Aryantra AY-PMD-950G Mixture Drill User Manual

June 10, 2024

Aryantra AY-PMD-950G Mixture Drill User Manual
Aryantra AY-PMD-950G Mixture Drill

Scan the QR Code to Dolwnlond
QR Code

Kisankraft App

Please read these operating instructions before using the tool for the first time and keep them with the tool at all times.

Safety Instructions

General Power Tool Safety Warnings

WARNING Read all safety warnings and al

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious Injury

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains operated (Corded) power tool or batteryoperated (cordless) Power tool.

Work area safety

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or

  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

  • Do not abuse the cord. Never use the cord for carrying, Pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.

  • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

  • If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shoc

Personal safety

  • Stay alert, watch what you are doing and use commonsense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, on-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
  • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
  • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power too may result in personal injury.
  • Do not overreach. Maintain proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  • If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dustrelated hazards.

Power tool use and care

  • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.


Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

  • Do no use the power tool with a damaged.
  • Do not touch the damaged cord and pull the plug from the outlet when the cord is damaged while working. Damaged cord increase the risk of an electric shock
  • Connect power tools that are used in the open via a Ground Fault Circuit interrupter (GFCI).
  • Wear hearing protection. Exposure to noise can cause hearing loss.
  • Use the auxiliary handle supplied with the power tool. Loss of control over the power tool can cause Personal injury.
  • Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to explosion. Penetrating a water line causes property damage or may cause an electric stock.
  • Hold the power tool only by the insulated gripping surfaces when performing an operation where the cutting tool may contact with a “live” wire will also, make exposed metal parts of the power tool “live” and shock the operator.

Before Use
Read all the safety warnings and all instructions

Intended Use.
The power tool is intended for Chiseling work in concrete, brick, masonry and asphalt as well as for driving in and compacting, when using the respective accessories.

Technical Specifications

Parameters AY-PMD-950G
Voltage 220V
Frequency 50Hz
Input Power 950W
Speed 0-900R/MIN
Drill 120MM

Part Diagram

Part Diagram

Part list

1| Spindle| 1| Pcs| 26| Stator| 1| pcs
2| Screw,| 4| Pcs| 27| Tapping Screw.| 2| pcs
3| Ball Bearing.| 1| Pcs| 28| Carbon Brush| 2| pcs
4| Retainer| 1| Pcs| 29| Brush Holder| 2| pcs
5| Needle Bearing,| 4| Pcs| 30| Housing| 1| pcs
6| Key.| 1| Pcs| 31| Cap| 2| pcs
7| Gear Box| 1| Pcs| 32| Rear Cover| 1| pcs
8| Retainer| 1| Pcs| 33| Handle Cap| 1| pcs
9| Gear| 1| Pcs| 34| Cord Guard| 1| pcs
10| Oil Seal Paper Washer| 1| Pcs| 35| Cord| 1| pcs
11| Cylindrical Pin| 1| Pcs| 36| Terminal| 2| pcs
12| Gear Shaft| 1| Pcs| 37| Switch| 1| pcs
13| Gear| 1| Pa| 38| Cord Clamp| 1| pcs
14| Retainer| 1| Pcs| 39| Screw.| 6| pcs
15| Gear Shaft| 1| Pcs| 40| Rear Handle Screw| 1| pcs
16| Gear| 1| Pcs| 41| Rear Handle| 1| pcs
17| Retainer| 1| Pcs| 42| Screw.| 2| Pa
18| Middle Case| 1| Pcs| 43| Screw| 1| pcs
19| Needle Bearing,| 1| Pcs| 44| Chuck Key| 1| pcs
20| Side Handle| 1| Pcs| 45| Chuck| 1| pcs
21| Ball Bearing,| 1| Pcs| 46| Connect The Head| 1| pcs
22| Baffle| 1| Pcs| 47| Spanner| 1| pcs
23| Rotor| 1| Pcs| 48| Spanner| 1| pcs
24| Ball Bearing,| 1| Pcs| 49| Spanner| 1| pcs
25| Bearing Sleeve| 1| Pcs| 50| Stir Rod| 1| pcs
| 51| Key,| 1| pcs

Kisan Kraft has a large range of products to serve the farmers. A list of our products is given below:

Brush Cutters and Accessories

  • Brush Cutter/Power Weeder
  • Backpack Brush Cutter
  • Tea Pruner
  • Pole pruner with Engine
  • Reaper Attachment
  • Blades-Circular
  • Blades (2 &3 points)
  • Baffle
  • Nylon Rope
  • Tap & Go


  • Petrol Chainsaw
  • Electric Chainsaw
  • Chain Sharpening Machine

Engines and Water Pumps

  • Engine –Diesel-(Horizontal)
  • Engine –Diesel(Vertical)
  • Engine-Kerosene
  • Water Pump with Petrol Engine
  • Water Pump with Kerosene Engine
  • Water Pump with Diesel Engine

Hand Tools

  • Secateurs
  • Folding Saw
  • Garden Rake
  • Garden Shovel
  • Hedge Shear
  • Lopper
  • Telescopic Hedge Shear
  • Telescopic Lopping Shear
  • Tree Pruner
  • Telescopic Steel Pipe & Fruit Picker Bag
  • Sheep Shear

Garden Tools

  • Electric Pressure Washer
  • Hedge Trimmer
  • Lawn Mower (Electric, Petrol & Manual)
  • Leaf Blowe

