX channels so the OMX Addresses should increase by increments of 1, (Nx1)+1, (Nx2)+1, (Nx3)+1…
• Any OMX address in the range from 001 to 512 may be

FUNCTIONS AND SETTINGS

DISPLAY OPERATION

• MENU: Used to access the menu or to return a previous menu option;
• ENTER: Used to select and store the current menu or confirm the current function value or option within a menu;
  • UP: Navigates downwards through the menu list and increases the numeric value when in a function;
  • DOWN: Navigates  upwards through the menu list and decreases the numeric  value when in a function;

STAT| RED| R.0-255| Combine [RED],[GREEN],[BLUE],[WHITE] to create an infinite range of colors(0-255). Set the value of the STROBE.
---|---|---|---
GREEN| G.0-255
BLUE| B.0-255
WHITE| W.0-255
STROBE| S.0-25
ADDR| 001-512 C default001 )| Set the OMX ADDRESS
RUN| OMX C default)| [DMX] Using the OMX 512 controller to control;[SLAVE] Master-Slave operation.
SLAVE
PERS| HSIC| Use the menu to select desired channel mode
SSP
TOUR (default)
TR16
AUTO| AT.1| 0-255| Selects automatic AUTO program and AUTO program speed.

Programs [CUSTOM 1] to [CUSTOM 2] are fully pre-programmed and can be edited in [EDIT) mode.

AT.2| 0-255
…| 0-255
AT10| 0-255
PR 1
PR2
EDIT| PR 1-2| SC 01-10| RED| R.0-255| Enter the [EDIT] mode to edit the custom programs [PROGRAM01) to [PROGRAM2].

Each custom program has 30 scenes that can be edited.

Fade transition time, time 0-255 unit is second, fade time setting should be less than time setting.

After editing the program, Play in AUTO.

GREEN| G.0-255
BLUE| B.0-255
WHITE| W.0-255
STROBE| S.0-25
TIME| R.0-255
FADE| G.0-255
UPLOAD| **| SEND| Select [UPLOAD] to upload the custom programs
SET| **| REST| **| REST| Restore factory settings
DIMM| DIM4 C default)| Dimming curves DIM1 (fast) to DIM4** (slow);
OFF
OMX

ERROR

| SAVE ( default)| Hold after loss of OMX signal
BLACK| Blackout after loss of OMX signal
PWM| 1200HZ ( default)| Sets the PWM frequency
2400HZ|
4000HZ|
6000HZ|
25000HZ|
OKEY| ON (default)| Locks  display   (passcode             is