uniojo Smart Security Camera System User Manual

uniojo Smart Security Camera System User Manual

Welcome

Thank you for purchasing an UNIOJO NVR!
Before installation and operation, please read the below safeguards carefully. Many of the setup sections below have corresponding videos on YouTube. To access the settings video, please search “uniojo” on YouTube.
NOTE: This document is applicable to UNIOJO 8005BT4 NVRs.
This document provides a quick setup and overview of your UNIOJO NVR and its features. For access to a detailed user manual or further information regarding your device please visit:
https://uniojo.com/pages/contact-us.

For product updates or other support, please email:
support@uniojo.com

Product Description

What’s in the Box

Introduce the NVR

1. USB Port: Connect mouse or USB flash disk.
2. HDMI High-Definition Interface: Connect high-definition TV.
3. VGA Output Interface: connect LCD.
4. Antenna Port: Can extend WIFI range.
5. WAN Port: Connect NVR to the Internet.
6. DC seat: DC power input .(12V/2A)

Introduce the Cameras

1. DC Seat: DC power input .(12V/2A)
2. RJ45 Port: This network port is used for code and wired. connection. It has been coded when leaving factory. If it s necessary to recode or carry out wired connection by network port, you can read following introduction of adding video camera.
3. DC Interface: Power input .(12V/1A)

Installation Notes

Installation and Connection

Please check the YouTube video for installation instructions. Before setting up the NVR, you need the following items. These items may not be included:

1. Computer monitor or TV with HDMI or VGA input.
2. A power board, which can accommodate 4 large power plugs
3. Hard disk for storing video.
4. Small screwdriver.

Set Up the Cable Connection
The following instructions will show you how to set up the cable for the NVR, camera, and monitor or TV screen.To set up the cable connection, there are 6 main steps:

1. Connect the hard disk in the package to the NVR.
2. Connect the monitor or TV screen to your NVR. NVR is compatible with any monitor or screen connected using VGA or HDMI. For the purpose of this guide, we will use a VGA connection. Take a VGA cable and connect one end to the VGA port on the monitor/screen, and the other end to the VGA port on the rear panel of the NVR.
3. Connect the Ethernet cable to the router. Then, connect the other end of the cable to the Ethernet port on the back of the NVR.
4. Connect the mouse with the USB cable to the USB port on the back of the NVR.
5. Connect the power cord of the NVR to the power port on the back of the NVR. And plug in the power source.

Multi-Channel Viewing

Mobile Phone Remote Viewing

Please check the YouTube video for instructions.

1. Download the “Goseeview” APP.
2. Right-click with the mouse> select “System setup”> select”Network setup”> select “Network setup”> click “Show QR Code”> a QR code appears, and the mobile phone scans to connect.
3. Run the “Goseeview” APP, log in to your account —> click “+” to pop up “Scan” and scantheabove two-dimensional code to add a device.

Computer Remote Viewing
Please check the YouTube video for instructions.

1. Enter www.uniojo.com. (Support> Download APP> NVR 8005BT4 EseeCloud SET UP)
2. Download “EseeCloud” and install it on your computer (please note: please choose the default path to install).
3. Use the account and password registered in the “Goseeview” APP to log in.
4. After the login is successful, click “Add Device” in the upper right corner> enter the device ID number to add the device (To obtain the ID number, please see the YouTube video guide).
5. After the addition is successful, click “Play” in the device list to view the monitoring screen.

Frequently Asked Questions

Please note that all settings need to be performed on the NVR, and the NVR needs to be connected to the display screen to make changes in the system.

System Operation Problems
Q: How to log in ?
A: No need to enter a password, please click “Login” directly.
Q: I forgot my login password, how can I change it?
A: If you use the CMS system to view, right-click on the system settings in the image interface and select User Management under System Management to see the option to modify the password. If you connect the screen directly with a cable, the method is as follows (the following methods will not affect the original video): a: After entering “80816553” to log in, change the password. b:Enter the wrong password, and click on the left and right buttons at the prompt “the window with incorrect user name and password” outside of “OK”, click each of the left and right buttons once, repeat six times, and click 12 times in total. After that, it will jump to the password modification interface.
Q: The hard disk does not automatically record?
A: At very beginning, the hard disk needs to be formatted.

Q: The hard disk storage space is full, but the original video is not automatically overwritten. How to set it up?
A: Please set it in the following way:Right-click> select “System setup”> select “General setup”> check “Overwrite”> select “Apply”.
Q: How to set the mobile phone APP alarm reminder?
A: Please set it in the following way:Right-click> select “System setup”> select “Network setup’s select “Channel setup”> select “Video detection”> select “APP Alarm”.
Q: How to set up email reminder?
A: Please set it in the following way:Right-click> select “System setup”> select “Network setup”> select “Channel setup”> select “Video detection”> select “Mail Alarm”.
Q: How to backup videos?
A: Insert the USB flash drive with USB port into the NVR USB port.Make settings in the system.
Q: How to check the files that have been backed up to the USB flash drive? A: Can not be viewed on the computer. Since all our files are encrypted, you can only view them through the system. No need to worry about others invading your privacy.

Q: Is the data on the hard disk encrypted?
A: Yes. All data uses advanced military-grade encryption technology. No one can access your information without your permission.
Q: Can it be recorded?
A: Can not. Currently the device does not support this function.
Q: Is it recorded 24 hours a day?
A: Yes. You can also set a specific time to record in the system.
Q: Can I connect the NVR to USB wife?
A: Can not. The NVR can also record when it is not connected to the Internet. If you need to view, you need to connect to the NVR with a cable.

Mobile APP Operation Problems

1.Q: How to add equipment?
A: Please check the YouTube video for the instructions (1)Download the “Goseeview” APP (2)Right-click with the mouse> select “System setup”> select”Network setup”> select “Network setup”> click “Show QR Code”> a QR code appears, and the mobile phone scans to connect. (3)Run the “Goseeview” APP, log in to your account —) click “+” to pop up “Scan” and scan the above two- dimensional code to add a device.

Q: Does he phone need to he Or. the Scr’le “CLVOlk es the cicvaa
A: Unnecessary. Mobile data can also be viewed using mobile phones.
Q: Can I download videos on my mobile phone?
A: Yes. Please operate on your mobile phone for details. After the download is complete, the video will be saved in the phone photo album.
Q: Is it possible to fast forward and play videos on the APP?
A: No
Q: Can I download the app on the tablet?
A: Yes. Please go to google play or app store to download.

Computer Remote Operation Problems

Q: How to add equipment?
A: Please check the YouTube video for the instructions Please proceed as follows:

1. Enter www.uniojo.com. (Support> Download APP> NVR 8005814 EseeCloud SET UP)
2. Download ‘EseeCloud’ and install it on your computer (please note: please choose the default path to install).
3. Use the account and password registered in the “Goseeview’ APP to log in.
4. After the login is successful, click “Add Device’ in the upper right corner> enter the device ID number to add the device (To obtain the ID number, please see the YouTube video guide).
5. After the addition is successful, click ‘Play’ in the device list to view the monitoring screen.

Q: How to play real-time images?
A: After adding the device, click “Real-time screen”, right-click the IP address in the “Device list” to display the screen.
Q: How to play back the video?
A: After adding the device, click “Video playback”. First select the date to view. Then right-click the IP address in the “Device List” to display the screen.
Q: Can I download videos on my computer?
A: Yes.You can download videos on your computer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>