Cultivators and Accessories

  • Petrol and Diesel

Sprayers and Accessories

  • BatterySprayer
  • Portable Power Sprayer
  • Trolley Sprayer
  • Manual Knapsack Sprayer
  • Manual Pressure Sprayer
  • Rose Cans
  • Hose Crimping Machine
  • HTP Sprayer
  • HTP Delivery Hose
  • HTP Hose Reel
  • HTP Stand
  • HTP Gun / Lance(Brass Rod
  • Knapsack Power Sprayer
  • Mister / Duster / Granule Spreader
  • HTP Sprayer Set with Diesel Engine
  • HTP Sprayer Set with Kerosene Engine
  • Fogging Machine

Milking Machine

  • Wood Shredder
  • Fodder Ensiling Chaff Cutter
  • Fodder Grinder Chaff Cutter
  • Fodder Mini Chaff Cutter


  • Maize Sheller
  • Maize Sheller + Dehusker
  • Maize Combine Harvester
  • Onion Digger Carlotta Italy
  • Tea Leaf Harvester
  • Sugarcane Combine Harvester
  • Sugarcane Leaf Strippe

Transplanter and Post Hole Digger

  • Paddy Transplanter (2 & 8 Rows)
  • Transplanter-Vegetable & Tobacco
  • Post Hole Digger(4” to 14”Augers)

Wide Range of Products for Every Need

For more information give MISSED CALL: 07676065555

Many of our products have BIS: ISI certification

HO: Bangalore (Karnataka)

Sri Huchhanna Tower # 4, 1st Main, 7-A Cross, Maruthi Layout, Dasarahalli,
HAF Post, Hebbal, Bangalore – 560 024,
Phone: 080 6835 7800
Email: [email protected]

Bhubaneswar (Odisha)

Plot No. 2509, Near Toyota Showroom,
Nuagada, PO-Telengapentha, PSBanapur, Cuttack, Sadar – 753 011,
Phone: 0671 2959 166
Email:[email protected]

Hubli (Karnataka)

LG-2, Akshay Enclave, Kusugal Road
Keshwapur, Hubli – 580 023, Karnataka
Phone: 0836 2287 877
Email: [email protected]

Karnal (Haryana)

Near Shani Mandir, Bypass GT Road,
Karnal – 132 001, Haryana
Phone: +91 70822 18201
Email: [email protected]

Nellore (Andhra Pradesh)

Podalakur Sangam Road, Opp.
Sudalagunta Sugar Factory,
Prabhagiripatnam Village Podalakur
Mandal, Sri Potti Sreeramulu, Nellore –
524 345, Andhra Pradesh
Phone: 080 2217 8200
Email: [email protected]

Ahmedabad (Gujarat)

G-11, Karnavati Estate,Sarkhej – Sanand Road, Besides Hotel Orange
Inn, Ahemadabad – 382 210, Gujarat
Phone: +91 92280 00760
[email protected]

Coimbatore (Tamil Nadu)

291/7, Kothari Nagar, MTP Road,
Opp. Sai Hospital, Vadamadurai Post,
Coimbatore – 641 017, Tamil Nadu
Phone: 0422 2460 199
Email: [email protected]

Hyderabad (Telangana)

Plot No. 7, H No. 5-5-35/234, Shaktipeetam, Prashantinagar, I.D.A, Kukatpalli, Hyderabad – 500 072, Telangana
Phone: 040 4025 0114
Email: [email protected]

Kolkata (West Bengal)

Sadananda Ind. Estate, Dag No. 1183,
Mouza-Balitikuri & Dag No.1504,
Dharsa-Balitikuri, Bakkultala, Howrah –
711 113, West Bengal
Phone: 033 2955 0403
Email: [email protected]

Pune (Maharashtra)

S.R.No. 133, Village – Uruli Devanchi,
Taluka – Haveli, District – Pune – 412
308, Maharashtra
Phone: +91 84829 75446
Email: [email protected]

Bhopal (Madhya Pradesh)

Shed #1, Near C-21 Mall,
Hoshangabad Road, Bhopal – 462
026, Madhya Pradesh
Phone: +91 70242 11672
Email: [email protected]

Guwahati (Assam)

Ground Floor, Word No. 06, Near
LP School, Paschim, Boragaon
Post, Kamrup, Guwahati – 781
035, Assam
Phone: 0361 2960 299
Email: [email protected]

Jaipur (Rajasthan)

No. 69-A, Sudershanpura
Industrial Area, Bais Godam,
Jaipur – 302 006, Rajasthan
Phone: 0141 2219 128
Email: [email protected]

Lucknow (Uttar Pradesh)

Plot No. E-45, Phase-2, Transport
Nagar, Kanpur Road,
Lucknow – 226 012, Uttar Pradesh
Phone: 0522 2978 200
Email: [email protected]

Raipur (Chhattisgarh)

Block No. 5, Plot No. W1A-04, Dr.
Khoob Chand Baghel, Transport
Nagar, Rawabhata, Raipur – 492
010, Chhattisgarh
Phone: +91 91099 98071
Email: [email protected]

Tools : [email protected] : +91.80. 6835 7800

Aryantra Logo


Read User Manual Online (PDF format)


Download This Manual (PDF format)

Download this manual  >>

Related Manuals