CT5 INC TIKTAALIK Mic Plus Wireless Microphone User Manual
- June 10, 2024
- CT5 INC
Table of Contents
CT5 INC TIKTAALIK Mic Plus Wireless Microphone
Product Information
- Model Number: 90NN-70NN
- Color: Black
- Bluetooth Version: 5.0
- Sampling Frequency: 44.1Khz
- Wireless Channel: 2
- Charging Port: Type-C
- TPS Out Port: 3.5mm 4Pin
- Encoder: SBC, AAC
- Recording Bandwidth: Full Band (22kHz)
- Battery Life: 10 hours max
- Battery Capacity: 300mAh
- Noise Reduction Function: 90dB
- Bluetooth Protocol: A2DP, AVRCP, HFP, HSP, PBAP, SPP, GATT
Product Usage Instructions
On/Off Switch
The power is turned off when the menu key is depressed. Enter each mode and hold down the MF key for more than 3 seconds to activate it.
How to Charge
Charging is done using a Type-C cable. When the device is turned off, the charging light turns off. As it enters each mode, the LED indication gradually turns on and off in red, and this process is repeated. When completely charged, the light turns off.
HOW TO USE RX/TX/MIC MODES
MIC Mode (Loudspeaker)
- Press the menu key to set MIC mode.
- Hold the MF key for 3 seconds. Then, the green LED indication flashes.
- Enter pairing mode by turning on the Bluetooth speaker that will be utilized as a loudspeaker.
- Once the microphone and speaker are connected in about 1 minute, it is utilized as a loudspeaker. The LED indication becomes completely green.
- It is utilized as a loudspeaker once the microphone and speaker are connected in about 1 minute.
RX Mode
- Press the menu key to set RX mode.
- Hold the MF key for 3 seconds. Then, the white LED indication flashes.
- Connect the 3.5mm connector to the microphone and wired devices (car speakers, wired speakers, etc.)
- Check the Bluetooth connection on the smartphone and select TIKTAALIK. The LED indicator is solid white.
TX Mode
- Press the menu key to set TX mode.
- Hold the MF key for 3 seconds. Then, the blue LED indication flashes.
- Connect the 3.5mm connector to the microphone and wired devices (TV, treadmill, aircraft monitor, etc.)
- Go to pairing mode on your Bluetooth earphone or speaker.
- In about 1 minute, when the TIKTAALIK microphone and earphone or speaker are connected, the use starts. The LED indicator turns blue.
How to Record a Microphone (while using the app)
- Press the menu key to set RX mode.
- The white LED indication flashes.
- Check the Bluetooth connection on the smartphone with the app loaded and choose TIKTAALIK. The LED indicator is completely white.
- Start the TIKTAALIK app and record a video.
SPECIFICATION
- Color: Black
- BT Ver: 5.0
- Sampling frequency: 44.1Khz
- Wireless channel: 2
- Charging port: Type C
- TPS out port: 3.5mm 4Pin
- Encoder: SBC, AAC
- Recording Bandwidth: Full Band(22kHz)
- Battery life: 10 hours max
- Battery capacity: 300mAh
- Noise reduction function: 90db
- BT protocol: A2DP, AVRCP, HFP, HSP, PBAP, SPP, GATT
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>